Page 1
High Power Wireless Transmitters
Ethernet or Internet Connection
zED-TP1-LCD
shown smaller
than actual size.
Display Models
zED Series
zED-TP1-P
shown smaller
than actual size.
†
Optional
U Web Server
U Alarms by Email or Text Message
U No Special Software Required
U High Power
U NEMA 4 (IP65) Enclosure
The rugged high-performance, high power OMEGA®
wiSeries wireless transmitters are compatible with
the OMEGA zSeries and wiSeries system for Webbased monitoring of Analog Voltage and Current,
Temperature, Humidity, and Barometric Pressure.
The radio is a high power IEEE 802.15.4 compliant
transmitter operating at 2.4 GHz designed to
transmit over greater distances and through more
obstructions than the standard transmitter.
These wireless sensors transmit 1000 m (3280’)—
without obstructions or interferences—to a zSeries
coordinator or wiSeries meter-controller. The
coordinators and controllers connect directly to an
Ethernet network and the Internet and serve active
Web Pages to display and chart the data.
You can monitor and record analog voltage
and current, temperature, relative humidity, and
barometric pressure over an Ethernet network or
the Internet without any special software—just your
Web Browser.
These wiSeries wireless sensors are designed
for demanding industrial applications indoors and
harsh outdoor environments. The electronics are
protected in a rugged weatherproof polycarbonate
NEMA 4 (IP65) rated housing. The rugged
industrial sensors are supplied with 3 m (10’)
of cable.
†
Refer to page W-54 for NIST calibration ordering information.
Lug mount
probe
included with
zED-TP2-P.
Meter-Controller/Coordinator
wi833-ZT meter controller/
coordinator shown
smaller than actual size.
For more information, visit
omega.com
Models Available for:
• Temperature
• Barometric Pressure
• Humidity
• Dual Thermocouple
• Analog Voltage
EXTERNAL PROBES
Temperature/humidity
or barometric pressure/
temperature probe
included with
zED-THP-P.
Stick probe
included with
zED-TP1-P.
zCDR shown smaller
than actual size. For
more information, visit
omega.com
W-51
Page 2
Wireless Transmitters
Wireless transmitters are available with external probes
appropriate for an almost unlimited variety of industrial
and commercial applications.
OMEGA offers a selection of end devices for a
variety of applications. The high power end device
supports one external sensor. The external sensors
are designed for harsh environments such as outdoor
weather, in HVAC ducts, in freezers and refrigerators.
OMEGA offers wireless sensor/transmitters that run on
either batteries or AC power. The battery version
(zED-CCELL) comes with two alkaline C-Cell batteries
that can last for years. The AC version (zED-P,
zED-LCD) comes with a 5 Vdc universal AC adaptor that
operates on any voltage worldwide (110 to 240 Vac).
Should AC power fail, the unit can operate on a 3.6V
ultra-long-life lithium backup battery (included). It
can run on battery power for days, weeks, or months
depending on the read rate selected by the user.
Alarm and Email
The wiSeries wireless sensor system can trigger
an alarm if variables go above or below a set point
that you determine. Your alarm can be sent by
email to a single user or to a group distribution list,
including text messages to cell phones and PDAs.
The OMEGA “MailNotifier” software is a free and
easy program for this application.The meter-controller
connects directly to an Ethernet Network or the
Internet. Unlike an RS232 or USB device, it does
not require a host computer.
Embedded Web Server
The wiSeries wireless sensor system is easy to install,
simple to operate, and features OMEGA’s awardwinning iServer technology with an Embedded Web
Server that requires no special software.
Charts and Graphs
The wiSeries system serves Active Web Pages to
display real time readings and charts of Analog Voltage
and Current, Temperature, Humidity, and Barometric
Pressure. You can also log data in standard data
formats for use in a spreadsheet or data acquisition
program such as Excel or Visual Basic.
OMEGA offers a free and easy to use program for
logging data to Excel. The virtual chart viewed on the
web page is a JAVA™ Applet that records a chart
over the LAN or Internet in real time. With the OMEGA
wiSeries system there is no need to invest time and
money learning a proprietary software program to log
or chart the data. Chart scales are fully adjustable on
the fly. For example, the chart can display one minute,
one hour, one day, one week, one month or one year.
