Omnitracs DecketPORT 468Q-2, MCP50 Installation Instructions Manual

To scan and send a document

1. From the Scanning home page, insert the

paper—face down.

• It will go in about ½ an inch.

• If it’s not 8½ inches wide,

align it with the right edge.
The small tooth in the slot
must be covered.

2. Choose the Document Type from the pull-down menu.

3. Check the Preview box if you would like to preview the scanned page before send-

ing (you will be able to accept or reject the page.)

Tap Scan Page.

4. After the page goes through, tap Done.

You can send up to 10 pages at a time. Simply insert another and tap Add Page be­fore you tap Send.

5. Tap Send and then tap OK to confirm your choice.

 For initial support, call Omnitracs Customer Support at [phone].

 If you want to follow up on an RMA for status and have already

received an RMA number from Quest Solution, contact:

Quest Solution

[phone] Phone

http://omnitracs.questsolution.com/q/mobileprinters/default.aspx

RMA Authorization Process

Omnitracs, LLC
717 N. Harwood Street, Suite 1300
Dallas, TX 75201 U.S.A.

© 2016 Omnitracs, LLC. All rights reserved.
Omnitracs is a trademark of Omnitracs, LLC. All other trademarks are the property of their respective owners.
Omnitracs endeavors to ensure that the information in this document is correct and fairly stated,
but Omnitracs is not liable for any errors or omissions. Published information may not be up to date, and it is
important to confirm current status with Omnitracs.
This technical data may be subject to U.S. and international export, re-export or transfer (export) laws.
Diversion contrary to U.S. and international law is strictly prohibited.

80-JB533-1 Rev. A
October 2016

MCP50

In-Cab Scanning Installation Instructions, 468Q-2

Driver – Do not use while vehicle is in motion.

Use while driving will cause distraction and loss of vehicle control
which may lead to serious injury or death.

WARNING

 Getting Started
 Installation Checklist
 Step-by-Step Instructions
 Calibration
 Scanning and Sending
 RMAs

Getting Started

The following parts list consists of the items included in the
65-JB526-P3 or 65-JB526-P4 In-Cab Scanner kits. Use these numbers to order additional
parts.

 Scanner — PN 825-53392-2468

 Scanner Cable — PN 364-18579-3000

 Holster Kit — PN 825-53392-0002

(included in 65-JB526-P3 kit only)

 Mounting Kit — PN 65-J9632-2

(included in 65-JB526-P4 kit only)

 Cleaning & Calibration Sheets — PN 825-53392-0001

Use the following checklist when installing the scanner:

 Move the unit into the iQ Operational Profile with scanning and

customer-preferred applications (one time only).

 Install scanning hardware in the desired location, using the Dual Lock tape or holster

option.

 Calibrate the scanner.

 Scan and send a document. (See back page or on-board tutorial.)

 Check the Scanning Outbox to make sure it was sent successfully.

 Provide training for drivers and tell them to call them to call their Driver Manager or

Omnitracs Customer Support for help.

If you experience problems:

Call Omnitracs Customer Support at [phone].

Mounting the scanner near the
vehicle airbags can injure a driver or passen­ger involved in a crash.

Airbag firing can cause the scanner to be­come a projectile leading to serious injury or
death.

Mount the scanner in a location that will not
be impacted by the firing of any forward or
side airbag.

WARNING

Improper cable installation can
interfere with the vehicle pedals or
steering.

Interfering with the pedals or steering can
cause a crash, resulting in serious injury or
death.

Mount the cables so that they cannot inter­fere with the brake, accelerator, clutch, or
steering wheel, EVEN IF THE TIE WRAPS

WARNING

Installation Checklist

MAY CONTAIN U.S. AND INTERNATIONAL EXPORT CONTROLLED INFORMATION

MAY CONTAIN U.S. AND INTERNATIONAL EXPORT CONTROLLED INFORMATION

Installation Steps

Connect the scanner

1. Remove the metal cover from the MAS USB/SER connector.

2. Select the scanner location.

3. Insert the B Connector of the USB cable into the scanner and the A Connector
into either USB port on the MAS.

4. If mounting the scanner only, see step 2a.
If mounting a holster to stow scanner, see step 2b.

5. driver, or
hinder truck performance.

Note: It may be necessary to route the cable under wells and interior molding.

Mount the scanner directly—no holster (65-JB526-P4)

1. Confirm the scanner location.

2. Clean the scanner bottom and the mounting surface with an alcohol pad and let
dry.

3. Remove the backing from two pieces of Dual Lock Tape and apply them to the
bottom ends of the scanner.

4. Remove the backing from the other two pieces of Dual Lock Tape and apply
them to the mounting surface.

5. Position the scanner in the desired location and press firmly

to secure the grip of the Dual Lock Tape.

Mount a holster to stow the scanner (65-JB526-P3)

1. Select the holster location.

2. Clean the mounting surface with an alcohol pad and let dry.

3. Remove the backing from the Dual Lock Tape on the holster.

4. Position the holster in the desired location and press firmly
to ensure contact with the surface.

Calibrate the scanner

1. From the Display Interface Unit home screen, tap Scanning.

2. From the Scanning home screen, tap Options.

3. Insert the black and white calibration page (or a plain white sheet of paper) into
the scanner until it engages.

4. Tap Calibrate. When the paper finishes moving through the scanner, tap Scan to
return to the Scanning home screen.

Note: Calibrate and clean the scanner once per month. Refer to MCP training.