Omega Products DP6-485-CABLE Installation Manual

DP6-4485-CCABLE

485 Programming Cable

M4534-0607

LP0697X

SPECIFICATIONS

1. POWER REQUIREMENTS: Port powered *

* An external 12 VDC (unit draw @ 35 mAmax.) can be applied if RS-232
output handshake lines are not available.

Note: When using an external supply, the supply should be connected only to

specifically labeled terminal block power inputs. Connecting an external
supply to the handshake lines may damage the unit.

2. BAUD RATE: 19200 Baud max.

3. RS-232 SIDE:

Connector: DB-9 female

4. RS485 SIDE:

Connector: terminal block

* External 12 VDC supply optional.

5. CERTIFICA TIONS AND COMPLIANCE:

Immunity to EN 500082-1 Residential, Commercial and Light Industry

(IEC 801-2, IEC 801-3, IEC 801-4)

Emissions to EN 500081-1 Residential, Commercial and Light Industry

(EN 55022)

6. CONVERTER DIMENSIONS: L = 3.50" (88.9 mm) x W = 1.34" (34 mm)

x H = 0.67" (17 mm)

7. CABLE LENGTH: 7 feet (2.13 meters)

SIGNAL PIN

TD 2

GND

RD

5

3

RTS 7 to pin 8

CTS 8 to pin 7
DTR 4 to pin 6, 1
DSR 6 to pin 4, 1

CD 1 to pin 4, 6

JUMPERED

TERMINAL RJ11 CABLE

TD(A) Green
TD(B) Yellow

GND Red
GND *
+12V *

DESCRIPTION

The DP6-485-CABLE Programming Interface Cable is a port-powered device that can be used to
download or interface with products that have an RS485 RJ-11 port. The cable converts the RS-232
TD and RD lines to balanced half-duplex RS-485 signals which can transmit up to 4,000 feet at
19,200 baud. It is powered from the RS-232 data and handshake lines whether the lines are high
or low. An external 12 V power supply can be connected to two terminals on the connector
if handshake lines are not available.

The DP6-485-CABLE has a DB-9 female connector on the RS-232 side for
connection to a PC COM port. The RS485 side, has a terminal block where
the 7' long RJ11 cable is connected.

INSTRUCTION

SHEET

Shop online at: omega.com e-mail: [e-mail]
For latest product manuals: omegamanual.info

WARRANTY/DISCLAIMER

OMEGA ENGINEERING, INC. warrants this unit to be free of defects in materials and workmanship for a period of 25 months from date of purchase.
OMEGA’s WARRANTY adds an additional one (1) month grace period to the normal two (2) year product warranty to cover handling and shipping time.
This ensures that OMEGA’s customers receive maximum coverage on each product.

If the unit malfunctions, it must be returned to the factory for evaluation. OMEGA’s Customer Service Department will issue an Authorized Return (AR)
number immediately upon phone or written request. Upon examination by OMEGA, if the unit is found to be defective, it will be repaired or replaced at no
charge. OMEGA’s WARRANTY does not apply to defects resulting from any action of the purchaser, including but not limited to mishandling, improper
interfacing, operation outside of design limits, improper repair, or unauthorized modification. This WARRANTY is VOID if the unit shows evidence of having
been tampered with or shows evidence of having been damaged as a result of excessive corrosion; or current, heat, moisture or vibration; improper
specification; misapplication; misuse or other operating conditions outside of OMEGA’s control. Components in which wear is not warranted, include but
are not limited to contact points, fuses, and triacs.

OMEGA is pleased to offer suggestions on the use of its various products. However, OMEGA neither assumes responsibility for any
omissions or errors nor assumes liability for any damages that result from the use of its products in accordance with information
provided by OMEGA, either verbal or written. OMEGA warrants only that the parts manufactured by the company will be as specified
and free of defects. OMEGA MAKES NO OTHER WARRANTIES OR REPRESENTATIONS OF ANY KIND WHATSOEVER, EXPRESSED OR
IMPLIED, EXCEPT THAT OF TITLE, AND ALL IMPLIED WARRANTIES INCLUDING ANY WARRANTY OF MERCHANTABILITY AND FITNESS
FOR A PARTICULAR PURPOSE ARE HEREBY DISCLAIMED. LIMITATION OF LIABILITY: The remedies of purchaser set forth herein are
exclusive, and the total liability of OMEGA with respect to this order, whether based on contract, warranty, negligence, indemnification,
strict liability or otherwise, shall not exceed the purchase price of the component upon which liability is based. In no event shall OMEGA
be liable for consequential, incidental or special damages.

