Page 1
1
⁄8 DIN Temperature
Panel Meter
With Optional USB
Communications
DP6070 Series
U Modular USB,
RS232, RS485 Serial
Communication Options
and Relays
U J, K, T, E, R, S, B, N, C
Thermocouples
U 100 or 1000 Ω Platinum,
10 Ω Copper, 120 Ω
Nickel RTDs
U 1 or 0.1° Resolution
U Automatic Cold
Junction Compensation
U NEMA 4X (IP65) Front
U Universal 85 to 265 Vac
or 12/24 Vdc Input Power
U Large Dual-Line
6-Character Display,
15 and 12 mm
(0.60 and 0.46")
U Sunlight Readable
Display Models
U 2 or 4 Relays Plus
Isolated 4 to 20 mA
Output Options
U External 4-Relay and
Digital I/O Expansion
Modules
U Free Software for
Operation, Monitoring
and Programming
The DP6070 temperature
meter boasts specifications and
functionality that clearly makes
it one of the most advanced
temperature meters available.
It’s dual-line 6-character display,
function keys, and optional
expansion modules are only a few
of the special features available.
The DP6070 accepts many
thermocouple types and RTDs and
can be configured to have either
a 1° or 0.1° display resolution
on any type of sensor input. The
lower display makes configuration
simpler. The display itself is quite
configurable. There are many
relay functions for up to 8 relays;
including an Interlock Relay
function. The 4 to 20 mA output
can represent up to 12 different
parameters/variables. This makes
the DP6070 one of the most
versatile meters on the market.
Sunlight readable display models
have an extraordinarily bright
LED display. The upper display
can be programmed to indicate
current temperature, maximum or
minimum temperature, alternating
maximum/minimum temperatures,
one of eight alarm set points, or
MODBUS input. The lower display
can also be configured to display
engineering units, set points,
user defined legends, or simply
turned off. Input selection and
configuration are conveniently
set up via rear switches and
front panel programming. Three
levels of password protection
help maintain the reliability of the
programming.
General Specifications
Display: Both displays are 6 digits
(-99999 to 999999), red LEDs with
leading zero blanking
Upper Display: 15 mm (0.60") high
Lower Display: 12 mm (0.46") high
Display Intensity: 8 intensity levels
Display Update Rate: 5/second
(200 ms)
Overrange: Display flashes 999999
Underrange: Display flashes -99999
DP6070 shown smaller
than actual size.
M-1
Display Assignment: The upper
and lower displays may be assigned
to PV1, PV2, PCT (percent),
max/min, alternate max and min,
set points, units (lower display only),
or MODBUS input
Front Panel: NEMA 4X (IP65)
Programming Methods: 4 front
panel buttons, digital inputs, PC and
software, MODBUS registers, or
cloning using copy function
Noise Filter: Programmable from
2 to 199 (0 will disable filter)
Filter Bypass: Programmable from
0.1 to 99.9% of calibrated span
Recalibration: Calibrated at the
factory. Recalibration is recommended
at least every 12 months
Max/Min Display: Max (peak)/min
(valley) readings reached by the
process are stored until reset by
the user or until power to the meter
is cycled
Password: 3 programmable
passwords restrict modification of
programmed settings; Pass 1: Allows
use of function keys and digital
inputs; Pass 2: Allows use of function
keys, digital inputs and editing set/
reset points; Pass 3: Restricts all
programming, function keys, and
digital inputs
Non-Volatile Memory: All
programmed settings are stored in
non-volatile memory for a minimum
of ten years if power is lost
Power Options: 85 to 265 Vac
50/60 Hz, 90 to 265 Vdc, 20 W
maximum, or jumper selectable
12/24 Vdc ±10%, 15 W max
Fuse (External, Required): UL
recognized, 5 A max, slow blow; up
to 6 meters may share one 5 A fuse
M
Page 2
