Omega Products FLSC790-P Installation Manual

Page 1
User’s Guide
®
®
omega.com
http://www.omega.com
e-mail: info@omega.com
®
FLSC790-P
Pulse Output Module
For use with FTB790 Series
Turbine Meters with Display Electronics
Page 2
omega.com
omega.com
OMEGAnet® On-Line Service Internet e-mail
http://www.omega.com info@omega.com
Servicing North America:
USA: One Omega Drive, Box 4047
ISO 9001 Certified Stamford, CT 06907-0047
Canada: 976 Bergar
Tel: (203) 359-1660 FAX: (203) 359-7700 e-mail: info@omega.com
Laval (Quebec) H7L 5A1 Tel: (514) 856-6928 FAX: (514) 856-6886 e-mail: info@omega.ca
®
®
®
For immediate technical or application assistance:
USA and Canada: Sales Service: 1-800-826-6342 / 1-800-TC-OMEGA
Customer Service: 1-800-622-2378 / 1-800-622-BEST Engineering Service: 1-800-872-9436 / 1-800-USA-WHEN TELEX: 996404 EASYLINK: 62968934 CABLE: OMEGA
SM
SM
SM
Mexico and Tel: (001) 800-826-6342 FAX: (001) 203-359-7807 Latin America: En Español: (001) 203-359-7803 e-mail: espanol@omega.com
Servicing Europe:
Benelux: Postbus 8034, 1180 LA Amstelveen, The Netherlands
Tel: (31) 20 6418405 FAX: (31) 20 6434643 Toll Free in Benelux: 0800 0993344 e-mail: nl@omega.com
Czech Republic: ul. Rude armady 1868, 733 01 Karvina-Hranice
Tel: 420 (69) 6311899 FAX: 420 (69) 6311114 Toll Free: 0800-1-66342 e-mail: czech@omega.com
France: 9, rue Denis Papin, 78190 Trappes
Tel: (33) 130-621-400 FAX: (33) 130-699-120 Toll Free in France: 0800-4-06342 e-mail: france@omega.com
Germany/Austria: Daimlerstrasse 26, D-75392 Deckenpfronn, Germany
Tel: 49 (07056) 3017 FAX: 49 (07056) 8540 Toll Free in Germany: 0130 11 21 66 e-mail: info@omega.de
United Kingdom: One Omega Drive, River Bend Technology Centre
ISO 9002 Certified Northbank, Irlam, Manchester
M44 5EX, United Kingdom Tel: 44 (0161) 777-6611 FAX: 44 (0161) 777-6622 Toll Free in United Kingdom: 0800-488-488 e-mail: info@omega.co.uk
It is the policy of OMEGA to comply with all worldwide safety and EMC/EMI regulations that apply. OMEGA is constantly pursuing certification of its products to the European New Approach Directives. OMEGA will add the CE mark to every appropriate device upon certification.
The information contained in this document is believed to be correct, but OMEGA Engineering, Inc. accepts no liability for any errors it contains, and reserves the right to alter specifications without notice.
WARNING: These products are not designed for use in, and should not be used for, patient-connected applications.
Page 3
TABLE OF CONTENTS
Introduction ................................................1
Installation and Wiring .............................. 1
Technical Specifications ............................ 2
Typical Wiring ............................................3
Warranty/Disclaimer .................................. 5
Return Requests/Inquiries .......................... 5
INTRODUCTION
Caution: This Pulse Output Module is not
FM Approved. Therefore, use of this module with an approved metering system, voids FM Approval.
This module is designed to be used only with FTB790 Series Turbine Meters. More spe­cifically, turbine housings with the follow­ing models: FTB791, FTB792, FTB793, FTB794, and FTB795.
Combine the Pulse Access Module with an FTB790 Series T urbine Electronics to create a low-cost flow sensor with both local read­out and pulse output which interfaces with various counters, controllers, and compatible process equipment.
The pulse output of this module provides an unscaled, amplified, digital signal capable of transmission up to 5,000 ft. (1,524m) with­out additional signal conditioning or ampli­fication devices.
The Pulse Output Module comes complete, ready to install, with a circuit assembly, coverplate assembly , and 10 ft. (3m) of cable.
INSTALLATION & WIRING
T o install this module, follow the instructions given below.
1. Remove the back coverplate from the turbine housing.
2. Remove the display electronics from the front of the turbine.
NOTE: If you are installing more than one
Pulse Access Module a t a time, take care to keep the proper electronics paired with the original turbine.
+–
J2
J6
+–
3. The Pulse Access Module connects to a 10-pin connector located on the back side of the computer electronics next to the negative battery connectors. The 10-pin connector is sealed with a clear plastic sealant that must be carefully pried out with a small sharp tool inserted gently at the edges.
