OMRON H7CX Technical data

查询H7CX-A供应商

Multifunction Preset Counter

H7CX

• Highly visible display with backlit negative transmissive LCD.

• Programmable PV color to visually alert when output status changes (screw terminal block models).

• Intuitive setting enabled using ergonomic up/down digit keys (4digit models) and DIP switch.

• Configurable as 1-stage counter, 2-stage counter, total and preset counter, batch counter, dual counter, or tachometer. (Configurability varies with model.)

• PNP/NPN switchable input.

• Finger-safe terminals (screw terminal block models).

• Meets a variety of mounting requirements: Screw terminal block models, and pin-style terminal models.

• NEMA4/IP66 compliance.

• Six-language instruction manual.

Contents

Model Number Structure.............................................................. C-88

Ordering Information.................................................................... C-88

Specifications............................................................................... C-89

Connections................................................................................. C-93

Nomenclature .............................................................................. C-98

Dimensions .................................................................................. C-99

Precautions.................................................................................. C-103

Operating Procedures.................................................................. C-106

Setting Procedure Guide ....................................................... C-106

Operating Procedures (Counter Function) ............................ C-107

Operating Procedures (Tachometer Function) ...................... C-118

Operation in Configuration Selection Mode........................... C-124

Additional Information .................................................................. C-125

Counters

Multifunction Preset Counter

H7CX

C-87

Model Number Structure

Model Number Legend

■

H7CX-A@@@@@@

1 2 3 4 5 6

1. External connection

None: Screw terminals 11: 11-pin socket

2. No. of digits

None: 6 digits 4: 4 digits

3. Stage setting

None: 1-stage setting U: Factory-set to 1-stage setting W: Factory-set to 2-stage setting

Ordering Information

List of Models

■

4. Output type

None: Contact output or contact and transistor in combination S: Transistor output

5. Supply voltage/external power supply

None: 100 to 240 VAC at 50/60 Hz with 12 VDC power supply D: 12 to 24 VDC without external power supply D1: 12 to 24 VDC or 24 VAC at 50/60 Hz with 12 VDC power

supply

6. Case color

None: Black G: Light gray (Munsell 5Y7/1): Produced upon request.

Supported configurations •

Sensor

power

supply

12 VDC Contact output 100 to 240 VAC H7CX-A11 H7CX-A114 H7CX-A H7CX-A4 --- H7CX-AW H7CX-A4W

None Contact output 12 to 24 VDC --- --- H7CX-AD H7CX-A4D --- --- ---

Note:

■

Flush Mounting Adapter (See note 1.) Y92F-30

Waterproof Packing (See note 1.) Y92S-29

Track Mounting/Front Connecting Socket

Back Connecting Socket 11-pin P3GA-11

Hard Cover Y92A-48

Soft Cover Y92A-48F1

Mounting Track 50 cm (l) × 7.3 mm (t) PFP-50N

End Plate PFP-M

Spacer PFP-S

Note: 1.

Output type Supply voltage 11-pin socket Screw terminal

12 to 24 VDC/ 24 VAC

Contact and transistor output

Transistor output 100 to 240 VAC H7CX-A11S H7CX-A114S H7CX-AS H7CX-A4S --- H7CX-AWS ---

Transistor output --- --- H7CX-ASD H7CX-A4SD --- H7CX-AWSD H7CX-A4WSD

100 to 240 VAC --- --- --- --- H7CX-AU --- ---

12 to 24 VDC/ 24 VAC

Can be used as a 2-stage counter. In this case, each output can be flexibly allocated to either stage 1 or 2.

Accessories (Order Separately)

Name Models

11-pin P2CF-11

11-pin, finger-safe type P2CF-11-E

11-pin, finger-safe type P3GA-11 with Y92A-48G (See note 2.)