Isolated Transmitter Power Supply:
24 Vdc ±5% @ 200 mA maximum
(standard), (12/24 Vdc powered
models rated @ 100 mA maximum);
5 or 10 Vdc @ 50 mA maximum,
selectable with internal jumper J4
Normal Mode Rejection: Greater
than 60 dB at 50/60 Hz
Isolation: 4 kV input/output-to-power
line; 500V input-to-output or
output-to-P+ supply
Overvoltage Category: Installation
overvoltage category II, local level with
smaller transient overvoltages than
installation overvoltage category III
Operating Temperature Range:
-40 to 65°C (-40 to 149°F)
Storage Temperature Range:
-40 to 85°C (-40 to 185°F)
Relative Humidity: 0 to 90%
non-condensing
Connections: Removable screw
terminal blocks accept 12 to
22 AWG wire, RJ45 for external
relays, digital I/O, and serial
communication adaptors
Enclosure:
plastic, UL 94V-0, color: black
Mounting:
required: 92 x 45 mm (3.622 x
1.772"); two panel mounting bracket
assemblies are provided
Tightening Torque: Screw terminal
connectors: 5 lb-in (0.56 Nm)
Overall Dimensions:
119 W x 62 H x 143 mm D
(4.68 x 2.45 x 5.64")
Weight: 269 g (9.5 oz)
1
⁄8 DIN, high impact
1
⁄8 DIN panel cutout
Temperature Input
Input: Thermocouple J, K, T, E, R, S,
B, N, C; RTD 100 Ω platinum (0.00385
and 0.00392 curves), 10 Ω copper,
120 Ω nickel, 1000 Ω platinum
Input Impedance: Greater than 100 kΩ
Offset Adjust: User programmable
offset adjust ±50.0 degrees
Temperature Drift: ±2°C maximum
from 0 to 65°C ambient temperature;
±4°C maximum from -20 to 0°C
ambient temperature
Sensor Break: Display flashes
“open”, relays can be programmed to
go “on”, “off”, or to “ignore” (detected
as an upscale condition)
Averaging: Up to 10 RTDs connected
in parallel can be averaged
Accuracy and Range: See table above
Relays
Rating: 2 or 4 SPDT (Form C) internal
and/or 4 SPST (Form A) external;
rated 3 A @ 30 Vdc and 125/250 Vac
resistive load; 1/14 HP (≈ 50 W)
@ 125/250 Vac for inductive loads
such as contactors, solenoids, etc.
Noise Suppression: Recommended
for each relay contact switching
inductive loads
Deadband: 0 to 100% of span, user
programmable
High or Low Alarm: User may
program any alarm for high or low trip
point; unused alarm LEDs and relays
may be disabled (turned off)
Relay Operation: Automatic (nonlatching), latching (requires manual
acknowledge), sampling (based on
time), pump alternation control
(2 to 8 relays), off (disable unused
relays and enable interlock feature,
manual on/off control mode)
Time Delay: 0 to 999.9 seconds,
on and off relay time delays;
programmable and independent for
each relay
Fail-Safe Operation: Programmable
and independent for each relay
Note: Relay coil is energized in non-alarm
condition. In case of power failure, relay
will go to alarm state.
Auto Initialization: When power is
applied to the meter, relays will reflect
the state of the input to the meter
Serial Communications
Protocol: MODBUS RTU
Meter Address/Slave ID: 1 - 247
Baud Rate: 300 to 19,200 bps
Transmit Time Delay: Programmable
between 0 and 199 ms
Data: 8 bit (1 start bit, 1 or 2 stop bits)
Parity: Even, odd, or none with 1 or 2
stop bits
Byte-to-Byte Timeout:
0.01 to 2.54 seconds
Turn Around Delay:
Less than 2 ms (fixed)
Isolated 4 to 20 mA
Transmitter Output
Output Source: Process variable (PV),
max, min, set points 1 through 8, manual
control setting, or MODBUS input
Scaling Range: 1.000 to 23.000 mA
for any display range
Factory Calibration: 4.000 to
20.000 = 4 to 20 mA output
Analog Output Programming:
23.000 mA maximum for all
parameters: overrange, underrange,
max, min, and break
Accuracy: ± 0.1% of span ± 0.004 mA
Temperature Drift: 0.4 µA/°C maximum
from 0 to 65°C ambient, 0.8 µA/°C
maximum from -40 to 0°C ambient
Note: Analog output drift is separate from
input drift.