Temperature and humidity can be charted across the
full span [-40 to 125°C (-40 to 257°F), and 0 to 100% RH]
or within any narrow range such as [20 to 30°C
(68 to 86°F)]. OMEGA offers an OPC Server software
that makes it easy to integrate the wiSeries wireless
Internet
Enabled!
sensor system with many popular Data Acquisition and
Automation programs offered by OMEGA, Wonderware,
iConics, Intellution, Rockwell Automation, and National
Instruments, among others.
Specifications
Relative Humidity
Accuracy/Range (zED-THP-x, zED-BTHP-x): ±2% for
10 to 90%; ±3% for 5 to 10% and 90 to 95%; ±4% for 0 to 5%
and 95 to 100%
Hysteresis: ±1% RH
Non-Linearity: ±3%
Repeatability: ±0.1%
Resolution: 0.1%
Temperature
Accuracy/Range zED-TP1-x, zED-TP2-x:
±0.5°C for 10 to 85°C (±0.9°F for 50 to 185°F);
±1°C for -40 to 10°C and 85 to 125°C
(±1.8°F for -40 to 50°F and 185 to 257°F)
zED-THP-x, zED-BTHP-x:
±1°C for -18 to 0°C and 45 to 70°C
(±1.8°F for -0.4 to 32°F and 113 to 158°F); ±2°C for
-40 to -18°C and 70 to 124°C (±3.6°F for -40 to -0.4°F
and 158 to 255°F)
zED-THP-x, zED-THP2-x:
±0.5°C for 5 to 45°C (±0.9°F for 41 to 113°F);
up to ±1.5°C for -40 to 5°C and 45 to 124°C
(up to ±2.7°F for -40 to 41°F and 113 to 255°F)
zED-BTHP-x, zED-BTP-x:
±0.8°C @ 20°C (±1.5°F @ 68°F); ±2°C for
40 to 85°C (±3.6°F for -40 to 185°F)
Repeatability: ±0.1°C for zED-THP-x, zED-BTHP-x
Resolution: 0.1°C
Barometric Pressure
Accuracy/Range (zED-BTP-x, zED-BTHP-x): ±2 mbar for
10 mbar to 1100 mbar (1 KPa to 110 KPa)
Resolution: 0.1 mbar
Probe Specifications
Industrial Probe (zED-BTP-x, -BTHP-x, zED-THP-x):
SS 316 housing, 137 x Ø16 mm (5 x Ø0.63")
Stick Probe (zED-TP1-x): ABS tubing, 152.4 x Ø6.35 mm
(6 x Ø0.25")
Lug Mounted Probe (zED-TP2-x): Copper tubing,
53.4 x Ø7.92 mm (2.1 x Ø0.312"); mounting hole Ø4.72 mm
(Ø0.186")
Cable:
zED-TP1-x, -TP2-x, zED-THP-x: 3 m (10') L x Ø2.62 mm
(0.103"); -80 to 200°C (-112 to 392°F)
zED-BTP-x, -BTHP-x: 3 m (10') L x Ø4.45 mm (0.175");
-55 to 105°C (-67 to 221°F)
Thermocouple Input
Temperature Accuracy/Range: Refer to T/C chart, on next page
Temperature Stability: 0.08°C/°C
Temperature Coefficient: ±25 ppm/°C
Thermocouple Cold End Tracking: 0.1°C/°C
Thermocouple Lead Resistance: 100 Ω maximum
Thermocouple Type (ITS 90): J, K, T, E, R, S, B, C, N, L (DIN J)
Warm-Up to Rated Accuracy: 30 minutes
ø = diameter
W
W-52
Page 3
Analog Input
Voltage Input: Differential; bipolar; ±100 mV, ±1V, ±10V
Input Impedance: 400 kΩ for voltage
Current Input: Differential; bipolar; ±20 mA (5 Ω load)
Accuracy: ±1% full range @ 25°C
Reading Rate: Periodic (1 sample/update) or continuous
(20 samples/second)
A/D Conversion: Sigma-Delta
Resolution: 16-bits
Temperature Coefficient: ±50 ppm/°C
Common Mode Rejection: 105 dB