1 m (l) × 7.3 mm (t) PFP-100N

1 m (l) × 16 mm (t) PFP-100N2

Supplied with screw-terminal models (i.e., excluding H7CX-A11@/-A114@ models). Y92A-48G is a finger-safe terminal cover attached to the P3GA-11 Socket.

1-stage counter

•

1-stage counter with total counter

1-stage 1-stage

6 digits 4 digits 6 digits 4 digits 6 digits 6 digits 4 digits

H7CX-A11

H7CX-A11D1 H7CX-A114D1 --- --- --- H7CX-AWD1 ---

--- --- --- --- H7CX-AUD1 --- ---

H7CX-A11SD1 --- --- --- H7CX-AUSD1 H7CX-AWSD1 ---

H7CX-A114@H7CX-A@H7CX-A4@H7CX-AU

•

1-stage counter

•

2-stage counter

•

1-stage counter with total counter

•

1-stage counter with batch counter

•

Dual counter (addition/subtraction)

•

Tachometer

(See note.)

H7CX-AW

•

1-stage counter

•

2-stage counter

•

1-stage counter with total counter

•

1-stage counter with batch counter

•

Dual counter (addition only)

2-stage

H7CX-A4W

C-88

Multifunction Preset Counter

H7CX

Specifications

Ratings

■

Item H7CX-A4

Classification

Supported configurations

Rated supply voltage (See note 1.)

Operating voltage range

Power consumption

Mounting method

External connections

Terminal screw tightening torque

Display

Digits

Max. counting speed

Input modes

Input signals

Input method

Reset input

Reset system

Output modes

One-shot output time

Output type

Control output

External power supply

Key protection

Prescaling function

Decimal point adjustment

Sensor waiting time

Memory backup

Ambient temperature

Ambient humidity

Case color

Attachments

Note: 1.

Permissible ripple: 20% (p-p) max. Only when the following modes are selected.

Input mode: command, individual, or quadrature; output mode: K-2, D, or L

Preset counter

1-stage counter, 1-stage counter with total counter (selectable)

100 to 240 VAC (50/60 Hz), 12 to 24 VDC 100 to 240 VAC (50/60 Hz)

85% to 110% of rated supply voltage (90% to 110% at 12 VDC)

Approx. 9.2 VA at 264 VAC Approx. 7.2 VA at 26.4 VAC Approx. 3.7 W at 12 VDC

Flush mounting Flush mounting, surface mounting, or DIN track mounting

Screw terminals 11-pin socket

0.5 N·m max. ---

7-segment, negative transmissive LCD;

11.5-mm-high characters, red or green (programmable)

6-mm-high characters, green

4 digits (−999 to 9,999) SV range: 0 to 9,999

30 Hz or 5 kHz (selectable, ON/OFF ratio 1:1), common setting for CP1 and CP2

Increment, decrement, command, individual, and quadrature

CP1, CP2, reset, and total reset

No-voltage input/voltage input (switchable) No-voltage input ON impedance: 1 kΩ max. (Leakage current: 5 to 20 mA at 0 Ω) ON residual voltage: 3 V max. OFF impedance: 100 kΩ min. Voltage input High (logic) level: 4.5 to 30 VDC Low (logic) level: 0 to 2 VDC (Input resistance: approx. 4.7 kΩ)

Minimum reset input signal width: 1 or 20 ms (selectable), common setting for all inputs

External, manual, and automatic reset (internal according to C, R, P, and Q mode operation)

N, F, C, R, K-1, P, Q, A N, F, C, R, K-1, P, Q, A,

0.01 to 99.99 s

Contact type: SPDT Transistor type: 1 transistor

Contact output: 3 A at 250 VAC/30 VDC, resistive load (cosφ=1) Minimum applied load: 10 mA at 5 VDC (failure level: P, reference value) Transistor output: NPN open collector, 100 mA at 30 VDC

NEMA B300 Pilot Duty, 1/4 HP 3-A resistive load at 120 VAC, 1/3 HP 3-A resistive load at 240 VAC

12 VDC (±10%), 100 mA (except for H7CX-A@D models) Refer to

Precautions

Ye s

Yes (0.001 to 9.999) Yes (0.001 to 99.999) Yes (0.001 to 9.999) Yes (0.001 to 99.999)

Yes (rightmost 3 digits)

250 ms max. (Control output is turned OFF and no input is accepted during sensor waiting time.)

