Omega Products CN1001-TC User Manual

Begin Operation

Exit the Configuration MENU and
reinitialize the meter.

• Press RESET twice, or

• Press MENU until RST flashes on
the display.

When the temperature appears, the meter is up and
running.

Changing Setpoint Values

1. While in RUN mode, press SETPTS. The controller
displays the current value for setpoint 1:

You can change setpoint 1 or press SETPTS again to
show the current value for setpoint 2.

2. To change the setpoint 1 value:

• Press



/DEV until the digit(s) you want to change

flashes on the display.

• Press



/MAX to change the value.

• Press SETPTS to store the value
shown. The current value for setpoint
2 is shown:

3. Change setpoint 2 using the procedure above, or just
press SETPTS to return to RUN mode.

To Set the Decimal Point

1. If it's not already shown, press MENU
until the unit displays:

2. Press



/DEV. The unit displays:

3. Press



/MAX to move the decimal
point to the desired location. The
choices are FFFF. and FFF.F.

4. Press MENU to select the decimal
point position shown. The unit displays:

To Set the Temperature Unit
(Fahrenheit or Celsius):

1. If it’s not already shown, press MENU
until the unit displays:

2. Press



/DEV. The unit displays:

3. Press



/MAX to display the setting

you want. Choices are F and C.

4. Press MENU to select the temperature
until shown.The unit displays:

CN1001-TC

Temperature Controller with
Time Proportional Control

56

MQS1610/0606 12342ML-98 Rev. B

This device is marked with the international caution symbol. It is important
to read the Setup Guide before installing or commissioning this device as
it contains important information relating to safety and EMC.

It is the policy of OMEGA to comply with all worldwide safety and EMC/EMI
regulations that apply. OMEGA is constantly pursuing certification of its products to
the European New Approach Directives. OMEGA will add the CE mark to every
appropriate device upon certification.

The information contained in this document is believed to be correct but OMEGA
Engineering, Inc. accepts no liability for any errors it contains, and reserves the right
to alter specifications without notice.

TRADEMARK NOTICE:

omega.com

™

, and ,

are

trademarks of OMEGA Engineering, Inc.

®

WARNING: These products are not designed for use in, and should not be used
for, patient connected applications.

WARRANTY/DISCLAIMER

OMEGA ENGINEERING, INC. warrants this unit to be free of defects in
materials and workmanship for a period of one (1) year from the date of
purchase. In addition to OMEGA’s standard warranty period, OMEGA
Engineering will extend the warranty period for

four (4) additional years if the

warranty card enclosed with each instrument is returned to OMEGA.

If the unit should malfunction, it must be returned to the factory for evaluation.
OMEGA’s Customer Service Department will issue an Authorized Return (AR)
number immediately upon phone or written request. Upon examination by
OMEGA, if the unit is found to be defective it will be repaired or replaced at no
charge. Omega's WARRANTY does not apply to defects resulting from any
action of the purchaser, including but not limited to mishandling, improper
interfacing, operation outside of design limits, improper repair, or unauthorized
modification. This WARRANTY is VOID if the unit shows evidence of having
been tampered with or shows evidence of being damaged as a result of
excessive corrosion; or current, heat, moisture or vibration; improper
specification; misapplication; misuse or other operating conditions outside of
OMEGA’s control. Components which wear are not warranted, including but
not limited to contact points, fuses, and triacs.

OMEGA is pleased to offer suggestions on the use of its various
products. However, OMEGA neither assumes responsibility for any
omissions or errors nor assumes liability for any damages that result
from the use if its products in accordance with information provided by
OMEGA, either verbal or written. OMEGA warrants only that the parts
manufactured by it will be as specified and free of defects. OMEGA
MAKES NO OTHER WARRANTIES OR REPRESENTATIONS OF ANY
KIND WHATSOEVER, EXPRESSED OR IMPLIED, EXCEPT THAT OF
TITLE, AND ALL IMPLIED WARRANTIES INCLUDING ANY WARRANTY
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
ARE HEREBY DISCLAIMED. LIMITATION OF LIABILITY: The remedies
of purchaser set forth herein are exclusive and the total liability of
OMEGA with respect to this order, whether based on contract,
warranty, negligence, indemnification, strict liability or otherwise, shall
not exceed the purchase price of the component upon which liability is
based. In no event shall OMEGA be liable for consequential, incidental
or special damages.