4. Remove the backing from the double-sided tape on the module’s PC board.
5. Carefully align the top pin on the PC board with the J2 position on the 10-pin connector and gently press the PC board into position between the batteries. The bottom pin will align with the J6 position.
6. Guide the loose ends of the wires from the PC board through the housing’s cavity to the back side of the turbine.
7. Install the display electronics to the front side of the turbine and tighten the four screws snugly.
Terminal
Block
White
White
J2
Pulse Out
Black
J6
Common
10-pin Connector
8. Connect the loose ends of the wires to the terminal block on the inside of the back coverplate provided with this mod­ule. Connect white (pulse out) to white and black (common) to black.
Caution: Do not connect the red wire. This
module does not require connection of the red wire. Use of this wire will damage your equipment.
Signal
Customer Interfacing Equipment
Black
Common
Internal External
1
Page 4
9. Install the back coverplate. Make sure the O-ring is securely seated and no wires are pinched.
10. Connect to the user interface device ac­cording to manufacturer’s instructions.
11. Refer to the etched K-factor on the tur­bine. See Turbine Manual for location of K-factor.
NOTE: Please remember to supply a 820
ohm (minimum) Pull Up Resistor if the interface device does not have one. Ref­erence illustration above as necessary.
TECHNICAL SPECIFICATIONS
The Pulse Output Module with a standard FTB790
Series Turbine Meter with Display Electronics
which are sold seperately.
Dimensions (FLSC790-P)
Frequency Range: 0 to 750 Hz Housing Material: Nylon 6/6 Strain Relief: Hubble-PG7 Coverplate Thread: Female 1/2-20 UNF-2B Cable: Belden 9363 Std. Cable Length: 10 ft. (3m) Temperature: +14° to +140°F
(–10° to +60°C)
Open Collector Currect Sinking Output
Applied Voltag e: 0 to 60 Volts DC Connection: Two Wire Allowable Current: Up to 100 mA Output: Square Wave Pulse.
Amplitude same as supplied voltage.
NOTE: Display electronics, which work in
conjunction with this module, continue to be powered with batteries.
3.25 in. (8.26 cm)
1.63 in.
(4.14 cm)
0.8 in.
(2.0 cm)
0.25 in. (.64 cm)
1.0 in.
(2.54 cm)
2.0 in.
(5.1 cm)
2
Page 5
TYPICAL WIRING
Wiring to DPF700 Series Panel Meter
For connecting to the DPF700 meter, attach the white wire to Pin 2 on TB2, “SIG IN”. The black wire goes to Pin 3 on TB2, “SIG GND”. Set the S1 switches for 12.4 VDC OUT. No connection is made to “EXCITATION OUT”; the white wire is pulled up to the 12.4 VDC excitation inside of the DPF700.
Wiring to DPF70 Series Panel Meter
(DPF75, DPF76, DPF78)
For connecting to DPF70 Series panel meter, connect white wire to Pin 5 (A input), the black wire to Pin 8 (DC Ground), and connect a 820 ohm (minimum) pull up resistor between Pin 5 and Pin 7 (DC Excitation)
3
Page 6
NOTES
4
Page 7
MADE
IN
USA
WARRANTY / DISCLAIMER
OMEGA ENGINEERING, INC. warrants this unit to be free of defects in materials and workmanship for a period of 13 months from date of purchase. OMEGA W arranty adds an additional one (1) month grace per iod to the normal one (1) year product warranty to cover handling and shipping time . This ensures that OMEGA’s customers receive maximum coverage on each product.
If the unit malfunctions, it must be returned to the factory for evaluation. OMEGA’s Customer Service De­partment will issue an Authorized Return (AR) number immediately upon phone or written request. Upon examination by OMEGA, if the unit is found to be defective, it will be repaired or replaced at no charge. OMEGA’s WARRANTY does not apply to defects resulting from any action of the purchaser, including but not limited to mishandling, improper interfacing, operation outside of design limits, improper repair, or un­authorized modification. This WARRANTY is VOID if the unit shows evidence of having been tampered with or shows evidence of having been damaged as a result of excessive corrosion; or current, heat, moisture or vibration; improper specification; misapplication; misuse or other operating conditions outside of OMEGA’s control. Components which wear are not warranted, including but not limited to contact points, fuses, and triacs.
