Page 1
Instruction Manual
Bluetooth® Body Composition
Monitor
Model HBF-206IT
Page 2
TABLE OF CONTENTS
Before Using the Monitor
Introduction...................................................................................................... 3
Safety Information ........................................................................................... 4
Information on Body Composition .................................................................. 6
Principles of Body Composition Calculations ........................................... 6
Body Mass Index........................................................................................ 6
Body Fat ..................................................................................................... 7
Visceral Fat................................................................................................. 8
Resting Metabolism.................................................................................... 9
Skeletal Muscle ........................................................................................ 10
Body Age.................................................................................................. 10
Long-term Planning for Successful Weight Loss..................................... 11
Recommended Measurement Times ........................................................ 12
Know Your Unit ............................................................................................. 14
Operating Instructions
Battery Installation......................................................................................... 16
Setting the Date and Time.............................................................................. 18
Setting Personal Data ..................................................................................... 20
Selecting Measurement Unit .................................................................... 22
Changing Personal Data ........................................................................... 23
Deleting Personal Data ............................................................................. 24
How to Take a Measurement.......................................................................... 25
Understanding Your Measurement Results.................................................... 28
How to Measure Weight Only........................................................................ 29
Viewing the Last Measurement Results......................................................... 30
Transferring the Data ..................................................................................... 32
About the Wireless Communications Function ............................................. 35
Care and Maintenance
Error Indicators .............................................................................................. 36
Troubleshooting Tips ..................................................................................... 37
Care and Maintenance.................................................................................... 39
FCC Statement ............................................................................................... 40
Warranty......................................................................................................... 41
Specifications ................................................................................................. 42
Before Using the Monitor
2
Page 3
INTRODUCTION
Thank you for purchasing the OMRON® product.
Fill in for future reference.
DATE PURCHASED:
SERIAL NUMBER:
Staple your purchase receipt here
This product is easy to use. The monitor calculates the estimated values for body fat percentage, skeletal
muscle percentage, resting metabolism and visceral fat level using the BI (Bioelectrical Impedance)
Method. The monitor also calculates the BMI (Body Mass Index) and body age as well as weight. Push
your Personal Profile Number to turn the power switch on, and step onto the measurement platform. The
personal memory function can be used to store data for up to four personal profiles.
This product comes with the following components:
• Monitor
• Instruction Manual
• 4 “AA” Alkaline Batteries
WARNING
Do not use, or allow others to use, this monitor if fitted with a cardiac pacemaker or other
implanted medical device.
WARNING
Pregnant women should not use this device.
CAUTION
Read all of the information in the instruction manual and any other literature in the box before
operating the unit.
SAVE THESE INSTRUCTIONS
3
Page 4
SAFETY INFORMATION
To assure the correct use of the product, basic safety measures should always be followed including the
warnings and cautions listed in this instruction manual.
SAFETY SYMBOLS USED IN THIS INSTRUCTION MANUAL
Indicates a potentially hazardous situation which, if not avoided, could result
WARNING
CAUTION
OPERATING THE DEVICE
Do not use, or allow others to use, this monitor if fitted with a cardiac pacemaker or other implanted medical
device. The monitor passes an extremely weak electrical current of 50kHz and less than 500µA through your
body when taking a measurement to determine the amount of fat tissue. This weak current is not felt while
using the monitor.
Do not begin a weight reduction or exercise program without consulting your physician or healthcare provider
first.
Self-diagnosis could damage your health.
in death or serious injury.
Indicates a potentially hazardous situation which, if not avoided, may result
in minor or moderate injury to the user or patient or damage to the equipment
or other property.
Keep the monitor out of the reach of young children.
If battery fluid should get in your eyes, immediately rinse with plenty of clean water. Contact your physician
immediately.
Persons with disabilities or persons who are physically frail should be assisted by another person when using
this monitor or use a handrail, a walker, or other support device to prevent falling when stepping on and off the
monitor.
Read all of the information in the instruction manual and any other literature in the box before operating the unit.
Do not use microwave ovens or other devices that generate strong electrical or electromagnetic fields near the
monitor. This may result in an operational failure.
Do not use mobile phones near the unit except for wireless communications.
Interference from the phone may make it difficult to obtain accurate measurements.
Do not step on the edge or the display area of the measurement platform. The monitor may tilt. The display unit
may be damaged.
Do not step on the measurement platform when your body or feet are wet, for example after taking a bath or
shower. You may slide and lose your balance.
Do not place the monitor on a cushioned floor surface such as a carpet or mat. A correct measurement may not
be possible.
Do not use the unit on slippery surfaces such as tile floors or wet floors. The monitor may move. You may lose
your balance and fall.
Do not jump on the measurement platform. You may lose your balance and fall. The monitor may be damaged.
4
Page 5
SAFETY INFORMATION
OPERATING THE DEVICE (continued)
Stand on the measurement platform with bare feet. Attempting to stand on the measurement platform when
wearing socks may cause you to slip and lose your balance.
Do not insert the batteries with their polarities incorrectly aligned.
Do not use new and worn batteries together.
Do not use batteries of a different kind together.
Replace old batteries with new ones. Replace all four batteries at the same time.
Remove the batteries if the unit will not be used for three months or more.
Do not expose the batteries to flames or fire.
If battery fluid should get on your skin or clothing, immediately rinse with plenty of clean water.
Dispose of the device, batteries, components and optional accessories according to applicable local regulations.
Unlawful disposal may cause environmental pollution.
Operate the unit only as intended. Do not use for any other purpose.
This unit is intended for home use only. It is not intended for professional use in hospitals or other medical
facilities. This unit does not support the standards required for professional use.
Always wash your feet before using the unit if you are suffering from a foot infection or other skin disease.
Failure to do so could infect others.
When the unit will be used by several people, wipe the unit with a damp cloth moistened with mild detergent
after using it. Then wipe it dry.
CARE AND MAINTENANCE
Do not disassemble or modify the unit. Changes or modifications not approved by Omron Healthcare will void
the user warranty.
Do not subject the monitor to strong shocks, such as dropping the unit on the floor.
Do not submerge the device or any of the components in water.
5
Page 6
INFORMATION ON BODY COMPOSITION
PRINCIPLES OF BODY COMPOSITION CALCULATIONS
How Omron calculates your body composition:
Omron’s algorithm focuses on the Bioelectrical Impedance Method as well as height, weight,
age and gender.