CONDITIONS: Equipment sold by OMEGA is not intended to be used, nor
shall it be used: (1) as a “Basic Component” under 10 CFR 21 (NRC), used in
or with any nuclear installation or activity; or (2) in medical applications or
used on humans. Should any Product(s) be used in or with any nuclear
installation or activity, medical application, used on humans, or misused in any
way, OMEGA assumes no responsibility as set forth in our basic WARRANTY
/ DISCLAIMER language, and additionally, purchaser will indemnify OMEGA
and hold OMEGA harmless from any liability or damage whatsoever arising
out of the use of the Product(s) in such a manner.

RETURN REQUESTS / INQUIRIES

Direct all warranty and repair requests/inquiries to the OMEGA Customer Service
Department. BEFORE RETURNING ANY PRODUCT(S) TO OMEGA, PURCHASER
MUST OBTAIN AN AUTHORIZED RETURN (AR) NUMBER FROM OMEGA’S
CUSTOMER SERVICE DEPARTMENT (IN ORDER TO AVOID PROCESSING
DELAYS). The assigned AR number should then be marked on the outside of the
return package and on any correspondence.

The purchaser is responsible for shipping charges, freight, insurance and proper
packaging to prevent breakage in transit.

FOR WARRANTY RETURNS, please
have the following information available
BEFORE contacting OMEGA:

1. P.O. number under which the
product was PURCHASED,

2. Model and serial number of the
product under warranty, and

3. Repair instructions and/or specific
problems relative to the product.

FOR

NON-WARRANTY REPAIRS,
consult OMEGA for current repair
charges. Have the following information
available BEFORE contacting OMEGA:

1. P.O. number to cover the COST of

the repair,

2. Model and serial number of product,

and

3. Repair instructions and/or specific

problems relative to the product.

OMEGA’s policy is to make running changes, not model changes, whenever an
improvement is possible. This affords our customers the latest in technology and
engineering.

OMEGA is a registered trademark of OMEGA ENGINEERING, INC.
© Copyright 2006 OMEGA ENGINEERING, INC. All rights reserved.

This document may not be copied, photocopied, reproduced, translated, or reduced
to any electronic medium or machine-readable form, in whole or in part, without
prior written consent of OMEGA ENGINEERING, INC.

PATENT NOTICE: The “Meter Case Bezel Design” is a trademark of
NEWPORT Electronics, Inc., registered in the U.S. USED UNDER LICENSE.
This product is covered by one or more of the following patents: U.S. Pat. No.
Des. 336,895; 5,274,577 / CANADA 2052599; 2052600 / ITALY 1249456;
1250938 / FRANCE BREVET No. 91 12756 / SPAIN 2039150; 2048066 /
UK PATENT No. GB2 249 837; GB2 248 954 / GERMANY DE 41 34398 C2.
OTHER INTERNATIONAL PATENTS PENDING.

®

®

OMEGAnet¤ On-Line Service

www.omega.com

Servicing North America:

USA: One Omega Drive, P.O. Box 4047

ISO 9001 Certified Stamford CT 06907-0047

 TEL: [phone] FAX: [phone]
 e-mail: [e-mail]

Canada:  976 Bergar
 Laval (Quebec) H7L 5A1
 TEL: [phone] FAX: [phone]
 e-mail: [e-mail]

For immediate technical or application assistance:

USA and Canada: Sales Service: 1-800-826-6342 / 1-800-TC-OMEGA

 Customer Service: 1-800-622-2378 / 1-800-622-BEST
 Engineering Service: 1-800-872-9436 / 1-800-USA-WHEN

Mexico and  TEL: (001)800-TC-OMEGA® FAX: [phone]
Latin American: En Espa

 e-mail: [e-mail]