EEPROM (overwrites: 100,000 times min.) that can store data for 10 years min.

Operating:−10 to 55°C (−10 to 50°C if counters are mounted side by side) (with no icing or condensation) Storage:−25 to 65°C (with no icing or condensation)

25% to 85%

Black (N1.5), light gray (Munsell 5Y7/1, produced upon request)

Waterproof packing, flush mounting adapter None

for details.

9-mm-high characters, red or green (programmable)

6 digits (−99,999 to 999,999) SV range: −99,999 to 999,999 (See note 2.) or 0 to 999,999

K-2, D, L

Residual voltage: 1.5 VDC max. (approx. 1 V) Leakage current: 0.1 mA max.

H7CX-A

H7CX-A114

24 VAC (50/60 Hz)/12 to 24 VDC

11.5-mm-high characters, red 9-mm-high characters, red

4 digits (−999 to 9,999) SV range: 0 to 9,999

N, F, C, R, K-1, P, Q, A N, F, C, R, K-1, P, Q, A,

6 digits (−99,999 to 999,999) SV range: −99,999 to 999,999 (See note 2.) or 0 to 999,999

K-2, D, L

H7CX-A11

Counters

Multifunction Preset Counter

H7CX

C-89

Ratings (contd.)

■

Classification

Supported configurations

Rated supply voltage (See note 1.)

Operating voltage range

Power consumption

Mounting method

External connections

Terminal screw tightening torque

Display

Digits

Input signals

Input method

Counter Max. counting speed

Tachometer Pulse measurement

Output type

Control output

External power supply

Key protection

Prescaling function

Decimal point adjustment

Sensor waiting time

Memory backup

Ambient temperature

Ambient humidity

Case color

Attachments

Item H7CX-A4W@ H7CX-AW@ H7CX-AU@

Input mode

Reset input

Reset system

Output modes

One-shot output time

method

Max. counting speed

Measuring ranges

Measuring accuracy

Output modes

Auto-zero time

Startup time

Average processing

Preset counter Preset counter/tachometer

1-stage counter, 2-stage counter, 1-stage counter with total counter, 1-stage counter with batch counter, dual counter (addition only) (selectable)

100 to 240 VAC (50/60 Hz), 12 to 24 VDC

85% to 110% of rated supply voltage (90% to 110% at 12 VDC)

Approx. 9.2 VA at 264 VAC Approx. 7.2 VA at 26.4 VAC Approx. 3.7 W at 12 VDC

Flush mounting

Screw terminals

0.5 N·m max.

7-segment, negative transmissive LCD

11.5-mm-high characters, red or green (programmable)

6-mm-high characters, green

4 digits (−999 to 9,999) SV range: 0 to 9,999

CP1, CP2, reset 1, and reset 2

30 Hz or 5 kHz (selectable, ON/OFF ratio 1:1), common setting for CP1 and CP2

Increment, decrement, command, individual, and quadrature

Minimum reset input signal width: 1 or 20 ms (selectable), common setting for all inputs

External, manual, and automatic reset (internal according to C, R, P, and Q mode operation)

N, F, C, R, K-1, P, Q, A N, F, C, R, K-1, P, Q, A, K-2, D, L, H

0.01 to 99.99 s

--- Periodic measurement (Sampling period: 200 ms)

--- 30 Hz or 10 kHz (selectable)