Bioelectrical Impedance Method: The monitor estimates the body fat percentage by the
Bioelectrical Impedance Method. Muscles, blood, bones and body tissues with high water content
conduct electricity easily. On the other hand, body fat does not store much water, therefore has little
electric conductivity. The monitor sends an extremely weak electrical current of 50 kHz and less than
500 µA through your body to determine the amount of water in each tissue. You will not notice or feel
the electrical current.
BODY MASS INDEX
Body Mass Index (BMI) is a number calculated from a person’s weight and height. BMI is a reliable
indicator of body fatness for people. BMI does not measure body fat directly, but research has shown that
BMI correlates with direct measures of body fat. BMI is used as a screening tool to identify possible
weight problems for adults.
BMI is calculated by using the following formula based on a ratio between your weight and height:
BMI = weight (lb) / height (inches) / height (inches) × 703
Interpreting the BMI Result
BMI BMI (Designation by the WHO)
Less than 18.5 Underweight
18.5 or more and less than 25 Normal
25 or more and less than 30 Overweight
30 or more Obese
Source: Values for obesity judgment proposed by WHO, the World Health Organization.
6
Page 7
INFORMATION ON BODY COMPOSITION
BODY FAT
Body fat serves a vital role in storing energy and protecting internal organs. We carry two types of fat in
our bodies: 1) essential fat which is stored in small amounts to protect the body and 2) stored fat which is
stocked for energy during physical activity. While too much body fat may be unhealthy, having too little
fat can be just as unhealthy. Also, the distribution of body fat in men and women is different, so the basis
for classifying the body fat percentage is different between the genders.
Interpreting the Body Fat Percentage Result
The table below is based on research by Gallagher et al., American Journal of Clinical Nutrition, Vol. 72,
Sept. 2000, and classified into four levels by Omron Healthcare.
Gender Age – (Low) 0 (Normal) + (High) ++ (Very High)
_
_
>
39.0%
_
_
>
40.0%
_
_
>
42.0%
_
_
>
25.0%
_
_
>
28.0%
_
_
>
30.0%
Female
Male
20-39 < 21.0% 21.0 - 32.9% 33.0 - 38.9%
40-59 < 23.0% 23.0 - 33.9% 34.0 - 39.9%
60-80 < 24.0% 24.0 - 35.9% 36.0 - 41.9%
20-39 < 8.0% 8.0 - 19.9% 20.0 - 24.9%
40-59 < 11.0% 11.0 - 21.9% 22.0 - 27.9%
60-80 < 13.0% 13.0 - 24.9% 25.0 - 29.9%
7
Page 8
INFORMATION ON BODY COMPOSITION
VISCERAL FAT
Visceral fat is found in the abdomen and surrounding vital organs. It is different from fat found directly
underneath the skin, which is referred to as subcutaneous fat. Visceral fat can go largely unnoticed
because it’s not visible to the naked eye. One way visceral fat can be seen is through Magnetic
Resonance Imaging (MRI).
MRI Cross Section at the Navel Level
Subcutaneous Fat
Visceral Fat
Spine
Too much visceral fat is thought to be closely linked to increased levels of fat in the bloodstream, which
may lead to conditions such as high cholesterol, heart disease and type 2 diabetes. In order to prevent or
improve these conditions, it is important to try to reduce the amount of visceral fat levels to an acceptable
level.
Interpreting the Visceral Fat Level Result
_
_
Visceral Fat Level 9
<
0 (Normal)
Visceral fat area (0 - approx. 300 cm2, 1 inch=2.54 cm) distribution with 30 levels.
Source: Omron Healthcare
NOTE: Visceral fat levels are relative and not absolute values.
_
_
<
10 Visceral Fat Level 14
_
_
<
+ (High)
Visceral Fat Level 15
++ (Very High)
_
_
>
8
Page 9
INFORMATION ON BODY COMPOSITION
RESTING METABOLISM
Regardless of your activity level, a minimum level of caloric intake is required to sustain the body’s
everyday functions. Known as the resting metabolism, this indicates how many calories you need to
ingest in order to provide enough energy for your body to function.
60-70% of daily energy use is for resting metabolism
The total amount of energy used by the body in a typical day is as follows:
Resting metabolism Energy required to maintain vital functions.
Energy used for daily activities such as
Daily activity metabolism
Diet-induced thermogenesis Energy emitted after eating a meal.
The ratio of these is 60%-70% for resting metabolism, 20%-30% for daily activity, and 10% for diet
induced thermogenesis. This means that resting metabolism accounts for most of our daily energy
consumption.
If our daily caloric intake exceeds the amount of energy required for these activities, the additional
calories can be stored as fat.
commuting to work, household chores,
hobbies etc.
Calories
Food
Calories
Diet-induced thermogenesis
Daily activity metabolism
Resting metabolism
9
Page 10
INFORMATION ON BODY COMPOSITION
SKELETAL MUSCLE
Skeletal muscle is the type of muscle that we can see and feel. When you work out to increase muscle
mass, skeletal muscle is being exercised. Skeletal muscles attach to the skeleton and come in pairs -- one
muscle to move the bone in one direction and another to move it back the other way. Increasing skeletal
muscle will increase your body’s energy requirements. The more muscle you have, the more calories
your body will burn. Building skeletal muscle can help prevent “rebound” weight gain. The maintenance
and increase of skeletal muscle is closely linked to resting metabolism rate.
Interpreting the Skeletal Muscle Percentage Result
Gender Age – (Low) 0 (Normal) + (High) ++ (Very High)
_
_
>
35.4%
_
_
>
35.2%
_
_
>
35.0%
_
_
>
44.1%
_
_
>
43.9%
_
_
>
43.7%
Female
Male
18-39 < 24.3% 24.3 - 30.3% 30.4 - 35.3%
40-59 < 24.1% 24.1 - 30.1% 30.2 - 35.1%
60-80 < 23.9% 23.9 - 29.9% 30.0 - 34.9%
18-39 < 33.3% 33.3 - 39.3% 39.4 - 44.0%
40-59 < 33.1% 33.1 - 39.1% 39.2 - 43.8%
60-80 < 32.9% 32.9 - 38.9% 39.0 - 43.6%
Source: Omron Healthcare
BODY AGE
Body age is based on your resting metabolism. Body age is calculated by using your weight, body fat
percentage and skeletal muscle percentage to produce a guide to whether your body age is above or
below the average for your actual age.
