Omega Products WMS-22A Installation Manual

WMS-22A
and
WMS-22
@
fl
Current Loop Wind Stations
WMS-22A Wind Speed indicator
*
WMS-22 Wind Speed and Direction Indicator
Operator s
Manual
Unpacking Instructions
Remove the Packing List and verify that you have received all equipment, including the following
(quantities in parentheses):
0
WMS-22A or WMS-22. Wind Sensor
0
Transmitter Housing Assembly, with I/O connection terminal strips
-
_-_
l
Operators Manual
If you have any questions about the shipment, please call the OMEGA Customer Service Department. When you receive the shipment, inspect the container and equipment for signs of damage. Note any
evidence of rough handling in transit. Immediately report any damage to the shipping agent.
The carrier will not honor damage claims unless all shipping material is saved for inspection. After examining and removing contents, save packing material and carton in the event reshipment is necessary.
Servicing USA and Canada: Call OMEGA
Toll
Free
USA
One Omega Stamford, CT 06907-0047 Telephone: (203) 359-1660 FAX: (203) 359-7700
Sales Service: l-800-826-6342
Customer Service: l-800-622-2378
Engineering Service: l-800-872-9436
TELEX: 996404 EASYLINK: 62968934 CABLE: OMEGA
Drive, Box 4047
Canada
976 Bergar
Lava1
(Quebec) Telephone: (514) 856-6928 FAX: (514) 856-6886
l-SOO-TC-OMEGASM
/
l-SOO-622-BESTSM
/
l-SOO-USA-WHENSM
/
H7L
5Al
Servicing Europe: United Kingdom Sales and Distribution Center
25 Swannington Road, Broughton Astley, Leicestershire
6TU,
England
FAX: 44 (1455) 283912
LE9
Telephone: 44 (1455) 285520
The OMEGA Complete Measurement and
Control Handbooks
V
Temperature
&
V
Pressure, Strain
r/
Flow and Level
DH
I/
and
Conductivitv
Force
&
Encyclopedias
V
Data
V
Electric Heaters
V
Environmental Monitoring
Acquistion Systems
and Control
Call for Your FREE Handbook Request
MHDOS95HABA
Form Today:
(203)
359-RUSH
OMEGA Engineering
Model WMS-22 and WMS-22A Current Loop
WindStations
Instruction Manual
1.0 INTRODUCTION
The WMS-22 Current Loop paramenter into 4-20 external power is required since the encoding electronics for wind speed and for wind direction are
isolated and powered from their respective 2-wire current loops.
The WMS-22 wind sensor includes a three-cup anemometer and wind vane. The sensor is ruggedly constructed of UV-resistant ABS plastic and anodized aluminum parts. The cable that connects the pole-mounted wind sensor to the encoder electronics package may be extended up to a total of 250 feet. The encoded current loops signals may be transmitted over distances of up to several miles. The electronics package, which is typically mounted in an indoor locations, is supplied in a gasketed, wall-mounted
The measurement time base for the wind speed-to-current conversion in the encoder is crystal controlled for stable long-term accuracy. direction measurement circuitry to minimize drift and non-linerity.
NEMA-4X
mA
WindStation
output signals for use by process control or monitoring systems.
enclosure.
measures wind speed and direction and converts each
No
Likewise, ratiometric signal conditioning is used to the
Two versions are offered; the WMS-22A measures wind speed only, while the WMS-22 measures
both wind speed and direction. The WMS-22 systems consist of two subassemblies: a wind sensor
and a signal conditioning electronics assembly.
2.0 PHYSICAL DESCRIPTION
2.1 The Wind Sensor
The rotating assembly containing the three-cup anemometer and wind vane for sensing wind speed and directional information is called the wind sensor. The wind vane is mounted on a common axis with the anemometer and includes a tail fin with a nose weight that provides balance. is coupled to an angular encoder which is housed within the cylindrical weather skirt.
2.2 The Encoder
The encoder electronics package is housed in a sealed NEMA enclosure and contains two independent 4-20
mA
data channels, one for wind speed and the second for wind direction.
its respective 2-wire measurement loop.
Each- is powered from
The wind vane
Loading...
+ 8 hidden pages