--- 30 Hz: 0.01 to 30.00 Hz

---

--- HI-LO, AREA, HI-HI, LO-LO

--- 0.1 to 99.9 s

--- 0.0 to 99.9 s

--- OFF/2/4/8 times

H7CX-A4W/-AW/-AWD1: SPDT (OUT2) and SPST-NO (OUT1) H7CX-A4WSD/-AWS/-AWSD/-AWSD1: 2 transistors

Contact output: 3 A at 250 VAC/30 VDC, resistive load (cosφ=1) Minimum applied load: 10 mA at 5 VDC (failure level: P, reference value) Transistor output: NPN open collector, 100 mA at 30 VDC

NEMA B300 Pilot Duty, 1/4 HP 3-A resistive load at 120 VAC, 1/3 HP 3-A resistive load at 240 VAC

12 VDC (±10%) 100 mA (except for H7CX-A@D models) Refer to

Precautions

Ye s

Yes (0.001 to 9.999) Yes (0.001 to 99.999)

Yes (rightmost 3 digits)

250 ms max. (Control output is turned OFF and no input is accepted during sensor waiting time.)

EEPROM (overwrites: 100,000 times min.) that can store data for 10 years min.

Operating:−10 to 55°C (−10 to 50°C if counters are mounted side by side) (with no icing or condensation) Storage:−25 to 65°C (with no icing or condensation)

25% to 85%

Black (N1.5), light gray (Munsell 5Y7/1, produced upon request)

Waterproof packing, flush mounting adapt-erWaterproof packing, flush mounting adapter, labels for counter/tachometer DIP switch settings

Residual voltage: 1.5 VDC max. (approx. 1 V) Leakage current: 0.1 mA max.

for details.

1-stage counter, 2-stage counter, 1-stage counter with total counter, 1-stage counter with batch counter, dual counter (addition/subtraction), tachometer (selectable)

100 to 240 VAC (50/60 Hz), 24 VAC (50/60 Hz)/12 to 24 VDC, 12 to 24 VDC

9-mm-high characters, red or green (programmable)

6 digits (−99,999 to 999,999 or 0 to 999,999 when using as Tachometer) SV range: −99,999 to 999,999 (See note 2.) or 0 to 999,999

10 kHz: 0.01 Hz to 10 kHz

0.1% FS ±1 digit max. (at 23 ±5°C)

100 to 240 VAC (50/60 Hz), 24 VAC (50/60 Hz)/12 to 24 VDC

H7CX-AU/-AUD1: SPDT and 1 transistor H7CX-AUSD1: 2 transistors (Output allocation possible)

Note: 1.

C-90

Permissible ripple: 20% (p-p) max. Only when the following modes are selected.

- Input mode: command, individual, or quadrature; output mode: K-2, D, L, or H

- Dual count calculating mode: SUB; output mode: K-2, D, L, or H in dual counter operation

Multifunction Preset Counter

H7CX

Characteristics

■

item H7CX

Insulation resistance

Dielectric strength

Impulse withstand voltage

Noise immunity

Static immunity

Vibration resistance

Shock resistance

Life expectancy

Approved safety standards (See note 1.)

EMC

Degree of protection

Weight

Note: 1.

To meet UL listing requirements with the H7CX-A11@ models, an OMRON P2CF-11-@ or P3GA-11 Socket must be mounted on the H7CX. Otherwise, H7CX-A11@ models are considered to meet UL508 recognition requirements.

A waterproof packing is necessary to ensure IP66 waterproofing between the H7CX and installation panel.