10
Page 11
INFORMATION ON BODY COMPOSITION
WARNING
Contact your physician or healthcare provider before beginning a weight reduction or exercise program.
LONG-TERM PLANNING FOR SUCCESSFUL WEIGHT LOSS
There are lots of reasons for people to lose weight. To be healthier. To look better. To feel better. To have
more energy.
No matter what the reason, successful weight loss and healthy weight management depend on sensible
goals and expectations. If you set sensible goals for yourself, chances are you'll be more likely to meet
them and have a better chance of keeping the weight off.
The foundation of a successful weight loss program remains a combination of a healthy diet and exercise
customized for you. Simply reducing food intake to lose weight can lead to a decline in muscle mass and
bone density. So even though your weight goes down, your resting metabolism is reduced making the
body more prone to putting on fat. More skeletal muscle can prevent “rebound” weight gain.
The monitor tracks your progress by monitoring weight, skeletal muscle, body fat, BMI and resting
metabolism rate to help you reach your goals.
Here’s a comparison of losing weight quickly versus slowly:
Example comparing the same loss of 20 lb:
Weight
(lb)
170
160
150
A starvation diet produces rapid
weight loss of 20 lb,
but disrupts body mass...
Fat reduction: 6 lb
Lean body mass reduction
(muscle, bone, etc.): 14 lb
Change in body fat percentage
Before diet:
1234567
A healthy diet
with weight loss of 20 lb...
Change in body fat percentage
Body fat percentage
36.0%
Before diet:
Months
Fat reduction: 18 lb
Lean body mass reduction
(muscle, bone, etc.): 2 lb
Body fat percentage
36.0%
After diet:
Lean body mass (muscle, bone, etc.)
greatly reduced, while the body fat
percentage has not changed.
36.9%
Use the separate Measurement Log Sheet to help you understand your body composition results.
11
After diet:
Body fat percentage reduced to a normal
level.
28.3%
Page 12
INFORMATION ON BODY COMPOSITION
RECOMMENDED MEASUREMENT TIMES
Being aware of the times when the body fat percentages shift within your daily schedule will assist you
in obtaining an accurate trending of your body composition. It is recommended to use this unit in the
same environment and daily circumstances. Reference the chart below:
Daily activities
Waking up
Recommended time
Breakfast
2 hours
Recommended time
Lunch
2 hours
After waking up
Recommended time
Dinner
2 hours
Recommended time
Going to bed
About 2 hours or more after a meal
Avoid Taking Measurements Under the Following Conditions:
- Immediately after vigorous exercise, after a bath or sauna.
- After drinking alcohol or a large amount of water, after a meal (about 2 hours).
If a measurement is taken under these physical conditions, the calculated body composition may differ
significantly from the actual one because the water content in the body is changing.
12
Page 13
INFORMATION ON BODY COMPOSITION
Results may differ from actual body fat percentage
There are certain conditions when significant differences may occur between the estimated and the actual
body fat values. These differences may be related to changing ratios of body fluid and/or body
composition.
The body fat percentage measured by this monitor may significantly differ from the actual body fat
percentage for the following people:
• Elderly people
• People with a fever
• Body builders or highly trained athletes
• Persons undergoing dialysis
• Persons with osteoporosis who have very low bone density
•Pregnant women
• Persons with edema (swelling in the body)
• Children in growth stage
13
Page 14
Main Unit
SET/MODE Button
GUEST/ MEMO Button
Turns the power ON and
selects GUEST mode.
KNOW YOUR UNIT
Display
Err/OK/P Indicators
UPLOAD Button
Foot Electrodes
Components
Four AA Alkaline Batteries
Feet (
× 4)
Personal Profile Number Button
Turns the power ON and selects
body composition measurement.
Instruction Manual
Foot Electrodes
WEIGHT/OFF Button
Turns the power ON and
selects weight only
measurement.
ABOUT THE ALARM
The alarm will beep under the following conditions:
• When the power is turned on: Blip!
• When 0.0 lb is displayed and the unit is ready to take a measurement: Blip! Blip!
• When a measurement is completed: Blip, Beep!
• When the Err symbol appears: Blip! Blip! Blip! Blip! Blip! (A rapid series of short beeps.)
• When data has been sent successfully: Blip! Blip!
• When data failed to be sent: Beep! Beep! Beep! (A series of three long beeps.)
14
Page 15
Display
KNOW YOUR UNIT
Birth Date Indicator
Guest Indicator
Personal Profile Number
Date Indicator
Gender Indicator
Height Indicator
Delete Indicator
Wireless Communication
Indicator
Time Indicator
DATA Full Indicator
Low Battery Indicator
Age Indicator
Last Measurement Indicator
Weight Result/
Body Composition Results
Body Fat Percentage, Skeletal Muscle Percentage and
Visceral Fat Level Classification Bar
ABOUT AUTO POWER OFF FUNCTION
The power will be automatically turned off in the following conditions:
1. If the monitor is not used within one minute of 0.0 lb appearing on the display.
2. If no information is entered for three minutes when setting the date and time.
3. If no information is entered for three minutes when entering personal data.
4. If the monitor is not used for three minutes after the measurement results or last (previous)
measurement results are displayed.
5. 30 seconds after the result is displayed when measuring weight only.
6. 10 seconds after the Err symbol appears on the display.
NOTE: The OFF symbol appears on the display when the power is turned off.
Operating Instructions
15
Page 16
BATTERY INSTALLATION
1. Open the Battery Cover on the back of the
unit.
1) Press the tab on the battery cover in the
direction of the arrow to release the cover as
illustrated.
2) Pull the tab of the cover upwards.
2. Install 4 “AA” size alkaline batteries so the
+ (positive) and – (negative) polarities match
the polarities of the battery compartment as
indicated in the battery compartment.
3. Replace the battery cover.
1) Align the hooks on the battery cover with the
slots in the battery compartment.
Ta b
Back
2) Push the battery cover until the tab clicks into
place.
16
Page 17
BATTERY INSTALLATION
BATTERY REPLACEMENT
Measurement values and personal profiles stored in the memory will not be deleted during battery
replacement. However, the date and time will need to be set when monitor is turned back on.