Normal Mode Rejection: 98 dB
Warm-Up to Rated Accuracy: 30 minutes
Wireless Communication
Standard: IEEE 802.15.4, DSSS
Frequency: 2.4 GHz (2400 to 2483.5 MHz), 16 channels
Network Topology: Star topology
Range: Up to 1000 m (3280’) without obstructions or
interference
Power (zED-x-P, zED-x-LCD)
Power Input: 5 Vdc
Consumption: 0.8 W max
Safety Qualified AC Power
Adaptor (Included):
Nominal Output: 5 Vdc @ 0.6 A
Input: 100 to 240 Vac, 50/60 Hz
Operating Temperature: 0 to 40°C (32 to 104°F)
Lithium Back-up Battery: One 3.6 Vdc (included)
Lifetime: Estimate of 2 years with frequency of
1 reading per 2 minutes (7 months with -TC/-VI option)
Power (zED-x-CCELL)
Alkaline Battery: Two C-cell 1.5 Vdc (included)
Lifetime: Estimate of 5 years with frequency of
1 reading per 2 minutes
Environmental
Operating Temperature:
zED-x-P: -20 to 70°C (-4 to 158°F),
90% RH non-condensing
zED-x-CCELL: -18 to 55°C
(-0.4 to 131°F), 90% RH
non-condensing
zED-x-LCD: -10 to 60°C (14 to 140°F),
90% RH non-condensing
Packaging
Enclosure Material: Polycarbonate
Enclosure Protection: NEMA 4 (IP65)
Enclosure Dimensions:
135.9 L x 82 W x 39 mm D
5.35 x 3.23 x 1.56”)
General
Agency Approval: FCC Part 15C; CE
EMC; 2004/108/EC, LVD 2006/95/EC,
RTT&E 1999/5/EC
Software: iConnect (configuration
software for the Ethernet interface), iLog
(Excel-based software for automatic data
logging), and Mail Notifier (email alarm
notification software)
Input Type Range Accuracy
-270 to -160°C/-160 to 1372°C 1.0°C/0.4°C
-270 to -190°C/-190 to 400°C 1.0°C/0.4°C
-270 to -220°C/-220 to 1000°C 1.0°C/0.4°C
Iron - Constantan
CHROMEGA
Copper - Constantan
CHROMEGA
-50 to 40°C/40 to 1768°C 1.0°C/0.5°C
-50 to 100°C/100 to 1768°C 1.0°C/0.5°C
100 to 640°C/640 to 1820°C 1.0°C/0.5°C
W/
Pt/30%Rh-Pt/6%Rh
5%Re-W/26%Re
-250 to -100°C/-100 to 1300°C 1.0°C/0.4°C
L
®
- ALOMEGA
®
- Constantan
Pt/13%Rh-Pt
Pt/10%Rh-Pt
Nicrosil - Nisil
-200 to 900°C (-328 to 1652°F) 0.4°C (0.7°F)
J DIN
W-53
Universal AC
adaptor is
included with all
AC powered
models.
107.7
(4.24)
82.0 (3.23)
5.99
(0.236)
135.8
(5.35)
123.77
(4.873)
CABLE
GLANDS
USED FOR
-TC AND -VI
QUICK
DISCONNECT
CONNECTORS
15.0
(0.59)
(COVER REMOVED)
(2.046)
TOP VIEW
51.97
ø3.56
(0.140)
4 PLCS
25 (1.0)
57.2 (2.25)
39.7 (1.56)
Dimensions: mm (inch)
ø = diameter
Thermocouple Chart
-210 to 760°C (-346 to 1400°F) 0.4°C (0.7°F)
®
(-454 to -256°F/-256 to 2502°F) (1.8°F/0.7°F)
(-454 to -310°F/-310 to 752°F) (1.8°F/0.7°F)
(-454 to -364°F/-364 to 1832°F) (1.8°F/0.7°F)
(-58 to 104°F/104 to 3214°F) (1.8°F/0.9°F)
(-58 to 212°F/212 to 3214°F) (1.8°F/0.9°F)
(212 to 1184°F/1184 to 3308°F) (1.8°F/0.9°F)
0 to 2320°C (32 to 4208°F) 0.4°C (0.7°F)
(-418 to -148°F/-148 to 2372°F) (1.8°F/0.7°F)
Page 4
High Power Wireless
Internet
Enabled!