CONDITIONS: Equipment sold by OMEGA is not intended to be used, nor shall it be used: (1) as a “Basic Component” under 10 CFR 21 (NRC), used in or
with any nuclear installation or activity; or (2) in medical applications or used on humans. Should any Product(s) be used in or with any nuclear installation
or activity, medical application, used on humans, or misused in any way, OMEGA assumes no responsibility as set forth in our basic
WARRANTY/DISCLAIMER language, and, additionally, purchaser will indemnify OMEGA and hold OMEGA harmless from any liability or damage whatsoever
arising out of the use of the Product(s) in such a manner.

RETURN REQUESTS/INQUIRIES

Direct all warranty and repair requests/inquiries to the OMEGA Customer Service Department. BEFORE RETURNING ANY PRODUCT(S) TO OMEGA,
PURCHASER MUST OBTAIN AN AUTHORIZED RETURN (AR) NUMBER FROM OMEGA’S CUSTOMER SERVICE DEPARTMENT (IN ORDER TO AVOID
PROCESSING DELAYS). The assigned AR number should then be marked on the outside of the return package and on any correspondence.
The purchaser is responsible for shipping charges, freight, insurance and proper packaging to prevent breakage in transit.

OMEGA’s policy is to make running changes, not model changes, whenever an improvement is possible. This affords our customers the latest in technology and
engineering. OMEGA is a registered trademark of OMEGA ENGINEERING, INC.
© Copyright 2006 OMEGA ENGINEERING, INC. All rights reserved. This document may not be copied, photocopied, reproduced, translated, or reduced to any
electronic medium or machine-readable form, in whole or in part, without the prior written consent of OMEGA ENGINEERING, INC.

FOR NON-WARRANTY REPAIRS, consult OMEGA for current repair charges.
Have the following information available BEFORE contacting OMEGA:

1. Purchase Order number to cover the COST of the repair,

2. Model and serial number of the product, and

3. Repair instructions and/or specific problems relative to the product.

FOR WARRANTY RETURNS, please have the following information
available BEFORE contacting OMEGA:

1. Purchase Order number under which the product was PURCHASED,

2. Model and serial number of the product under warranty, and

3. Repair instructions and/or specific problems relative to the product.

OMEGAnet®Online Service

omega.com

Internet e-mail

[e-mail]

Servicing North America:

U.S.A.: One Omega Drive, P.O. Box 4047

ISO 9001 Certified

Stamford, CT 06907-0047
TEL: [phone]
FAX: [phone]

e-mail: [e-mail]

Canada: 976 Bergar

Laval (Quebec) H7L 5A1, Canada
TEL: [phone]
FAX: [phone]
e-mail: [e-mail]

For immediate technical or application assistance:

U.S.A. and Canada

: Sales Service: 1-800-826-6342/1-800-TC-OMEGA

®

Customer Service: 1-800-622-2378/1-800-622-BEST

®

Engineering Service: 1-800-872-9436/1-800-USA-WHEN

®

Mexico: En Español: [phone]-7803

e-mail: [e-mail]
FAX: [phone]
[e-mail]

Servicing Europe:

Czech Republic:

Frystatska 184, 733 01 Karviná, Czech Republic
TEL: [phone]
FAX: [phone]
Toll Free: 0800-1-66342
e-mail: [e-mail]

Germany/Austria: Daimlerstrasse 26, D-75392 Deckenpfronn, Germany

TEL: [phone]
FAX: [phone]
Toll Free in Germany: 0800 639 7678
e-mail: [e-mail]

United Kingdom: One Omega Drive, River Bend Technology Centre

ISO 9002 Certified

Northbank, Irlam, Manchester
M44 5BD United Kingdom
TEL: [phone]
FAX: [phone]
Toll Free in United Kingdom: 0800-488-488
e-mail: [e-mail]

It is the policy of OMEGA Engineering, Inc. to comply with all worldwide safety and EMC/EMI regulations that apply. OMEGA is constantly pursuing certification of its
products to the European New Approach Directives. OMEGA will add the CE mark to every appropriate device upon certification.

The information contained in this document is believed to be correct, but OMEGA accepts no liability for any errors it contains, and reserves the right to alter specifications without notice.
WARNING : These products are not designed for use in, and should not be used for, human applications.