Low Battery Indicator
When the Low Battery Indicator appears on the display screen, remove all four batteries.
Replace with four new batteries at the same time.
NOTE: New batteries will last for approximately six months (When AA alkaline batteries are used with
four measurements and data transfers a day at a room temperature of 23ºC).
Trial batteries supplied with the unit may have a shorter life.
WARNING:
If battery fluid should get in your eyes, immediately rinse with plenty of clean water. Contact your
physician immediately.
CAUTION:
If battery fluid should get on your skin or clothing, immediately rinse with plenty of clean water.
CAUTION:
Remove the batteries if the unit will not be used for three months or more.
CAUTION:
Dispose of the device, batteries, components and optional accessories according to applicable local
regulations. Unlawful disposal may cause environmental pollution.
17
Page 18
SETTING THE DATE AND TIME
Buttons Used in this Procedure
SET/MODE Button
Use this button to confirm the
setting and/or move to the next item
after confirming the set item.
1. Press the WEIGHT/OFF button to turn the monitor ON.
If this is the first time that the monitor has been turned on, the year
setting flashes.
GUEST/ MEMO Button
Press this button to advance one.
Press continuously to rapidly
advance.
SETTING THE YEAR
2.
1) Press the GUEST/ MEMO button to change the year.
2) Press the SET/MODE button.
The year is set.
The month flashes on the display.
SETTING THE MONTH
3.
1) Press the GUEST/ MEMO button to change the month.
2) Press the SET/MODE button.
The month is set.
The day flashes on the display.
18
Page 19
SETTING THE DATE AND TIME
SETTING THE DAY
4.
1) Press the GUEST/ MEMO button to change the day.
2) Press the SET/MODE button.
The day is set.
The hour flashes on the display.
SETTING THE HOUR
5.
1) Press the GUEST/ MEMO button to change the hour.
Make sure AM/PM is correct.
2) Press the SET/MODE button.
The hour is set.
The minute flashes on the display.
SETTING THE MINTUTE
6.
1) Press the GUEST/ MEMO button to change the minute.
2) Press the SET/MODE button.
The current settings for the year, month and day, hour and minute
appear in this sequence on the display. The monitor automatically turns off.
TO ADJUST THE DATE AND TIME
1) Press the WEIGHT/OFF button to turn the
monitor ON.
The current date appears on the display, then
the display changes to 0.0 lb.
2) Press the SET/MODE button for 2 seconds
or longer.
The year flashes on the display.
3) Refer to SETTING THE DATE AND
TIME on pages 18 and 19.
19
Page 20
SETTING PERSONAL DATA
To measure body composition, your personal data must be set. Your personal data includes your birth
date, gender and height. The monitor provides two options to enter your personal data.
1) Select a personal profile number to save your personal data. The monitor saves up to four personal
profiles. Select a number 1 through 4. Use this number to enter your personal data when taking a
measurement.
2) Select GUEST/ MEMO button if you do not want your personal data stored in the memory.
When you use the Guest mode you will need to enter your personal data each time you take a
measurement. Measurement results are not stored in the memory when the Guest mode is used.
Buttons Used in this Procedure
SET/MODE Button
Use this button to confirm the
personal data and/or move to the
next item after confirming the set
item.
GUEST/ MEMO Button
Press this button to advance one.
Press continuously to rapidly
advance.
Press this button to select Guest
mode.
1. Select a Personal Profile Number or the Guest mode.
A. Personal Profile Number
Press the desired Personal Profile Number
button (1 through 4).
The current date appears on the display, then
the display changes to the birth date (1940).
NOTE: When the date of birth, rather than current
date, is displayed, the settings for that
personal profile number are finished. Please
use a different number or delete your
personal profile information. Refer to
DELETING PERSONAL DATA on page
24.
B. Guest mode
Press the GUEST/ MEMO button.
The current date appears on the display, then the Guest indicator
appears and the birth year (1940) blinks on the display.
20
Page 21
SETTING PERSONAL DATA
2. Enter your Personal Data.
SETTING THE BIRTH DATE
Set the year between 1900 and 2030.
1) Press the GUEST/ MEMO button to change the birth year.
2) Press the SET/MODE button.
The birth year is set.
The birth month blinks on the display.
3) Press the GUEST/ MEMO button to change the birth
month.
4) Press the SET/MODE button.
The birth month is set.
The birth day blinks on the display.
5) Press the GUEST/ MEMO button to change
the birth day.
6) Press the SET/MODE button.
The birth day is set.
The gender symbols blink on the display.
SETTING THE GENDER
Set the gender to male or female.
1) Press the GUEST/ MEMO button to change the gender.
2) Press the SET/MODE button.
The gender is set.
The default value for height blinks on the display.
21
Page 22
SETTING PERSONAL DATA
SETTING THE HEIGHT
Set the height between 3' 4" and 6' 6 3/4".
(Display range in “cm” and “kg” display mode: 100.0 cm to 199.5 cm)
1) Press the GUEST/ MEMO button to change the height.
2) Press the SET/MODE button.
The height is set.
The current settings for birth date, age, gender and height appear in
this sequence on the display.
The 0.0 lb symbol appears on the display. You can now take a measurement using the Personal
Profile Number you selected or the Guest mode.
Refer to HOW TO TAKE A MEASUREMENT on pages 25 to 27.
SELECTING MEASUREMENT UNIT
You can change the measurement units used for the height and weight settings.
1. Press the WEIGHT/OFF button to turn the
monitor ON.
The current date appears on the display, then the
display changes to 0.0 lb.
Wait until 0.0 lb appears on the display.
2. Press and hold the GUEST/ MEMO
button until “lb” and “kg” blink on the display.
3.
Press the GUEST/ MEMO button to select the mode, “lb” or “kg”
This will also automatically change “cm” and “feet/inch” under height setting.
.
4. Press the SET/MODE button to confirm the change.
All height and weight measurements are displayed using the new measurement units. The change
remains in effect until you change it again.
22
Page 23
SETTING PERSONAL DATA
CHANGING PERSONAL DATA
If your personal data changes, the information in the Personal Profile Number you selected must be
changed for measurement results to be calculated correctly.
1. Press the Personal Profile Number button to
turn the monitor ON.
The birth date appears on the display, then the
display changes to 0.0 lb.