OMEGA is pleased to offer suggestions on the use of its various products. However, OMEGA neither assumes responsibility for any omissions or errors not assumes liability for any damages that result from the use of its products in accordance with information provided by OMEGA, either verbal or written. OMEGA warrants only that the parts manufactured by it will be as specified and free of defects. OMEGA MAKES NO OTHER WARRANTIES OR REPRESENTATIONS OF ANY KIND WHATSOEVER, EXPRESS OR IMPLIED, EXCEPT THAT OF TITLE, AND ALL IMPLIED WAR­RANTIES INCLUDING ANY WARRANTY OF MERCHANTABILITY AND FITNESS FOR A PAR­TICULAR PURPOSE ARE HEREBY DISCLAIMED. LIMITATION OF LIABILITY: The remedies of purchaser set forth herein are e xclusiv e, and the total liability of OMEGA with respect to this order, whether based on contract, warranty, negligence, indemnification, strict liability or otherwise, shall not exceed the purchase price of the component upon which liability is based. In no event shall OMEGA be liable for consequential, incidental or special damages.
CONDITIONS: Equipment sold by OMEGA is not intended to be used, nor shall it be used: (1) as a “Basic Component” under 10 CFR 21 (NRC), used in or with any nuclear installation or activity; or (2) in medical appli­cations or used on humans. Should any Product(s) be used in or with any nuclear installation or acti vity, medical application, used on humans, or misused in any way, OMEGA assumes no r esponsibility as set forth in our basic W ARRANTY/DISCLAIMER language, and, additionall y, purchaser will indemnify OMEGA and hold OMEGA harmless from any liability or damage whatsoever arising out of the use of the Product(s) in such a manner.
RETURN REQUESTS / INQUIRIES
Direct all warranty and repair requests/inquiries to the OMEGA Customer Service Department. BEFORE RETURNING ANY PRODUCT(S) TO OMEGA, PURCHASER MUST OBTAIN AN AUTHORIZED RE­TURN (AR) NUMBER FROM OMEGA’S CUSTOMER SERVICE DEP ARTMENT (IN ORDER TO AVOID PROCESSING DELAYS). The assigned AR number should then be marked on the outside of the return package and on any correspondence. The purchaser is responsible for shipping charges, freight, insurance and proper packaging to prevent breakage in transit.
FOR WARRANTY RETURNS, please have the following information available BEFORE contact­ing OMEGA:
1. Purchase Order number under which the prod­uct was PURCHASED,
2. Model and serial number of the product under warranty, and
3. Repair instructions and/or specific problems relative to the product.
OMEGA’s policy is to make running changes, not model changes, whenever an improvement is possible. This affords our customers the latest in technology and engineering.
OMEGA is a registered trademark of OMEGA ENGINEERING, INC. © Copyright 1998 OMEGA ENGINEERING, INC. All rights reserved. This document may not be copied, photocopied,
reproduced, translated, or reduced to any electronic medium or machine-readable form, in whole or in part, without the prior written consent of OMEGA ENGINEERING, INC.
FOR NON-WARRANTY RETURNS, consult OMEGA for current repair charges. Have the fol­lowing information available BEFORE contacting OMEGA:
1. Purchase Order number to cover the COST of the repair,
2. Model and serial number of the product, and
3. Repair instructions and/or specific problems relative to the product.
5
Page 8
Where Do I Find Everything I Need for
Process Measurement and Control?
OMEGA… Of Course!
TEMPERATURE
Thermocouple, RTD & Thermistor Probes, Connectors, Panels & Assemblies
Wire: Thermocouple, RTD & Thermistor
Calibrators & Ice Point References
Recorders, Controllers & Process Monitors
Infrared Pyrometers
PRESSURE, STRAIN AND FORCE
Transducers & Strain Gauges
Load Cells & Pressure Gauges
Displacement Transducers
Instrumentation & Accessories
FLOW/LEVEL
Rotameters, Gas Mass Flowmeters & Flow Computers
Air Velocity Indicators
Turbine/Paddlewheel Systems
Totalizers & Batch Controllers
pH/CONDUCTIVITY
pH Electrodes, Testers & Accessories
Benchtop/Laboratory Meters
Controllers, Calibrators, Simulators & Pumps
Industrial pH & Conductivity Equipment
DATA ACQUISITION
Data Acquisition & Engineering Software
Communications-Based Acquisition Systems
Plug-in Cards for Apple, IBM & Compatibles
Datalogging Systems
Recorders, Printers & Plotters
HEATERS
Heating Cable
Cartridge & Strip Heaters
Immersion & Band Heaters
Flexible Heaters
Laboratory Heaters
ENVIRONMENTAL MONITORING AND CONTROL
Metering & Control Instrumentation
Refractometers
Pumps & Tubing
Air, Soil & Water Monitors
Industrial Water & Waste water Treatment
pH, Conductivity & Dissolved Oxygen Instruments
M3215 1/99
Loading...