100 MΩ min. (at 500 VDC) between current-carrying terminal and exposed non-current-carrying metal parts, and between non-continuous contacts

2,000 VAC, 50/60 Hz for 1 min between current-carrying metal parts and non-current-carrying metal parts 2,000 VAC (for 100 to 240 VAC), 50/60 Hz for 1 min between power supply and input circuit (1,000 VAC for 24 VAC/ 12 to 24 VDC) 1,000 VAC (for H7CX-@SD/-@SD1), 50/60 Hz for 1 min between control output, power supply, and input circuit (2,000 VAC for models other than H7CX-@SD/-@SD1) 1,000 VAC, 50/60 Hz for 1 min between non-continuous contacts

3 kV (between power terminals) for 100 to 240 VAC, 1 kV for 24 VAC/12 to 24 VDC and 12 to 24 VDC

4.5 kV (between current-carrying terminal and exposed non-current-carrying metal parts) for 100 to 240 VAC,

1.5 kV for 24 VAC/12 to 24 VDC and 12 to 24 VDC

1.5 kV (between power terminals) for 100 to 240 VAC and 24 VAC/12 to 24 VDC, ±480 V for 12 to 24 VDC

600 V (between input terminals)

Square-wave noise by noise simulator (pulse width: 100 ns/1 µs, 1-ns rise)

Destruction: 15 kV Malfunction: 8 kV

Destruction: 10 to 55 Hz with 0.75-mm single amplitude, four cycles each in three directions (8 minutes per cycle) Malfunction: 10 to 55 Hz with 0.35-mm single amplitude, four cycles each in three directions (8 minutes per cycle)

Destruction: 294 m/s Malfunction: 98 m/s

Mechanical: 10,000,000 operations min. Electrical: 100,000 operations min. (3 A at 250 VAC, resistive load)

See

UL508/Listing, CSA C22.2 No. 14, conforms to EN61010-1 (Pollution degree 2/overvoltage category II) Conforms to VDE0106/P100 (finger protection).

(EMI) EN61326 Emission Enclosure: EN55011 Group 1 class A Emission AC mains: EN55011 Group 1 class A

(EMS) EN61326 Immunity ESD: EN61000-4-2: 4 kV contact discharge (level 2)

Immunity RF-interference: EN61000-4-3: 10 V/m (Amplitude-modulated, 80 MHz to 1 GHz) (level 3);

Immunity Conducted Disturbance: EN61000-4-6: 10 V (0.15 to 80 MHz) (level 3) Immunity Burst: EN61000-4-4: 2 kV power-line (level 3);

Immunity Surge: EN61000-4-5: 1 kV line to lines (power and output lines) (level 2);

Immunity Voltage Dip/Interruption EN61000-4-11: 0.5 cycle, 100% (rated voltage)

Panel surface: IP66 and NEMA Type 4 (indoors) (See note 2.)

Approx. 140 g

each in three directions

Life-test Curve

on page 92.

8 kV air discharge (level 3)

10 V/m (Pulse-modulated, 900 MHz ±5 MHz) (level 3)

1 kV I/O signal-line (level 4)

2 kV line to ground (power and output lines) (level 3)

Counters

Multifunction Preset Counter

H7CX

C-91

Life-test Curve (Reference Values)

■

Resistive Load Inductive Load

1,000

)

700

500

1,000

)

700

500

300

No. of operations (×10

250 VAC (cosφ=1)

100

01 2 3

30 VDC (cosφ=1)

Load current (A)

300

30 VDC (L/R=7 ms)

No. of operations (×10

100

250 VAC cosφ=0.4

01 2 3

Load current (A)

Reference: A current of 0.15 A max. can be switched at 125 VDC (cosφ=1) and current of 0.1 A max. can be switched if L/R=7 ms. In both cases, a life of 100,000 operations can be expected.

Inrush Current (Reference Values)

■

The minimum applicable load is 10 mA at 5 VDC (failure level: P).

Model Voltage Applied voltage Inrush current (peak value) Time

H7CX-A11/-AW 100 to 240 VAC 264 VAC 5.8 A 0.7 ms

H7CX-A11D1/-AWD1 24 VAC/12 to 24 VDC 26.4 VAC 10.4 A 1.2 ms

H7CX-AD 12 to 24 VDC 26.4 VDC 6.0 A 1.2 ms

C-92

Multifunction Preset Counter

H7CX

Connections

Block Diagram

■

(Basic

Output circuit

(Basic insulation)

Input circuit

All models except for H7CX-@D (models with 12 to 24-VDC power supplies) have basic insulation.