Wait until 0.0 lb appears on the display.
2. Press the SET/MODE button.
The current setting for birth year blinks on the display.
3. Refer to Step 2 on pages 21 and 22 to enter
your personal data.
23
Page 24
SETTING PERSONAL DATA
DELETING PERSONAL DATA
1. Press the Personal Profile Number button
you want to delete to turn the monitor ON.
The birth date appears on the display, then the
display changes to 0.0 lb.
Wait until 0.0 lb appears on the display.
2. Press the SET/MODE button.
The current setting for birth year blinks on the
display.
3. Press and hold the GUEST/ MEMO button until
the - - - - and DEL symbol blink on the display.
4. Press the SET/MODE button.
The DEL OK? symbol blinks on the display.
5. Press the SET/MODE button.
The Clr symbol appears on the display and the birth
year setting appears on the display.
NOTE: To cancel deleting, press the GUEST/
MEMO button.
6. Refer to Step 2 on pages 21 and 22 to set the new personal data or press the WEIGHT/
OFF button to turn the monitor off.
24
Page 25
HOW TO TAKE A MEASUREMENT
Measurement should be taken on level and hard surface.
1. Select a Personal Profile Number or the Guest mode.
A. Personal Profile Number
Press the Personal Profile Number button to
turn the monitor ON.
The birth date appears on the display, then
the display changes to 0.0 lb.
Wait until 0.0 lb appears on the display.
NOTES:
• If you step onto the monitor before 0.0 lb appears
on the display, an error message “Err” will
appear.
• If the following appears on the display, no
personal data was entered for the number you
selected.
Refer to SETTING PERSONAL DATA on
pages 21 and 22.
B. Guest mode
1) Press the GUEST/ MEMO button to turn the
monitor ON.
The current date appears on the display,
then the Guest indicator appears and the
birth year (1940) blinks on the display.
2) Enter your personal data. Refer to SETTING
PERSONAL DATA on pages 21 and 22.
25
Page 26
HOW TO TAKE A MEASUREMENT
2. Start the measurement.
1) Step on the unit bare-footed and place your feet on the foot electrodes with your weight evenly
distributed.
Remain still and do not move until your measurement is complete.
The display will show your
weight and then the weight
result will blink twice.
The monitor will start to
calculate body composition.
2) When the measurement is completed, your weight is
displayed again. Step off the unit.
During body composition
measurement, “ ” moves
to show the measurement
is progressing.
Postures to Avoid During Measurement
Incorrect posture may result in inaccurate measurement of body composition.
Standing on edge of the unit Knees bent Crouching
26
Page 27
HOW TO TAKE A MEASUREMENT
3. Check the measurement results.
The results display rotates automatically.
To stop the automatic rotation of results, or to view other measurement values, press the SET/
MODE button.
The display changes with each press of the SET/MODE button, as shown below.
NOTE: Use the bar indicator as a guide to measurement.
[WEIGHT] [BODY FAT PERCENTAGE]
Body Fat Percentage
Classification
[BODY AGE]
[VISCERAL FAT LEVEL]
Visceral Fat Level Classification
[BMI]
[SKELETAL MUSCLE PERCENTAGE]
Skeletal Muscle Percentage Classification
[RESTING METABOLISM]
4. Press the WEIGHT/OFF button to turn the monitor off.
27
Page 28
UNDERSTANDING YOUR MEASUREMENT RESULTS
Interpreting the BMI Result
BMI BMI (Designation by the WHO)
Less than 18.5 Underweight
18.5 or more and less than 25 Normal
25 or more and less than 30 Overweight
30 or more Obese
Source: Values for obesity judgment proposed by WHO, the World Health Organization.
Interpreting the Body Fat Percentage Result
The table below is based on research by Gallagher et al., American Journal of Clinical Nutrition, Vol. 72,
Sept. 2000, and classified into four levels by Omron Healthcare.
Gender Age – (Low) 0 (Normal) + (High) ++ (Very High)
_
_
>
39.0%
_
_
>
40.0%
_
_
>
42.0%
_
_
>
25.0%
_
_
>
28.0%
_
_
>
30.0%
Female
Male
20-39
40-59
60-80
20-39
40-59
60-80
< 21.0% 21.0 - 32.9% 33.0 - 38.9%
< 23.0% 23.0 - 33.9% 34.0 - 39.9%
< 24.0% 24.0 - 35.9% 36.0 - 41.9%
< 8.0% 8.0 - 19.9% 20.0 - 24.9%
< 11.0% 11.0 - 21.9% 22.0 - 27.9%
< 13.0% 13.0 - 24.9% 25.0 - 29.9%
Interpreting the Skeletal Muscle Percentage Result (for adults)
Gender Age – (Low) 0 (Normal) + (High) ++ (Very High)
_
_
>
_
_
>
_
_
>
_
_
>
_
_
>
_
_
>
Female
Male
18-39 < 24.3% 24.3 - 30.3% 30.4 - 35.3%
40-59 < 24.1% 24.1 - 30.1% 30.2 - 35.1%
60-80 < 23.9% 23.9 - 29.9% 30.0 - 34.9%
18-39 < 33.3% 33.3 - 39.3% 39.4 - 44.0%
40-59 < 33.1% 33.1 - 39.1% 39.2 - 43.8%
60-80 < 32.9% 32.9 - 38.9% 39.0 - 43.6%
Source: Omron Healthcare
Interpreting the Visceral Fat Level Result
_
_
Visceral Fat Level 9
<
0 (Normal)
_
_
<
10 Visceral Fat Level 14
_
_
<
+ (High)
Visceral fat area (0 - approx. 300 cm2, 1 inch=2.54 cm) distribution with 30 levels.
Source: Omron Healthcare
NOTE: Visceral fat levels are relative and not absolute values.
Visceral Fat Level 15
++ (Very High)
_
_
>
35.4%
35.2%
35.0%
44.1%
43.9%
43.7%
28
Page 29
HOW TO MEASURE WEIGHT ONLY
1. Press the WEIGHT/OFF button to turn the
monitor ON.
The current date appears on the display, then the
display changes to 0.0 lb.
Wait until 0.0 lb appears on the display.
NOTES:
• If you step onto the monitor before 0.0 lb appears
on the display, an error message “Err” will appear.