ñol: [phone]-7803

Servicing Europe:

Czech Republic: Frystatska 184, 733 01 Karviná

 TEL: [phone] FAX: [phone]
 e-mail: [e-mail]

Germany/Austria: Daimlerstrasse 26, D-75392 Deckenpfronn, Germany
 TEL: [phone] FAX: [phone]
 Toll Free in Germany: 0800 639 7678
 e-mail: [e-mail]

United Kingdom: One Omega Drive

ISO 9002 Certified River Bend Technology Centre

 Northbank, Irlam Manchester M44 5BD United Kingdom
 TEL: [phone] FAX: [phone]
 Toll Free in England: 0800 488 488
 e-mail: [e-mail]

Internet e-mail

[e-mail]

MADE IN

USA

®

®

®

Using This Quick Start Manual

Use this Quick Start Manual to set up your Controller and
begin operation. Information is provided on how to:

• Connect ac power

• Connect the thermocouple

• Set basic options for operation

For complete information on all setup options, please refer
to the Operator's Manual.

Before You Begin

In addition to the controller and the related parts, you will
need the following items to set up your unit:

• ac power, as listed on the units ID/Product Label

• Thermocouple

• 1/8-inch flat-blade screwdriver.

Mount the Unit

1. Cut a panel opening
using the dimensions
shown to the right.

2. Position the unit in the
opening, making sure
the front bezel gasket
is flush to the panel.

3. Slide on mounting
bracket to secure.

Connect ~ AC Power

1. Remove the panel at the back of the unit.

2. Locate the TB1 connector.

Main ~ ac Power Connections

START HERE

2

34

Connect the Thermocouple

1. Locate the Thermocouple connector on the rear of the
unit. Refer figure below for location.

2. Attach the thermocouple wires.

• Connect positive (+) lead of thermocouple.

• Connect negative (-) red lead of thermocouple.

3. Tighten the lockdown screws. The following figure
shows the correct wiring.

4. Tug gently on the wires to verify the connections.

5. Replace the panel at the back of the unit.

Thermocouple Input Connection..

Turn On the Unit

1. Apply ac power to the unit.

As the unit initializes, flashing RST and then T/C on
the front panel. Then the temperature should appear.

2. Verify that a temperature is displayed. If not:

• Remove ac power

• Verify the TB1 power connections

• Check your power source

• Apply ac power again.

Configure the Unit

To configure the unit, you use the buttons on the front
panel.

To: Take This Action:

Display the Press the MENU button. The first
Configuration on the menu, INPT, displays.
Menu

Select a submenu 1. Press MENU until the function
function you want is shown.

2. Press



/DEV.

The information you can change
begins to flash.

Select a value 1. Press



/MAX to display the
for that submenu option you want.
function

2. Press MENU to select it.

The message STRD quickly
flashes, indicating that the
selection has been stored in
memory. Then the next menu
function displays.

Go back to the Press RESET once.
previous menu
function

Exit the Press RESET twice. The unit
Configuration reinitializes (displays RST, then

T/C). When the temperature
displays,

the unit is back in run

mode.

(Optionally, you can press MENU
to move through all the menu
functions until the unit reinitializes.)

To Set the Thermocouple Type:

1. Press MENU until the unit displays:

2. Press



/DEV. The unit displays:

3. Press



/MAX until the
thermocouple for your
installation is shown.

Choices are J.TC, K.TC, T.TC,
DJ.TC

4. Press MENU to select the thermocouple shown.
The unit displays:

Warning: Do not connect ac power to your meter
until you have completed all input and output
connections. Failure to do so may result in injury!

3. Insert the correct wire in
each terminal as shown
in the following figure
and tighten the lockdown
screws.

4. Tug gently on the wires
to verify the connections.

VERSION 1

TB1

TB3A

TB3B

108791112 798

-+ -+

VERSION 2

TB1

4312563421

65

10

1211

##

TB4B

TB4C

TB4 PINS A & B
NOT AVAILABLE FOR
SINGLE T/C MODEL