Omron JPN600 Instruction Manual

1 to 2 cm

Year

Month

Day

Hour

Minute

B C

Thank you for purchasing the OMRON JPN600 Automatic Blood Pressure Monitor.

The OMRON JPN600 is a compact, fully automatic blood pressure monitor, operating on the oscillometric principle. It measures your blood pressure and pulse rate simply and quickly. For comfortable controlled inflation without the need of pressure pre-setting or re-inflation the device uses its advanced “IntelliSense” technology.

Intended Use This product is designed to measure the blood pressure and pulse rate of people within the range of the designated arm cuff, following the instructions in this instruction manual. It is mainly designed for general household use. Please read the Important Safety Information in this instruction manual before using the unit.

Please follow this instruction manual thoroughly. Please keep for future reference. For specific information about your own blood pressure, CONSULT YOUR DOCTOR.

Please read this section carefully before using the unit.

Warning: Indicates a potentially hazardous situation which, if not avoided,

could result in death or serious injury.

(General Usage)

•DO NOT adjust medication based on measurement results from this blood

pressure monitor. Take medication as prescribed by your doctor. Only a doctor is qualified to diagnose and treat High Blood Pressure.

•Consult your doctor before using the device for any of the following

conditions: common arrhythmias such as atrial or ventricular premature beats or atrial fibrillation, arterial sclerosis, poor perfusion, diabetes, age, pregnancy, pre-eclampsia, renal diseases. Note that PATIENT motion, trembling, shivering may affect the measurement reading.

•Do not use the device on the injured arm or the arm under medical treatment.

•Do not apply the arm cuff on the arm while being on an intravenous drip or

blood transfusion.

•Consult your doctor before using the device on the arm with an arteriovenous (A-V) shunt.

•Do not use the device with other medical electrical (ME) equipment simultaneously.

•Do not use the device in the area the HF surgical equipment, MRI, or CT

scanner exists, or in the oxygen rich environment.

•The air tube or the AC adapter cable may cause accidental strangulation in

infants.

•Contains small parts that may cause a choking hazard if swallowed by

infants.

•Stop using the unit and consult your doctor if you experience skin irritation or

other troubles.

(AC Adapter (optional) Usage)

• Do not use the AC adapter if the unit or the power cord is damaged. Turn off

the power and unplug the power cord immediately.

•Plug the AC adapter into the appropriate voltage outlet. Do not use a

multiple-tap.

•Never plug in or unplug the power cord from the electric outlet with wet

hands.

Caution: Indicates a potentially hazardous situation which, if not avoided,

may result in minor or moderate injury to the user or patient or damage to the equipment or other property.

(General Usage)

•Always consult your doctor. Self-diagnosis of measurement results and self-treatment are dangerous.

•Consult your doctor before using the device for any of the following conditions:

-If you have had a mastectomy.

-People with severe blood flow problems or blood disorders as cuff inflation

can cause bruising.

•Do not take measurements more than necessary. It may cause bruising due to blood flow interference.

•If there are any abnormalities during the measurement, remove the arm cuff.

•Do not use this device on infants or persons who cannot express their

intentions.

•Do not inflate the arm cuff more than necessary.

•Do not use the unit for any purpose other than measuring blood pressure.

•Use only the approved arm cuff for this device. Use of other arm cuffs may

result in incorrect measurement results.

•Do not use a mobile phone or other devices that emit electromagnetic fields, near the device. This may result in incorrect operation of the device.

•Do not disassemble the monitor or arm cuff. This may cause an inaccurate reading.

•Do not use in a location with moisture, or a location where water may splash on the device. This may damage the device.

•Do not use the device in a moving vehicle (car, airplane).

(Battery Usage)

•Do not insert the batteries with their polarities incorrectly aligned.

•Use only four “AA” alkaline or manganese batteries with this unit. Do not use

other types of batteries. Do not use new and used batteries together.

•Remove the batteries if the unit will not be used for 3 months or more.

(AC Adapter (optional) Usage)

•Fully insert the power plug.

•When disconnecting the power plug, do not pull the power cord. Be sure to

hold the power plug.

Important Safety Information

This marking shown on the product or its literature, indicates that it should not be disposed of, with other household wastes at the end of its working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate this product from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources.

Household users should contact either the retailer where they purchased this product, or their local government office, for details of where and how they can return this item for environmentally safe recycling. Business users should contact their supplier and check the terms and conditions of the purchase contract. This product should not be mixed with other commercial wastes for disposal.