Transmitters
A complete wireless system requires at least: 1 end device zED-x-P, zED-x-LCD, or zED-x-DCELL
(up to 8 end devices) and 1 coordinator or meter/controller (receiver) zCDR, wi8xx-ZT, or wiDRxx-ZT.
To Order Visit omega.com/zed-p_series for Pricing and Details
Model No. Description
Wireless End Device
zED-TP1-P Temperature sensor with stick probe, AC powered
zED-TP2-P Temperature sensor with lug mount probe, AC powered
zED-THP-P Temperature and humidity sensor, AC powered
zED-BTP-P Barometric pressure and temperature sensor, AC powered
zED-BTHP-P Barometric pressure, temperature and humidity sensor, AC powered
zED-TC-P Dual thermocouple input, AC powered
zED-VI-P Analog input, AC powered
zED-THP2-LCD-AA-H
zED-THP2-CCELL-H Short probe with temperature and humidity sensor, CCELL battery powered, horizontal case
zED-TP1-CCELL Temperature sensor with stick probe, battery powered
zED-TP2-CCELL Temperature sensor with lug mount probe, battery powered
zED-THP-CCELL Temperature and humidity sensor, battery powered
zED-BTP-CCELL Barometric pressure and temperature sensor, battery powered
zED-BTHP-CCELL Barometric pressure, temperature and humidity sensor, battery powered
zED-TC-CCELL Dual thermocouple input, battery powered
zED-VI-CCELL Analog input, battery powered
zED-TP1-LCD Temperature sensor with stick probe, AC powered, LCD display
zED-TP2-LCD Temperature sensor with lug mount probe, AC powered, LCD display
zED-THP-LCD Temperature and humidity sensor, AC powered, LCD display
zED-BTP-LCD Barometric pressure and temperature sensor, AC powered, LCD display
zED-BTHP-LCD Barometric pressure, temperature and humidity sensor, AC power, LCD display
zED-TC-LCD Dual thermocouple input, AC powered, LCD display
zED-VI-LCD Analog input, AC powered, LCD display
Wireless Coordinator and Meter Controller with Coordinator (Receivers)
zCDR Coordinator, which can support up to 32 end devices
zCDR-VI Coordinator, which can support up to 32 analog input end devices
wi833-ZT Meter/controller, which can support up to 8 temperature end devices, with 2 relays:
wi853-ZT Meter/controller, supports up to 8 temperature end devices, with analog output
wiDR22-ZT DIN rail monitor/controller, supports up to 8 temperature end devices, with 2 solid state
wiDR44-ZT-DC DIN rail monitor/controller, supports up to 8 temperature end devices, with 2 pulsed 10 Vdc @
Short probe with temperature and humidity sensor, AA battery powered, LCD display, horizontal case
Form “C” SPDT 3 A @ 120 Vac, 3 A @ 240 Vac, embedded Ethernet, 90 to 240 Vac, 50/60 Hz
0 to 10 Vdc or 0 to 20 mA @ 500 Ω max and Form “C” SPDT 3 A @ 120 Vac, 3 A @ 240 Vac,
embedded Ethernet, 90 to 240 Vac, 50/60 Hz
relays (SSRs): 0.5 A @ 120/240 Vac continuous, embedded Ethernet, 90 to 240 Vac, 50/60 Hz
20 mA (for use with external SSR), embedded Ethernet, low power option 12 to 36 Vdc, 24 Vac
W
Calibration† Description
CAL-3-HU NIST traceable calibration certificate; three humidity points: 25%, 50%, 75%, 1 temperature point of
CAL-3-HU-P-T NIST traceable calibration certificate; three humidity, barometric pressure, and temperature points
CAL-3-P NIST traceable calibration certificate; three barometric pressure points, and temperature 25°C
CT485B-CAL-KIT Calibration kit, 33% and 75% RH standards
For the meter/controllers, other output options are available, please contact our Sales Department.
Comes complete with software, 2 C-cell batteries, or AC power adaptor, and operator’s manual.
Ordering Examples: Two zED-TP2-P high power end devices with external temperature sensor in lug mounting probe housing and 3 m (10') cable,
and zCDR, coordinator.
CAL-3-HU, NIST traceable calibration certificate for new unit.
25°C (for new units)
(for new units)
(for new units)
W-54
Loading...