Omega Products DP41-TBS Installation Manual

DP41-TBS Table Bench Stand

INSTRUCTION

SHEET

M2270/0710

The Table Bench Stand has three available uses: (a) as a tilt stand for benchtop use, (b) as a carrying handle for portability, (c) folded flat for table and panel mount use.

To assemble:

1. Unplug the meter from the power source.

2. Remove the rear screw and cover.

3. Remove all wire connections. Be sure to label wiring sequence.

4. Remove the two thumb nuts.

5. Slide TBS sleeve onto meter.

6. Screw on the two thumb nuts.

7. Reconnect wire and connections.

8. Re-install rear cover.

13105ML-99 B

WARRANTY/DISCLAIMER

OMEGA ENGINEERING, INC. warrants this unit to be free of defectsin materials and workmanship for a period of one (1) year from the date of

purchase. In addition to OMEGA’sstandard warranty period, OMEGA Engineering will extend the warrantyperiod for one (1) additional year if

If the unit malfunctions, it must be returned tothefactory for evaluation. OMEGA’sCustomerServiceDepartment will issue an Authorized Return

the warranty card enclosed with each instrument is returned to OMEGA.

(AR) number immediately upon phone or written request. Upon examination by OMEGA, if the unit is found to be defective, it will be repaired

or replaced at no charge. OMEGA’s WARRANTY does not apply to defects resulting from any action of the purchaser, including but not limited

to mishandling, improper interfacing, operationoutside of design limits, improper repair, or unauthorizedmodification.This WARRANTY is VOID

if the unit shows evidence of having beentampered with or shows evidence of having been damaged as a result of excessive corrosion; or cur-

rent, heat, moisture or vibration; improper specification; misapplication; misuse or other operating conditions outside of OMEGA’s control.

Components which wear are not warranted, including but not limited to contact points, fuses, and triacs.

OMEGA is pleased to offer suggestions on the use of its various products. However, OMEGA neither assumes responsibility for any

omissions or errors nor assumes liability for any damages that result from the use ofits products in accordance with information pro-

vided by OMEGA, either verbal or written. OMEGA warrants only that the parts manufactured by it will be as specified and free of

defects. OMEGA MAKES NO OTHER WARRANTIES OR REPRESENTATIONS OF ANY KIND WHATSOEVER, EXPRESS OR IMPLIED,

EXCEPT THAT OF TITLE, AND ALL IMPLIED WARRANTIES INCLUDING ANY WARRANTY OF MERCHANTABILITY AND FITNESS FOR

A PARTICULAR PURPOSE ARE HEREBY DISCLAIMED. LIMITATION OF LIABILITY: The remedies of purchaser set forth herein are

exclusive, and the total liability of OMEGA with respect to this order, whether based on contract, warranty, negligence, indemnifica-

tion, strict liability or otherwise, shall not exceed the purchase price of the component upon which liability is based. In no event shall

OMEGA be liable for consequential, incidental or special damages.

CONDITIONS: Equipment sold by OMEGAis not intended to be used, nor shall it be used: (1) as a “Basic Component” under 10 CFR

consult OMEGA for current repair

charges. Have the following information available BEFORE contact-

ing OMEGA:

1. Purchase Order number to cover the COST of the repair,

2. Model and serial number of product, and

3. Repair instructions and/or specific problems relative to the prod-

FOR NON-WARRANTY REPAIRS,

uct.

, and are Trademarks of OMEGA ENGINEERING, INC.

RETURN REQUESTS/INQUIRIES

, omega.com

the product.

PURCHASED,

Direct all warranty and repair requests/inquiries to the OMEGA Customer Service Department. BEFORE RETURNING ANY

SERVICE DEPARTMENT (IN ORDER TO AVOID PROCESSING DELAYS). The assigned AR number should then be marked on the

outside of the return package and on anycorrespondence.

PRODUCT(S) TO OMEGA, PURCHASER MUST OBTAIN AN AUTHORIZED RETURN (AR) NUMBER FROM OMEGA’S CUSTOMER

21 (NRC), used in or with any nuclear installation or activity; or (2) in medical applications or used on humans. Should any Product(s) be

used in or with any nuclear installation or activity, medical application, used on humans, or misused in any way, OMEGA assumes no

responsibility as set forth in our basic WARRANTY/DISCLAIMER language, and, additionally, purchaser will indemnify OMEGAand hold

OMEGA harmless from any liability or damage whatsoever arising out of the use of the Product(s) in such a manner.

The purchaser is responsible for shipping charges, freight,insurance and proper packaging to prevent breakage in transit.

available BEFORE contacting OMEGA:

1. Purchase Order number under which the product was

FOR WARRANTY RETURNS, please have the following information

2. Model and serial number of the product under warranty, and

3. Repair instructions and/or specific problems relative to

OMEGA’s policy is to make running changes, not model changes, whenever an improvement is possible. This affords our customers the latest

in technology and engineering.

reducedtoanyelectronic medium or machine-readable form,in wholeorin part,without the prior written consentofOMEGAENGINEERING,INC.

TRADEMARK NOTICE: