Omega Products XRU1H120U User Manual

K-5
HIGH CURRENT TERMINAL BLOCK RELAYS
XRU1H Series
Starts at
$
23
Field Replacement
l Convenient Plug-In Bridge System l LED Status Indication l DIN Rail Mount l IP67 Protected
Optical Electronics
l Wear-Resistant and
Bounce-Free Switching
l Insensitive to Shock and Vibration l Integrated Protection Circuit l Zero Voltage Switch at AC Output l Environmentally Friendly,
Cadmium Free Contact Material
l Electrical Isolation Between
Input and Output
The new XR Series relays include products designed to meet high continuous current and/or long electrical service life applications. The XR Series relays are plug­in interfaces that connect to basic terminal blocks that use screw connection technology. Overall width is 14 mm (0.55").
These relays are best suited for applications that require higher continuous load currents than miniature relays can carry and switch. They can withstand inrush currents or brief overloads without damage, and allow for continuous load currents of up to 10 A. The XR Series Relay boasts an average service life of the contacts that is two or three times the normal life of a less powerful relay, resulting in service cost savings.
Accessories
Power Terminal Block
The XRAPLCESK power terminal block has the same shape as the relay modules and is used to feed in the bridging potentials. The nominal current is 32 A. When the total current is less than or equal to 6 A,
supply can take place directly at the connecting terminal blocks of one of the connected relays.
End Cover
The XRAATPBK end cover is required at the start and stop of a relay strip. It can also be used for visual separation of groups of relays as well as separating relays with voltages greater than 250V and separating neighboring bridges with different potentials. It is equipped with pre-scored break out points at the bridging positions so that individual bridges can be passed through as needed. It may also be necessary to use the end cover between adjacent relays when three phases (L1, L2, L3) are used on the contact side of the relay.
Bridges
The XRAFBST colored, insulated plugin bridge system reduces wiring time by up to 70% compared to conventionally wired relays. The XRAFBST2, 2-position bridges, are suited for bridging a smaller number of relays and total currents < 6A. When a circuit is supplied from both sides, the circuit can be opened at any point, allowing all other modules to continue being supplied at the same time. The XRAFBST500 allow up to 80 modules to be bridged at one time. If bridges with different potentials meet in neighboring modules, the end cover XRAATPBK should be used. All bridges are equipped with a groove for removal with a standard screwdriver.
XRU1H120U, $27, shown slightly larger than actual size.
K-6
11
14
12
A2
A1
MODEL NO. PRICE DESCRIPTION
XRU1H120U $27 1 PDT high current relay with 120 Vac/110 Vdc coil voltage XRU1H24U 23 1 PDT high current relay with 24 Vac/Vdc coil voltage
To Order
(Specify Model Number)
AVAILABLE FOR FAST DELIVERY!
Ordering Example: XRU1H120U, relay, $27.
REPLACEMENT RELAYS AND ACCESSORIES
MODEL NO. PRICE DESCRIPTION
XRR1H120U $12.00 Replacement relay for XRU1H120U XRR1H24U 10.00 Replacement relay for XRU1H24U XRAPLCESK-5PK 125.00 Power terminal block, 5 pack XRAATPBK-5PK 10.50 Black end cover, 5 pack XRAFBST2RD-10PK 14.00 2-position red snap in jumper, 10 pack XRAFBST2BU-10PK 14.00 2-position blue snap in jumper, 10 pack XRAFBST2GY-10PK 14.00 2-position gray snap in jumper, 10 pack XRAFBST500RD-5PK 110.00 80-position red snap in jumper, 5 pack XRAFBST500BU-5PK 110.00 80-position blue snap in jumper, 5 pack XRAFBST500GY-5PK 110.00 80-position gray snap in jumper, 5 pack
94 (3.70)
14 (0.55)
80 (3.15)
Dimensions:
mm (in)
SPECIFICATIONS
Connection Data:
Rigid Solid AWG (mm2):
26 to 14 (0.14 to 2.5)
Flexible Stranded AWG (mm2):
26 to 14 (0.14 to 2.5)
Input Voltage:
XRU1H24U: 24 Vac/Vdc XRU1H120U: 120 Vac/110 Vdc
Typical Input Current:
XRU1H24U: 17.5 mA XRU1H120U: 4.5 mA (120 Vac)/
4.2 mA (110 Vdc)
Typical Response Time:
XRU1H24U: 8 mS XRU1H120U: 7 mS
Typical Release Time: 10 mS
Input Protection: Bridge rectifier OUTPUT DATA
Contact Type: Single contact, 1 PDT Contact Material: AgNi Max Switching Voltage: 250 Vac/Vdc
1
Min Switching Voltage: 12 Vac/Vdc Limiting Continuous Current:
10 A (6 A)
2
Max Inrush Current: 30 A (300 mS) Min Switching Current: 100 mA Min Switching Power: 1.2 W
MISCELLANEOUS DATA Test Voltage I/O: 4 kV, 50 Hz, 1 min Ambient Temp Range: -20 to 60°C
(-4 to 140°F)
Rated Operating Mode:
100% Operating Factor Inflammability Class: V0, in
Accordance with UL 94
Mechanical Service Life:
3 x 107 cycles
1 The separating plate, XRAPLCESK, should be installed for voltages greater than 250V (L1, L2, L3) between identical terminal points of adjacent modules. Potential bridging is then possible with the XRAFBST bridge system. 2 The current rating for the normally open contact (#14) is 10 A. The current rating for the normally closed contact (#12) is 6 A and can be increased to 10 A by bridging the two #12 contact connections.
Schematic for high current terminal block relays
Loading...
+ 1 hidden pages