Omega Products DP63800-E User Manual

DIGITAL PROCESS OR



STRAIN GAGE PANEL METERS

WITH BUILT IN EXCITATION

DP63800 Process Meters
DP63900 Strain Meters

Starts at

$

245

DP63800-E, $245, shown actual size.

⻬ Models Available for

Process Voltage and
Current or Strain
Gage Bridge Inputs

⻬ 5-Digit 0.56" Red

Sunlight Readable
Display

⻬ Variable Intensity

Display

⻬ 16 Point Scaling for

Non-linear Processes

⻬ Programmable

Function Keys/User
Inputs

⻬ Four Setpoint

Alarm Outputs
(W/Option Card)

⻬ Communication and

BUS Capabilities
(W/Option Card)

⻬ Retransmitted

Analog Output
(W/Option Card)

⻬ NEMA 4X IP65 Sealed

Front Bezel

See Section Y for a

Selection of Scientific,

Technical, and Reference

Books Available from

omega.com

The DP63000 Series panel meters
for process voltage and current or
strain gage bridge inputs offer many
features and performance
capabilities to suit a wide range of
industrial applications. The meters
employ a bright 14 mm (0.56"),
sunlight readable, red LED display.
The intensity of display can be
adjusted from dark room
applications up to sunlight
readable, making it ideal for
viewing in lighting conditions.

A standard green LED is available
as an option. They have been
specifically designed for harsh
industrial environments with NEMA
4X (IP65) sealed front bezel and
extensive testing of noise effects
to CE requirements.

The meters provide a MAX and MIN
reading memory with
programmable capture time. The
capture time is used to prevent
detection of false max or min
readings which may occur during
start-up or unusual process events.

A variety of field installable plug-in
option cards are also available to
enhance the unit’s capabilities.
Option boards are available for
setpoints/alarms, analog output
or serial communications.

SPECIFICATIONS

Display: 14.2 mm (0.56") red sunlight

readable LED, (standard green LED
optional)

Display Range: 5-Digit, -19999 to
99999 counts

D-55

Power Requirements:

Standard: 85 to 250 Vac, 50/60 Hz,

15 Va
“-LV” Option: 11 to 36 Vdc or
24 Vac ±10%, 50/60 Hz, 11 W)

Excitation:

Process: 24 Vdc @ 50 mA, ± 5%

regulated
Strain: selectable 5 Vdc @ 65 mA or

10 Vdc @ 125 mA (± 2%)

Keypad: 3 programmable function keys,
5 keys total

Operating Temperature Range:

0 to 50°C (32 to 122°F) derate to 45°C
(113°F) with 3 option boards installed

Storage Temperature Range:

-40 to 60°C (-40 to 140°F)

Operating and Storage Humidity:

0 to 85% max. RH (non-condensing)

Altitude: Up to 2000 meters
Enclosure Rating: IP65 Face only
Connections: High compression cage-

clamp terminal blocks
Dimensions: 96.5 x 49.5 x 106.6 mm

(3.80 x 1.95 x 4.20")
Panel Cutout: 92 x 45 mm (3.62 x 1.77")
Depth Behind Panel: 104.1 mm (4.10")
Weight: 295 g (10.4 oz)

OPTION BOARD
COMMUNICATIONS CARDS

RS232/RS485

Isolation to Sensor and User Input
Commons: 500 Vrms for 1 min

Working Voltage: 50V Not Isolated

from all other commons

Baud Rate: 300 to 19.2k
Data Format: 7/8 bits; odd, even, or

no parity working (Voltage: 50V)

RS232 Communication Card

Type: RS232 half duplex



v

49.5

(1.95)

96.5

(3.80)

91.4

(3.60)

44.5

(1.75)

2.5

(0.10)

104.1

(4.10)

44.5

(1.75)

Dimensions: mm (in)

Note: Recommended minimum clearance (behind the panel)
for mounting clip installation is 53.4 (2.1) H x 127 (5) W.

RS485 Communication Card

Type: RS485 multi-point balanced

interface
Bus Address: 0 to 99, max

32 meters per line
Transmit Delay: Selectable;

2 to 50 msec or 50 to 100 msec

MODBUS

Type: RS485; RTU and ASCII

MODBUS modes

Isolation to Sensor and User Input
Commons: 500 Vrms for 1 minute

Working Voltage: 50V, not isolated

from all other commons

Baud Rates: 300 to 38400
Data: 7/8 bits
Parity: No, Odd, or Even
Addresses: 1 to 247
Transmit Delay: Programmable

®

ANALOG OUTPUT CARD

Types (User Selectable): 0 to 20 mA,

4 to 20 mA and 0 to 10 Vdc

Isolation to Sensor and User Input
Commons: 500 Vrms for 1 min

Working Voltage: 50V Not isolated

from all other commons
Accuracy: 0.17% of FS (18 to

28°C); 0.4% of FS (0 to 50°C)

Resolution: 1/3500
Compliance:

10 Vdc: 10 kΩ load min
20 mA: 500 Ω load max

Update Time: 200 msec max to

within 99% of final readout value
(digital filter and internal zero
correction disabled) 700 msec max
(digital filter disabled, internal zero
correction enabled)

D-56

SETPOINT OUTPUT CARDS

(Four types of field installable cards)

Response Time: 200 msec max to

within 99% of final readout value
(digital filter and internal zero
correction disabled) 700 msec max
(digital filter disabled, internal zero
correction enabled)

Dual Relay Card (LDP6-CDS10):

Type: Two FORM-C relays
Isolation to Sensor and User Input

Commons: 2000 Vrms for 1 min
Working Voltage: 250V
Contact Rating: One Relay

Energized: 5 amps @ 120/240 Vac

or 28 Vdc (resistiveload),
@120 Vac, inductive load. Total
Current With Both Relays Energized
not to exceed 5 amps

Life Expectancy: 100 k cycles min
at full load rating. External RC
snubber extends relay life for
operation with inductive loads

Quad Relay Card (LDP6-CDS20):

Type: Four FORM-A relays
Isolation to Sensor and User Input

Commons: 2300 Vrms for 1 min
Working Voltage: 250V
Contact Rating: One Relay

Energized: 3 amps @ 250 Vac or

30 Vdc (resistive load),
120 Vac, inductive load. Total
Current With All Four Relays
Energized not to exceed 4 amps

Life Expectancy: 100 k cycles min
at full load rating. External RC
snubber extends relay life for
operation with inductive loads

Quad Sinking Open Collector
(LDP6-CDS30):

Type: Four isolated sinking NPN

transistors

Isolation to Sensor and User Input
Commons: 500 Vrms for 1 min

Working Voltage: 50V Not Isolated

from all other commons.
Rating: 100 mA max @ VSAT = 0.7V

max Vax = 30V

Quad Sourcing Open Collector
(LDP6-CDS40):

Type: Four isolated sourcing PNP

transistors

Isolation to Sensor and User Input
Commons: 500 Vrms for 1 min

Working Voltage: 50V

(Not Isolated from all other
commons

Rating: Internal supply: 24 Vdc
± 10%, 30 mA max total all four

External Supply: 30 Vdc max,
100 mA max each output

)

1

⁄

1

10

⁄8 HP

HP @

INSTRUMENTATION

D