Note:

I/O Functions

■

Using as a Counter

insulation) Power supply

Internal control circuit

circuit

(See note.)

Display circuit

Key switch circuit

Counters

Inputs CP1, CP2 •

Reset or Reset 1 •

Total Reset or Reset 2 (See note 2.)

Outputs OUT1, OUT2

Note: 1.

In increment mode or increment/decrement mode, the present value returns to 0; in decrement mode, the present value returns to the set value with 1-stage models, and returns to set value 2 with 2-stage models.

The reset indicator will not be lit when the total reset or reset 2 input is ON.

In general (except for dual counter mode) Reads counting signals Increment, decrement, command, individual, and quadrature inputs accepted.

When used as a dual counter

•

Reads CP1 count signals with CP1 input and CP2 count signals with CP2 input. Increment signals can be input.

In general (except for dual counter mode) Resets present value and outputs (OUT2 when using the batch counter). (See note 1.) Counting cannot be performed during reset/reset 1 input. The reset indicator is lit during reset input.

When used as a dual counter

•

Resets the CP1 present value (to 0). Counting for CP1 input cannot be performed during reset 1 input. The reset indicator is lit during reset 1 input.

When used as a 1-stage/2-stage counter

•

Does not operate (Not used). When used as a total and preset counter

•

Resets the total count value. Holds the total count value at 0 during total reset input.

When used as a batch counter

•

Resets the batch count value and batch output (OUT1). Holds the batch count value at 0 during reset 2 input.

When used as a dual counter

•

Resets the CP2 present value. Counting for CP2 input cannot be performed during reset 2 input.

Outputs take place according to designated output mode when corresponding preset is reached.

Using as a Tachometer

Inputs CP1, CP2

Reset 1, Reset 2

Outputs OUT1, OUT2

Reads counting signals. (CP2 input is not used.)

Holds the measurement value and outputs. (Reset 2 input is not used.) The reset indicator is lit during hold.

Outputs signals according to the specified output mode when a set value is reached.

Multifunction Preset Counter

H7CX

C-93

Terminal Arrangement

■

Confirm that the power supply meets specifications before use.

H7CX-A/-A4 1-stage Contact Output

CP2

Reset

0 V

(−)

Sensor, etc.

(+)

External power supply

678910

12 VDC

11 12 13

1234

Unused Unused

OUT

H7CX-AS/-A4S 1-stage Transistor Output

CP2

Reset

0 V

(−)

Sensor, etc.

(+)

External power supply

678910

12 VDC

11 12 13

Unused Unused

CP1

Total reset

H7CX-AD/-A4D 1-stage Contact Output

0 V

678910

Unused Unused Unused

11 12 13

1234

(+)(−)

Total reset

OUT

CP2

CP1

Reset

Note: Terminals 1 and 6 are connected internally.

H7CX-ASD/-A4SD 1-stage Transistor Output

CP2

CP1

Reset

0 V

678910

Unused Unused Unused

11 12 13

Total reset

12345

OUT

H7CX-A11/-A114/-A11D1/-A114D1 1-stage Contact Output

Reset

CP1

CP2

0 V

(−)

Total reset

(−)

Sensor, etc.

Note:

12 VDC

(+)

External power supply

Do not connect unused terminals as relay terminals.

(+)

Internal circuit

OUT

12345

OUT

(+)

(−)

Note: Terminals 1 and 6 are connected internally.

H7CX-A11S/-A114S/-A11SD1 1-stage Transistor Output

Reset

CP1

CP2

Total reset

(−)

Sensor, etc.