Correct Disposal of This Product (Waste Electrical & Electronic Equipment)

Made in Japan

Manufacturer

Introduction

1. Overview

Main unit:

N. Average value symbol O. Memory symbol P. Irregular heartbeat symbol Q. Systolic blood pressure R. Diastolic blood pressure S. Low battery symbol T. Cuff wrapping guide

2.1 Installing/Replacing the Batteries

2. Preparation

Remove the battery cover.

2.2 Setting the Date and Time

Press the button.

Set the monitor to the correct date and time before taking a measurement for the first time.

Press the START/STOP button to store the setting.

Notes:

• If the batteries have been replaced, the date and time setting will

need to be reset.

• If the date and time are not set, “-:--” appears during or after

measurement.

Insert four “AA” batteries as indicated in the battery compartment and then replace the battery cover.

Notes:

• If the low battery symbol ( ) appears on the display, turn the monitor off then replace all batteries at the same time.

• The measurement values continue to be stored in memory even after

the batteries are replaced.

• The supplied batteries may have a shorter life.

• Dispose of the device, components and optional accessories

according to applicable local regulations. Unlawful disposal may cause environmental pollution.

The bottom edge of the arm cuff should be 1 to 2 cm above the elbow. Marker (arrow under the air tube) is centred on the middle of your inner arm.

3.3 Taking a Reading

6. Technical Data

4.3 Maintenance

Calibration and Service

To protect your unit from damage, please observe the following:

Notes:

• When you take a measurement on the right

arm, the air tube will be at the side of your elbow. Be careful not to rest your arm on the air tube.

Notes:

• To cancel a measurement, press the START/STOP button to release

the air in the arm cuff.

• Remain still while taking a measurement.

Press the START/STOP button.

The arm cuff will start to inflate automatically.

• Do not subject the main unit and the cuff to extreme

temperatures, humidity, moisture or direct sunlight.

• Do not fold the cuff or tubing tightly.

• Do not disassemble the unit.

• Do not subject the unit to strong shocks or vibrations

(for example, dropping the unit on the floor).

• Do not use volatile liquids to clean the main unit.

• Do not wash the arm cuff or immerse it in water.

• Do not use petrol, thinners or similar solvents to clean

the arm cuff.

• Do not carry out repairs of any kind yourself. If a defect

occurs, consult your local OMRON representative.

• The accuracy of this blood pressure monitor has been

carefully tested and is designed for a long service life.

• It is generally recommended to have the unit inspected

every two years to ensure correct functioning and accuracy. Please consult your local OMRON representative.

• The unit should be cleaned with a soft, dry cloth.

• Use a soft, moistened cloth and neutral soap to clean

the arm cuff.

Automatic Blood Pressure Monitor JPN600 LCD Digital Display Oscillometric method Pressure: 0 to 299 mmHg Pulse: 40 to 180 beats/ min.

Pressure: ±3 mmHg

Pulse: ±5% of display reading Fuzzy-logic controlled by electric pump Automatic pressure release valve 90 measurements with date and time IP 20

DC6V 4W

4 “AA” batteries 1.5V or AC adapter (optional, INPUT AC100-240V 50/60Hz 0.12A) Approx. 1000 measurements (using new alkaline batteries) Main Unit: 5 years Cuff: 1 year (when used 6 times a day)

= Type BF

Internally powered ME equipment (When using only

the batteries)

= Class II ME equipment (Optional AC adapter)

+10 to +40°C / 30 to 85% RH / 700 to 1060 hPa

-20 to +60°C / 10 to 95% RH / 700 to 1060 hPa

Approx. 280g without batteries

Approx. 130g Approx. 107 (w) mm × 79 (h) mm × 141(l) mm

Approx. 145 mm × 466 mm

(Cuff: arm circumference 22 to 32 cm)

Nylon, polyester, polyvinyl chloride Main unit, arm cuff, instruction manual, battery set, storage case, EMC information

3.2 How to Sit Correctly

To take a measurement, you need to be relaxed and comfortably seated, under comfortable room temperature. Avoid bathing, drinking alcohol or caffeine,

smoking, exercising or eating 30 minutes

before taking a measurement. Also avoid taking measurements during stressful time. Stress raises blood pressure.

• Sit on a chair with your legs uncrossed and

your feet flat on the floor.

• Sit upright with your back straight.

• Sit with your back and arm being supported.

• The arm cuff should be placed on your arm

at the same level as your heart.

• The blood pressure can differ between the right arm and the left arm,

and therefore also the measured blood pressure values can be different. OMRON recommends to always use the same arm for measurement. If the values between both arms differ substantially, please check with your doctor which arm to use for your measurement.