• You can change the measurement units used for
the height and weight settings. Personal data and
measurement results in memory will be displayed
by selected setting. To change the measurement unit:
1) Keep the GUEST/ MEMO button pressed until “lb” and “kg” blink on the display.
2) Press the GUEST/ MEMO button to select the desired measurement unit, “lb” or “kg”.
This will automatically change “cm” and “feet/inch” under height setting
3) Press the SET/MODE button to confirm the change.
2. Step onto the unit.
Stand with your weight evenly distributed on the measurement
platform.
Remain still and do not move until the measurement is
complete.
3. Check the measurement result.
The display will show your weight and then the weight result
will blink twice.
.
4. Step off the unit.
5. Press the WEIGHT/OFF button to turn the monitor off.
29
Page 30
VIEWING THE LAST MEASUREMENT RESULTS
Up to 30 measurement results are automatically stored for each personal profile number and the last
(previous) measurement results can be displayed for this unit.
When using GUEST mode, the measurement results are not stored so you cannot see the last (previous)
measurement results.
Buttons Used in this Procedure
SET/MODE Button
Press this button to cycle through
the last (previous) measurement
values.
GUEST/ MEMO Button
Press this button to display the last
(previous) weight value and
alternate between the current
measurement result and the last
measurement result.
1. Press the Personal Profile Number button to
turn the monitor ON.
2. Take a measurement.
If you want to compare the results with the last
(previous) values, measure your body composition.
3. Press the GUEST/ MEMO button.
The last weight value is displayed.
If you have measured your body composition in step 2, each press of
the GUEST/ MEMO button alternates between the current
measurement result and the last (previous) result.
NOTES:
• If there are no results for the last measurement, the
• If you have not measured your body composition in step 2, current measurement results cannot be
displayed even if you press the GUEST/ MEMO button.
- - - - symbol is displayed.
30
Page 31
VIEWING THE LAST MEASUREMENT RESULTS
4. Press the SET/MODE button to cycle through the other measurement values.
Last weight
Last body age
Last BMI
Last skeletal muscle
percentage
Last body fat percentage
Last visceral fat level
Last resting metabolism
NOTE: Refer to TRANSFERRING THE DATA on pages 32 to 34 if you want to transfer the data.
5. Press the WEIGHT/OFF button to turn the monitor off.
31
Page 32
TRANSFERRING THE DATA
You can transfer measurement data to a Bluetooth® wireless technology device.
You can transfer up to 30 sets of stored measurement results for each personal profile number.
The content and display for the measurement results may vary depending on the application used to view them.
For details, refer to the manual provided with the application you are using.
Buttons Used in this Procedure
UPLOAD button
Press this button to transfer the data
to a Bluetooth
device.
Press and hold to register a
destination device.
®
wireless technology
REGISTERING THE UNIT WITH THE DESTINATION DEVICE (PAIRING)
What is Pairing:
This refers to the procedure for registering the unit with the device so that it can be used to transfer data.
Pairing is required when a device is connected to the unit for the first time, or if the same device is used
to transfer data for a different personal profile number.
Follow the procedure below to pair the unit with the destination device.
Refer to TRANSFERRING THE DATA on page 33 for information about transferring the data with a
device that has already been paired with the unit.
1. Display the measurement results.
Pairing (Registration) after taking a measurement:
Refer to HOW TO TAKE A MEASUREMENT on page 25, to display the
measurement results.
Pairing (Registration) without taking a measurement:
Refer to VIEWING THE LAST MEASUREMENT RESULTS on page
30, to display the results for the last measurement.
Pairing (Registration) when using GUEST mode:
You can also start pairing after taking a measurement using GUEST mode.
Refer to HOW TO TAKE A MEASUREMENT on page 25, to display the measurement results.
2. Enable pairing (registration) on the device.
Set the application on the device ready for pairing.
For details, refer to the manual provided with the application you are using.
32
Page 33
TRANSFERRING THE DATA
3. Press the UPLOAD button for 2 seconds or longer.
Use the application to pair the unit with the device.
For details, refer to the manual provided with the application you are
using.
NOTE: If you press the UPLOAD button while pairing, pairing will be
stopped and the display will revert to the previous screen.
If the pairing completes successfully, the P indicator lights and the
alarm will beep (Blip! Blip!).
NOTES:
• If the pairing process does not complete within approximately one
minute, it will end without paring the unit with the device.
• If the pairing process does not complete successfully, then the Err
indicator lights and the alarm will beep three times (Beep! Beep!
Beep!).
Check the application on the connected device, then repeat the
procedure from step 2 to try again.
TRANSFERRING THE DATA
1. Display the measurement results.
Transferring data after taking a measurement:
Refer to HOW TO TAKE A MEASUREMENT on page 25, to display
the measurement results.
Transferring data without taking a measurement:
Refer to VIEWING THE LAST MEASUREMENT RESULTS on
page 30, to display the results for the last measurement.
Transferring data when using GUEST mode:
You can also register a device after taking a measurement using GUEST mode.
Refer to HOW TO TAKE A MEASUREMENT on page 25, to display the measurement results.
NOTE: When using GUEST mode, you cannot send results stored on the unit, you can only send
the measurement results for the current measurement.
2. Enable data transfers.
Set the application on the destination device to transfer mode.
For details, refer to the manual provided with the application you are using.
33
Page 34
TRANSFERRING THE DATA
3. Press the UPLOAD button.
The display changes to the data transmission screen, and the unit starts
transferring the data.
If the data is sent successfully, the OK indicator lights and the alarm
will beep (Blip! Blip!).
NOTES:
• If you press the UPLOAD button while the data is being
transferred, the transfer will be stopped and the display will revert
to the previous screen.
• If the data transmission fails, then the Err indicator lights and the
alarm will beep three times (Beep! Beep! Beep!). Check the
application on the connected device, then repeat the procedure from
step 2 to try again.
4. Press the WEIGHT/OFF button to turn the monitor off.
NOTE: If you forget to turn the monitor off, the screen will return to the screen displayed before
data transmission started after 10 seconds.
About Data FULL Indicator
Up to 30 sets of measurement results can be stored for each personal
profile number.
If the number exceeds 30, the oldest results are deleted.
If the Data FULL indicator blinks or remains lit, transfer data to a device
as soon as possible to avoid losing measurement results.
blinks: 24-29 sets of measurement results have been stored.
lit: 30 sets of measurement results have been stored.