12 VDC

(+)

External power supply

0 V

(−)

(+)

Internal circuit

OUT

C-94

Multifunction Preset Counter

H7CX

H7CX-AW/-A4W/-AWD1 2-stage Contact Output

Reset 1

0 V

(−)

Sensor, etc.

(+)

External power supply

678910

12 VDC

11 12 13

12345

(−)

(+)

CP2

OUT2

CP1

Reset 2

OUT1

H7CX-AWS/-AWSD1 2-stage Transistor Output

CP2

Reset 1

0 V

(−)

Sensor, etc.

(+)

External power supply

678910

12 VDC

11 12 13

12345

OUT2

(+)(−)

CP1

Reset 2

OUT1

Counters

H7CX-AWSD/-A4WSD 2-stage Transistor Output

CP2

CP1

Reset 1

0 V

678910

Unused

11 12 13

12345

(+)(−)

Reset 2

OUT1

OUT2

Note: 1. Terminals 1 and 6 are connected internally.

2. Do not connect unused terminals as relay terminals.

H7CX-AU/-AUD1 1-stage Contact, 1-stage Transistor Output

CP2

CP1

(−)

Sensor, etc.

(+)

12 VDC

External power supply

Reset 1

0 V

678910

11 12 13

Reset 2

OUT1 or 2

H7CX-AUSD1 1 or 2-stage Transistor Output

CP2

CP1

Reset 1

0 V

(−)

Sensor, etc.

(+)

External power supply

678910

12 VDC

11 12 13

12345

OUT 1 or 2

(+)(−)

Note: Each output can be flexibly allocated to

either stage 1 or 2 in function selection mode.

Reset 2

OUT1 or 2

12345

OUT 1 or 2

(+)(−)

Note: Each output can be flexibly allocated to either

stage 1 or 2 by setting in function selection mode.

Multifunction Preset Counter

H7CX

C-95

Input Circuits

■

CP1, CP2, Reset/Reset 1, and Total Reset/Reset 2 Input

+14 V

1 kΩ

The circuit shown above is for no-voltage input (NPN input).

Note:

Input Connections

■

Internal circuit

The inputs of the H7CX are no-voltage (short-circuit or open) inputs or voltage inputs.

No-voltage Inputs (NPN Inputs)

Open Collector

PLC or sensor

0 V

Input

Reset/reset 1 input

CP2 input

H7CX-A@ H7CX-A11@

Operates when the transistor turns ON.

6 7 8 9

3 7 5 6 4

CP1 input

Total reset/reset 2 input

Voltage Output

Sensor

0 V

Input

H7CX-A@ H7CX-A11@

Operates when the transistor turns ON.

6 7 8 9

3 7 5 6104

No-voltage Input Signal Levels

No-contact input Short-circuit level

Transistor ON Residual voltage: 3 V max. Impedance when ON: 1 KΩ max. (The leakage current is 5 to 20 mA when the impedance is 0 Ω.)

Open level Transistor OFF

Impedance when OFF: 100 KΩ min.

Contact input Use contact which can adequately switch

5 mA at 10 V. Maximum applicable voltage: 30 VDC max.

Reset/reset 1 input

CP2 input

CP1 input

Total reset/reset 2 input

Contact Input

0 V

Input

Reset/reset 1 input

CP2 input

H7CX-A@ H7CX-A11@

Operates when the contact turns ON.

6 7 8 9

3 7 5 6104

CP1 input

Total reset/reset 2 in

DC Two-wire Sensor

0 V

Input

Reset/reset 1 input

CP2 input

CP1 input

H7CX-A@ H7CX-A11@

Operates when the transistor turns ON.

Applicable Two-wire Sensor

Leakage current:1.5 mA max. Switching capacity:5 mA min. Residual voltage:3 VDC max. Operating voltage:10 VDC

C-96

6 7 8 9

3 7 5 6104

Multifunction Preset Counter

Total reset/reset 2 in

H7CX

Voltage Inputs (PNP Inputs)

No-contact Input (NPN Transistor)

Sensor

0 V

Input

Reset/reset 1 input

H7CX-A@ H7CX-A11@

Operates when the transistor turns OFF.