Press and hold the START/STOP

button for more than 3 seconds.

The date/time display will disappear.

Release the START/STOP button when the date/time display turns off.

The arm cuff will start to inflate automatically.

The monitor stores measurement values for one user in the memory. The guest mode can be used to take a single measurement for another user. No measurement values are stored in the memory when the guest mode is selected.

START

INFLATE DEFLATE

COMPLETE

1. Unplug the air plug from the air jack.

• Keep the unit in its storage case when not in use.

• Store the device and the components in a clean, safe location.

2. Gently fold the air tube into the arm cuff.

4.4 Storage

Product Description Model Display Measurement Method Measurement Range

Accuracy

Inflation Deflation Memory IP classification Rating Power Source

Battery Life

Durable Period

Applied Part

Protection Against Electric Shock

Operating temperature/ Humidity / Air Pressure Storage temperature/ Humidity/ Air pressure

Console Weight Cuff Weight

Outer Dimensions Cuff Dimensions

Cuff/ Tube Material Package Contents

•This device fulfils the provisions of EC directive 93/42/EEC (Medical Device

Directive).

•This blood pressure monitor is designed according to the European Standard EN1060, Non-invasive sphygmomanometers Part 1: General Requirements

and Part 3: Supplementary requirements for electromechanical blood

pressure measuring systems.

•This OMRON product is produced under the strict quality system of OMRON HEALTHCARE Co., Ltd., Japan. The core component for OMRON blood pressure monitors, which is the Pressure Sensor, is produced in Japan.

OMRON HEALTHCARE Co., Ltd.

53, Kunotsubo, Terado-cho, Muko, KYOTO, 617-0002 JAPAN

OMRON HEALTHCARE EUROPE B.V.

Scorpius 33, 2132 LR Hoofddorp, THE NETHERLANDS

Production facility

OMRON HEALTHCARE Co., Ltd. Matsusaka Factory

Mie, JAPAN

Asia Pacific HQ

OMRON HEALTHCARE SINGAPORE PTE LTD.

438A Alexandra Road, #05-05/08, Alexandra Technopark, Singapore 119967

www.omronhealthcare-ap.com

Automatic Blood Pressure Monitor

Model JPN600

Instruction Manual

A. Display B. Memory button C. START/STOP button D. Date/Time setting ( ) button E. Cuff wrapping guide lamp

F. Up/Down ( ) buttons G. Battery compartment H. AC adapter jack (for optional

AC adapter)

I. Air jack

U. Heartbeat symbol

•Flashes during measurement.

V. Date/Time display

W. Movement error symbol

X. Blood pressure level indicator Y. Deflation symbol Z. Pulse display and Memory

number

Push or buttons to change.

Push the button to confirm. Next setting appears.

If your systolic pressure is more than 210 mmHg

After the arm cuff starts to inflate, press and hold the START/STOP

button until the monitor inflates 30 to 40 mmHg higher than your

expected systolic pressure.

Notes:

• The monitor will not inflate above 299 mmHg.

• Do not apply more pressure than necessary.

Cuff Wrapping Guide Lamp

• If you move during measurement, the movement

error symbol ( ) will appear on the display.

Keep still and repeat the measurement.

Display:

3100085-2A

J. Arm cuff (Arm circumference

22 - 32 cm)

K. Air plug

L. Air tube M.Marker

Arm cuff:

• Your blood pressure monitor includes an

irregular heartbeat feature. Irregular heartbeats can influence the results of the measurement. The irregular heartbeat algorithm automatically determines if the measurement is usable or needs to be repeated. If the measurement

3. Using the Unit

1. Insert the air plug into the air jack

securely.

3.1 Applying the Arm Cuff

Remove tight-fitting clothing or tight rolled up sleeve from your upper arm. Do not place the arm cuff over thick clothes.

Remove the arm cuff.

Press the START/STOP button to turn the monitor off.

The monitor automatically stores the measurement in its memory. It will automatically turn off after 2 minutes.

Note: Wait 2-3 minutes before taking another blood pressure

measurement. Waiting between readings allows the arteries to

return to the condition prior to taking the blood pressure measurement.

Put your arm through the cuff loop.

Close the fabric fastener FIRMLY.

Using the Guest Mode

Cuff Wrapping Guide Lamp:

Note: Do not bend the air tube excessively.

3. Place the arm cuff and main unit in

the storage case.

Do not store the unit in the following situations:

•If the unit is wet.