NOTE: The Data FULL indicator is not displayed when only 0 to 23 measurements results are stored.
DATA FULL
Indicator
34
Page 35
ABOUT THE WIRELESS COMMUNICATIONS FUNCTION
CAUTION:
To maintain compliance with FCC’s RF exposure guidelines, use only the supplied antenna.
Unauthorize antenna, modification, or attachments could damage the transmitter and may violate
FCC regulations.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may Cause
undesired operation.
This Product operates in the unlicensed ISM band at 2.4GHz. In case this Product is used
around the other wireless devices including microwave oven and wireless LAN, which
operate same frequency band of this Product, there is a possibility that interference occurs
between this Product and such other devices. If such interference occurs, please stop the
operation of other devices or relocate this Product before using this Product or do not use
this Product around the other wireless devices.
The Bluetooth
Inc. and any use of such marks by Omron Healthcare Co.,Ltd. is under license. Other
trademarks and trade names are those of their respective owners.
Look for the Continua Certified logo. It’s your assurance that a device will reliably
communicate and exchange information with similarly certified products, to help you
better manage your health and wellness.
®
word mark and logos are registered trademarks owned by Bluetooth SIG,
Care and Maintenance
35
Page 36
ERROR INDICATORS
ERROR
DISPLAY
CAUSE CORRECTION
Your feet are not positioned over
the electrodes correctly.
The measurement position was not
stable.
Your feet were not placed correctly.
Your feet are too dry.
Make sure you are barefoot.
Make sure your soles of your feet are clean and
dry.
Make sure your feet are correctly positioned.
Refer to POSTURES TO AVOID DURING
MEASUREMENT on page 26.
Remain still and do not move until the
measurement is complete.
Refer to POSTURES TO AVOID DURING
MEASUREMENT on page 26.
Slightly moisten your soles of your feet with a
damp towel and retake the measurement.
Turn the monitor off, and on again. Take the
Device error.
You stepped onto the measurement
platform before 0.0 lb was
displayed.
The monitor was moved before
0.0 lb was displayed.
Movement during measurement. Do not move until measurement is complete.
Monitor detected weight over
330.0 lb.
measurement.
If this error still occurs, consult your OMRON
service representative.
Wait until 0.0 lb is displayed before stepping
onto the measurement platform.
Do not move the monitor until 0.0 lb is
displayed.
This monitor can only be used by people
weighing less than 330.0 lb.
36
Page 37
TROUBLESHOOTING TIPS
Problem Cause Correction
0.0 lb is displayed even when
you step onto the unit, or the
weight value barely increases.
The value of body weight is
displayed abnormally high or low.
The body composition value is
displayed abnormally high or
low.
The body composition values
vary widely for each
measurements.
“- - - -” is displayed for some
of the results.
Nothing is displayed when the
power is turned on.
You stepped onto the unit before
0.0 lb was displayed.
Your posture is not correct during
measurement.
Is the unit placed on a carpet or
other soft flooring?
Is the floor surface is uneven?
The soles of your feet, or whole
body are cold, causing poor blood
circulation.
The electrodes are extremely
cold.
Feet are too dry.
The personal data settings or body
composition values are outside
the measurable range.
Batteries are not inserted.
The polarities of batteries are not
aligned correctly.
The batteries are worn out.
Wait until 0.0 lb is displayed
before stepping onto the unit.
Stand still in the correct posture to
take a measurement.
Refer to POSTURES TO AVOID
DURING MEASUREMENT on
page 26.
Place the unit on a hard and level
floor.
Warm yourself up, then take a
measurement once you feel your
circulation is back to normal.
Place the unit in a warm room for
a few minutes, and then take a
measurement when the electrodes
no longer feel cold.
Slightly moisten the soles of your
feet with a damp towel and try again.
Check that the Birth Date,
Gender, and Height settings are
correct.
Even if the Birth Date, Gender,
and Height settings are correct,
measurements cannot be taken if
they are outside the measurable
range.
Check that the settings are within
the measurable range.
Refer to SPECIFICATIONS on
page 42.
Insert the batteries.
(Refer to BATTERY
INSTALLATION on page 16.)
Insert the batteries in correct
alignment. (Refer to BATTERY
INSTALLATION on page 16.)
Replace all four batteries with
new ones. (Refer to BATTERY
INSTALLATION on page 16.)
37
Page 38
TROUBLESHOOTING TIPS
Problem Cause Correction
You want to measure your
body composition, but body
composition measurement
does not start after the weight
measurement has been
displayed.
Data cannot be sent.
(Err indicator lights.)
The power is automatically
turned off.
A personal data for a Personal
Profile Number or Guest mode
measurement has not been set.
(Neither a Personal Profile
Number 1, 2, 3, 4 or Guest is
displayed.)
The Personal Profile Number
button or GUEST/ MEMO
button was not pressed correctly.
(Neither a Personal Profile
Number 1, 2, 3, 4 or Guest is
displayed.)
The destination device for the
data is too far away.
Pairing (registering) has not been
completed.
The application on the connected
device is not ready.
Refer to ABOUT AUTO POWER OFF FUNCTION on page 15.
Enter a personal data for a
Personal Profile Number or use
Guest mode.
Refer to SETTING PERSONAL
DATA on page 20.
Make sure that Personal Profile
Number 1, 2, 3, 4 or Guest is
displayed before measurement.
Refer to HOW TO TAKE A
MEASUREMENT on page 25.
After checking that there are no
sources of interference nearby,
move the device to a distance
within 5 m of the unit.
Perform pairing (registration).
Refer to REGISTERING THE
UNIT WITH THE
DESTINATION DEVICE
(PAIRING) on page 32.
Check the application then try
sending the data again.
If the Err indicator still lights after
checking the application, contact
the service (support) center of the
application provider.
38
Page 39
CARE AND MAINTENANCE
To keep your Bluetooth® Body Composition Monitor in the best condition and protect the monitor from
damage follow the directions below:
Clean the monitor with a soft dry cloth. Do not use abrasive or volatile cleaners. The monitor is not
waterproof.
Store the monitor in a safe and dry location. Do not expose the monitor to direct sunlight, extreme hot
or cold temperatures or humidity. Thoroughly dry any moisture off the monitor before storing.