6 7 8 9

3 7 5 6104

CP2 input

CP1 input

Total reset/reset 2 input

No-contact Input (PNP Transistor)

H7CX-A@ H7CX-A11@

Operates when the transistor turns ON.

Voltage Input Signal Levels

High level (Input ON): 4.5 to 30 VDC Low level (Input OFF): 0 to 2 VDC Maximum applicable voltage: 30 VDC max. Input resistance: Approx. 4.7 k

Ω

Sensor

0 V

Input

Reset/reset 1 input

CP2 input

6 7 8 9

3 7 5 6104

Contact Input

CP1 input

Total reset/reset 2 input

H7CX-A@ H7CX-A11@

Operates when the contact turns ON.

0 V

Input

Reset/reset 1 input

6 7 8 9

3 7 5 6104

CP2 input

CP1 input

Total reset/reset 2 input

Counters

Multifunction Preset Counter

H7CX

C-97

Nomenclature

Indicators Operation Keys

Reset Indicator (Orange) Lit when the reset input (1) or reset key is ON.

Key Protection Indicator (Orange)

Control Output Indicator (Orange) OUT: One stage OUT1, OUT2: Two stages

Total Count Indicator Lit when the total count value is displayed.

Batch Indicator Lit when the batch count value is displayed.

Set Value 1, 2 Stage Indicator

Present Value (Main Display) Character height: 11.5 mm (6-digit: 9mm)

Set Value (Sub-display) Character height: 6 mm

4 5 6 9

Front view of 4-di

4 5 6

Front view of 6-digit mode

13 14

it mode

Mode Key Used to switch mode and setting items.

Reset Key The operation of the reset function depends on the configuration selected as shown in the table below.

Up Keys: 1 to 4 (6-digit models: 1 to 6)

Down Keys: 1 to 4

Switches

Key Protect Switch

(Factory setting) OFF ON

DIP Switch

Reset Operation by Reset Key

Configuration Reset operation

1-stage/2-stage

Resets the present value and outputs.

counter

Total and preset counter

Resets the present value and outputs.

•

When the total count value is displayed, resets

•

the present value, the total count value, and outputs.

Batch counter •

Resets the present value and OUT2. When the batch count value is displayed,

•

resets the present value, the batch count value, and outputs.

Dual counter

Resets the CP1 present value, CP2 present value, dual count value, and outputs.

Tachometer

Maintains the measured value and outputs (hold function).

C-98

Multifunction Preset Counter

H7CX

Dimensions

)

44.8

All units are in millimeters unless otherwise indicated.

Note:

Counter (without Flush Mounting Adapter)

■

Screw-terminal Models with External Power Supplies

• H7CX-A

• H7CX-AS

• H7CX-A4

• H7CX-A4S

• H7CX-AW

• H7CX-AWS

• H7CX-A4W

• H7CX-AWD1

X-AWSD

• H7

• H7CX-AU

• H7CX-AUD1

• H7CX-AUSD1

484

(Flush Mounting)

Note: M3.5 terminal screw (effective length: 6 mm

Screw-terminal Models without External Power Supplies

• H7CX-AD

• H7CX-ASD

• H7CX-A4D

• H7CX-A4SD

• H7CX-AWSD

48×48

44.8×44.8

Counters

44.844.

(Flush Mounting)

11-pin Socket Models

• H7CX-A11

• H7CX-A11S

• H7CX-A11D1

• H7CX-A11SD1

• H7CX-A114

• H7CX-A114S

X-A114D

• H7

Note: M3.5 terminal screw (effective length: 6 mm

(Flush Mounting/Surface Mounting)

484

72.

Multifunction Preset Counter

H7CX

C-99

+ 30 hidden pages