•Locations exposed to extreme temperatures,

humidity, direct sunlight, dust or corrosive vapors such as bleach.

•Locations exposed to vibrations, shocks or

where it will be at an angle.

Systolic Blood Pressure ≥ 135 mmHg

Diastolic Blood Pressure ≥ 85 mmHg

Important:

This criteria is for home blood pressure measurement.

• Recent research suggests that the following

values can be used as a guide to high blood pressure for measurements taken at home.

results are affected by irregular heartbeats but the result is valid, the result is shown together with the irregular heartbeat symbol ( ). If the irregular heartbeats cause the measurement to be invalid, no result is shown. If the irregular heartbeat symbol ( ) is shown after you have taken a measurement, repeat the measurement. If the irregular heartbeat symbol ( ) is shown frequently, please make your doctor aware of it.

Note: Read and follow the “Correct Disposal of This Product” in the

Technical Data Section when disposing of the device and any used accessories or optional parts.

The cuff wrapping guide lamp lights in green, the cuff is correctly wrapped tightly enough on the arm and the reading is accurate and reliable. If it does not light, the reading is not reliable due to the incorrect wrapping of the cuff. Please wrap the cuff again, taking care to wrap it correctly and take the measurement again.

3.4 Using the Memory Function

Notes:

• If the previous reading was taken without setting

the date and time, the average value is not calculated.

• If there are no measurements results stored in

the memory, the screen to the right is displayed.

The monitor automatically stores the result up to 90 sets. It can also calculate an average reading based on the measurements from the last three readings taken within 10 minutes. If there are only two readings in memory for that period, the average will be based on two readings. If there is one reading in memory for that period, the average will be based on one reading.

Notes:

• If the memory is full, the monitor will delete the oldest reading.

• When viewing the reading taken without setting the date and time,

“-:--” is displayed instead of the date and time.

Alternating date/time display

Press the button.

The Memory number appears for a second before the pulse rate is displayed. The newest set is numbered “1”.

To View the Readings Stored in Memory

4. Troubleshooting and Maintenance

4.1 Error Messages

4.2 Troubleshooting

Problem

Cause Remedy

The reading is extremely low (or high).

Arm cuff not applied correctly.

Movement or talking during measurement.

Clothing is interfering with the arm cuff.

Apply the arm cuff correctly.

Refer to section 3.1.

Remain still and do not talk during measurement.

Refer to section 3.3.

Remove any clothing interfering with the arm cuff.

Refer to section 3.1.

The batteries are low.

The batteries are exhausted.

Air plug disconnected.

Movement during measurement and the arm

cuff has not been inﬂated sufﬁciently.

The arm cuff was inﬂated

above 299 mmHg

when inﬂating the cuff

manually.

Movement during measurement.

Clothing is interfering with the arm cuff.

Device error.

Irregular heartbeats are detected.

Remove the arm cuff. Wait 2 - 3 minutes and then take

another measurement. Repeat the steps in section

3.3. If this error continues to

appear, contact your doctor.

Movement during measurement.

Carefully read and repeat

the steps in section 3.3.

You should replace them with new ones ahead of time. Refer to section 2.1.

You should replace them with new ones at once. Refer to section 2.1.

Insert the plug securely.

Refer to section 3.1.

Arm cuff not applied correctly.

Apply the arm cuff correctly.

Refer to section 3.1.

Air is leaking from the arm cuff.

Replace the cuff with the new one. Refer to Chapter 5.

Repeat measurement. Remain still and do not talk during measurement.

Refer to section 3.3.

If “E2” appears repeatedly,

inﬂate the cuff manually until it is 30 to 40 mmHg

above your previous measurement result.

Refer to section 3.3.

Do not inﬂate the cuff above

299 mmHg.

Refer to section 3.3.

Repeat measurement. Remain still and do not talk during measurement.

Refer to section 3.3.

Remove any clothing interfering with the arm cuff.

Refer to section 3.1.

Contact your

local OMRON

representative

Cause RemedyError Display

Problem

Cause Remedy

Cannot measure or readings are too low or too high.

The arm cuff has not been inflated sufficiently.

Inflate the cuff so that it

is 30 to 40 mmHg above

your previous measurement result.

Refer to section 3.3.

•Press the START/STOP button and repeat

measurement.

•If the problem continues, try replacing the

batteries with new ones. If this still does not solve the problem, contact your local OMRON representative.

Nothing happens when you press the buttons.

Omron JPN600 Instruction Manual

Specifications and Main Features

Frequently Asked Questions

User Manual