CAUTION:
Do not submerge the device or any of the components in water.
CAUTION:
Do not subject the monitor to strong shocks, such as dropping the unit on the floor.
Remove the batteries if the monitor will not be used for three months or longer.
Use the monitor consistent with the instruction provided in this manual.
CAUTION:
Do not disassemble or modify the unit. Changes or modifications not approved by Omron
Healthcare will void the user warranty.
39
Page 40
FCC STATEMENT
NOTE:
POTENTIAL FOR RADIO/TELEVISION INTERFERENCE (for U.S.A. only)
This product has been tested and found to comply with the limits for a Class B digital device, pursuant to
part 15 of the FCC rules.
These limits are designed to provide reasonable protection against harmful interference in a residential
installation. The product generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If the product
does cause harmful interference to radio or television reception, which can be determined by turning the
product on and off, the user is encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the product and the receiver.
• Connect the product into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
POTENTIAL FOR RADIO/TELEVISION INTERFERENCE (for Canada only)
This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus
as set out in the interference-causing equipment standard entitled “Digital Apparatus”, ICES-003 of the
Canadian Department of Communications.
Cet appareil numérique respecte les limites de bruits radioélectriques applicables aux appareils
numériques de Classe B prescrites dans la norme sur le matériel brouilleur: “Appareils Numériques”,
ICES-003 édictée par le ministère des communications.
Changes or modifications not expressly approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
40
Page 41
WARRANTY
Limited Warranty
Your HBF-206IT Bluetooth® Body Composition Monitor, excluding the batteries, is warranted to be free
from defects in materials and workmanship appearing within 1 year from the date of purchase, when
used in accordance with the instructions provided with the unit. The above warranties extend only to the
original retail purchaser.
We will, at our option, repair or replace without charge any monitor covered by the above warranties.
Repair or replacement is our only responsibility and your only remedy under the above warranties. To
obtain warranty service contact Omron Healthcare’s Customer Service by calling 1-800-634-4350 for
the address of the repair location and the return shipping and handling fee. Information for warranty
service is available on our website at www.omronhealthcare.com.
Enclose the Proof of Purchase. Include a letter, with your name, address, phone number, and description
of the specific problem. Pack the product carefully to prevent damage in transit. Because of possible loss
in transit, we recommend insuring the product with return receipt requested.
THE FOREGOING IS THE SOLE WARRANTY PROVIDED BY OMRON IN CONNECTION
WITH THIS PRODUCT, AND OMRON HEREBY DISCLAIMS ANY OTHER WARRANTIES,
EXPRESS OR IMPLIED, INCLUDING IMPLIED WARRANTIES OF MERCHANTABILITY
AND FITNESS FOR A PARTICULAR PURPOSE. IMPLIED WARRANTIES AND OTHER
TERMS THAT MAY BE IMPOSED BY LAW, IF ANY, ARE LIMITED IN DURATION TO THE
PERIOD OF THE ABOVE EXPRESS WARRANTY.
OMRON SHALL NOT BE LIABLE FOR LOSS OF USE OR ANY OTHER SPECIAL,
INCIDENTAL, CONSEQUENTIAL OR INDIRECT COSTS, EXPENSES OR DAMAGES.
This warranty provides you with specific legal rights, and you may have other rights that vary by
jurisdiction. Because of special local requirements, some of the above limitations and exclusions may
not apply to you.
FOR CUSTOMER SERVICE
Visit our web site at: www.omronhealthcare.com
For service related to device, call toll free: 1-800-634-4350
For service related to wireless Contact Home Health
communications to home health device: Device Service Provider.
41
Page 42
SPECIFICATIONS
Model HBF-206IT (HBF-206IT-Z)
Display Body Weight: 0 to 330 lb with 0.2 lb increments
(0 to 150 kg with 0.1 kg increments)
Body fat percentage: 5.0 to 60.0% with 0.1% increments
Skeletal muscle percentage: 5.0 to 50.0% with 0.1% increments
BMI: 7.0 to 90.0 with 0.1 increments
Resting metabolism: 385 to 3999 kcal with 1 kcal increments
Body age: 18 to 80 years old with 1 year increments
Visceral fat level: 30 levels with 1 level increments
Body fat percentage and Skeletal muscle percentage classification:
– (Low) / 0 (Normal) / + (High) / ++ (Very High) 4 levels with 3 sublevels each
Visceral fat classification:
0 (Normal) / + (High) / ++ (Very High) 3 levels with 3 sublevels each
* The age range for the Body Fat Percentage is 10 to 80 years old.
* The age range for the Skeletal Muscle Percentage, Skeletal Muscle
Percentage Classification, Resting Metabolism rate, Visceral Fat Level,
Visceral Fat Level Classification and Body age is 18 to 80 years old.
* The age range for the Body Fat Percentage Classification is 20 to 80 years
old.
Memory Display memory: Last (previous) measurement results
Unit stored memory: Up to 30 sets
Transmission protocol
Set Ranges Personal data Information:
Power Supply 4 AA alkaline batteries
Battery Life Approximately 6 months (When AA alkaline batteries are used with four
Operating Temperature
/Humidity
Storage Temperature
/Humidity/Air Pressure
External Dimensions Approximately 11 3/4" (W) x 1 1/2" (H) x 11 3/8" (D)
Weight Approximately 4 lb (including batteries)
Contents Body Composition Monitor, 4 AA Alkaline Batteries, Instruction Manual
Bluetooth® wireless technology Version 2.1 + EDR Class 2
The following information for up to 4 people can be stored.
Height: 3' 4" to 6' 6 3/4" (100.0 to 199.5 cm)
Birth Date: January 1st, 1900 to December 31st, 2030
Gender: Male/Female
measurements and data transfers a day at a room temperature of 23ºC.)
+50°F to +104°F (+10°C to +40°C), 30 to 85% RH
–4°F to +140°F (–20°C to +60°C), 10 to 95% RH, 700 - 1060 hPa
NOTE: Specifications are subject to change without prior notice.
42
Page 43
NOTES
43
Page 44
Distributed by:
Omron Healthcare, Inc.
1200 Lakeside Drive
Bannockburn, Illinois 60015
www.omronhealthcare.com
Copyright © 2010 Omron Healthcare, Inc.
Made in China
5328803-5B
Loading...