Isolated Transmitter Power Supply:
Terminals I+ & R: 24 Vdc ± 5% @
40 mA maximum, may be used to
power the 4 to 20 mA output or
other devices
External Loop Power Supply:
35 Vdc maximum
Output Loop Resistance:
24 Vdc Power Supply:
10Ω minimum, 700Ω maximum
35 Vdc (External) Power Supply:
100 Ω minimum, 1200 Ω maximum
Digital I/O Expansion
Module
Channels: 4 digital inputs and
4 digital outputs per module
System: Up to 2 modules for a total
of 8 inputs and 8 outputs
Digital Input Logic:
High: 3 to 5 Vdc
Low: 0 to 1.25 Vdc
Digital Output Logic:
High: 3.1 to 3.3 Vdc
Low: 0 to 0.4 Vdc
Source Current: 10 mA maximum
Sink Current: 1.5 mA minimum
+5 V Terminal: To be used as pull-up
for digital inputs only
4-Relay Expansion Module
Relays: 4 Form A (SPST) rated 3 A
@ 30 Vdc and 125/250 Vac resistive
load; 1/14 HP (≈ 50 W) @ 125/250
Vac for inductive loads
Type Range °C (°F) Accuracy
-129 to 1093 (-200 to 2000) ±1°C
-129 to 1316 (-200 to 2400) ±1°C
-129 to 400 (-200 to 752) ±1°C
-129 to 982 (-200 to 1800) ±1°C
-46 to 1649 (-50 to 3000) ±2°C
400 to 1816 (752 to 3300) ±2°C
-73 to 1260 (-100 to 2300) ±2°C
0 to 2260 (32 to 4100) ±2°C
10Ω Copper -200 to 260 (-328 to 500) ±0.1°C
100Ω Pt -200 to 850 (-328 to 1562) ±0.4°C
120Ω Nickel -79 to 260 (-110 to 500) ±0.1°C
1000Ω Pt -200 to 482 (-328 to 900) ±0.4°C
M-2
Page 3
Meter Copy
The Copy feature is used to copy (or
clone) all the settings from one DP6070
to other DP6070 meters in about
20 seconds! The Copy function is a
standard feature on all meters. It does
not require a communications adapter,
only an optional cable assembly, model
number DPA1200. See the ordering
information for complete details
NEMA 4X Field Enclosures
Thermoplastic NEMA 4X
enclosures are constructed for
either indoor or outdoor use.
DP6070 with DPA2812 NEMA 4X
field enclosure, shown smaller
than actual size.
Accessories
Model No. Description
DPA1004
DPA1044
DPA1232
DPA1485
DPA8008
DPA7485-I
DPA7485-N
DPA8232-N
DPA8485-I
DPA8485-N
DPA1002
DPA1200
DPA2811
DPA2812
Comes complete with 2 side mounting brackets, software, and operator’s manual.
Ordering Example: DP6070-6R2, temperature panel meter with 2 relays, and DPA8008, USB serial adaptor.
OCW-2, OMEGACARESM extends standard 3-year warranty to a total of 5 years.
4-relay expansion module - field installable
4 digital inputs and 4 digital outputs module - field installable
RS232 serial adaptor - field installable
RS485 serial adaptor - field installable
USB serial adaptor - field installable
RS232 to RS422/485 isolated converter - field installable
RS232 to RS422/485 non-isolated converter - field installable
USB to RS232 non-isolated converter - field installable
USB to RS422/485 isolated converter - field installable
USB to RS422/485 isolated converter - field installable
DIN rail mounting kit for 2 expansion modules
Meter copy cable
Plastic NEMA 4X enclosure for one DP6070 temperature meter
Plastic NEMA 4X enclosure for two DP6070 temperature meters
Model No. Description
Standard 85 to 265 Vac Models
DP6070-6R0
DP6070-6R2
DP6070-6R3
DP6070-6R4
DP6070-6R5
DP6070-6R7
Standard 12/24 Vdc Low Voltage Models
DP6070-7R0
DP6070-7R2
DP6070-7R3
Sunlight Readable Models, 85 to 265 Vac
DP6070-6H0
DP6070-6H2
DP6070-6H3
Sunlight Readable Models, 12/24 Vdc Low Voltage
DP6070-7H0
DP6070-7H2
DP6070-7H3
Temperature panel meter
Temperature panel meter with 2 relays
Temperature panel meter with 4 to 20 mA output
Temperature panel meter with 4 relays
Temperature panel meter with 2 relays and 4 to 20 mA output
Temperature panel meter with 4 relays and 4 to 20 mA output
Temperature panel meter
Temperature panel meter with 2 relays
Temperature panel meter with 4 to 20 mA output
Temperature panel meter
Temperature panel meter with 2 relays
Temperature panel meter with 4 to 20 mA output
Temperature panel meter
Temperature panel meter with 2 relays
Temperature panel meter with 4 to 20 mA output
M-3
To Order Visit omega.com/dp6070 for Pricing and Details
M
Loading...