Omega Products CN1000-RTD User Manual

Using This Quick Start Manual

Use this Quick Start Manual to set up your controller
and begin operation. Information is provided on how to:
¥ Connect ac power

¥ Connect the RTD

¥ Set basic options for operation

For complete information on all setup options, see the
OperatorÕs Manual.

Before You Begin

In addition to the meter and the related parts, you will
need the following items to set up your meter:

¥ ac power, as listed on meterÕs ID/Power Label

¥ RTD

¥

1

Ú8Ó flat blade screwdriver

Mount the Meter

1. Cut a panel opening
using the dimensions
shown here.

2. Position the meter in
the opening, making
sure the front bezel is flush with the panel.

Connect ac Power

Warning: Do not connect ac power to your meter
until you have completed all input and output
connections. Failure to do so may result in injury!

1. Remove the panel at the back of the meter.

2. Locate the TB1 connector.

3. Insert the correct wire in each terminal and tighten
the lockdown screws. Tug gently on the wires to
verify connections.

Main ac Power Connections

To: Take This Action

Select a value 1. Press 䊳/MAX. to display
for that submenu the option you want.
function. 2. Press MENU to select it.

The message STRD quickly
flashes, indicating that the
selection has been stored in
memory. Then the next
menu function displays.

Go back to the Press RESET once.
previous menu
function.

Exit the meter ¥ Press RESET twice. The
Configuration reinitializes (displays RST,
Menu. then RTD). When the

temperature displays, the
meter is back in run mode.

¥ Optionally, you can press

MENU to move through all
the menu functions until the
meter reinitializes.

To Set the RTD Type:

1. Press MENU until the meter
displays:

2. Press 䊳/DEV. The meter
displays:

3. Press

䊱

/MAX until the RTD

for your installation is shown.

¥ RTD.2 is for a 2-wire RTD

¥ RTD.3 is for a 3-wire RTD

¥ RTD.4 is for a 4-wire RTD

4. Press MENU to select the RTD shown. The
meter displays:

4-Wire RTD Input Connection

Turn on the Meter

1. Apply ac power to the meter. The meter initializes,
flashing RST then RTD on the front panel. Then
the temperature should appear.

2. Verify that a temperature is displayed. If not:

¥ Remove ac power

¥ Verify the TB1 power connections

¥ Check your power source

¥ Apply ac power again

Configure the Meter

To configure the meter, use the buttons on the front
panel.

To: Take This Action

Display the Press the MENU button.
Configuration The first function on the
Menu. menu, INPT, displays.

Select the 1. Press MENU until the
sub-menu function you want is shown.
(a function you 2. Press 䊳/DEV.
want to perform).

The information you can change
begins to flash.

Connecting the RTD

1. Locate the TB2 connector on the rear of the
meter.

2. Attach the RTD wires, referring to the appropriate
diagram below and tighten down lockdown
screws.

3. Tug gently on the wires to verify the connections.

4. Replace the panel at the back of the meter.

2-Wire RTD Input Connection

3-Wire RTD Input Connection

START HERE

2

34

12504ML-98A_CN1000-RTD_OMG.qxd 8/13/99 11:29 AM Page 1

TB1

8978765

10 11 12

NEUTRAL

LINE

FUSE

VERSION #1

TB2

6543214321

EARTH
GROUND

AC POWER

PANEL THICKNESS

6,4 (.25) MAX
0,8 (.03) MIN

1,5

R(.06)

45,00 + 0,61/-0,00

(1.772 + .024/Ð.000)

4 PLCS

92,00 + 0,81/Ð0,00

(3.622 + .032/Ð.000)

NOTE: Dimensions in Millimeters (Inches)

VERSION #2

TB1

654321

8978765

TB2 PINS 1 THRU 4
NOT AVAILABLE FOR
SINGLE RTD MODEL

TB2

10 11 12

TB2

VERSION #1

+E

1

3

2

5 6

RTD

TB2

VERSION #1

+E

1

3

2

5 6

RTD

7

7

+R

-S

+R

4

4

TB2

VERSION #1

+E

2 3

516

7

+R

4

8

+S

TB2

VERSION #2

3 4

51627

+E1-S -R

+S1

-S1

8

-E1

TB2

VERSION #2

RTD

RTD

152

8

-R+S -S

+E1

+S1

6

374

-S1 -E1

8

RTD

TB2

VERSION #2

152

8

374

6

8

䊱䊳

/MAX

SETPTS /DEV MENU RESET

䊱䊳

/MAX

SETPTS /DEV MENU RESET

+S1

-R+S

+E1

-S1 -E1

䊱䊳

/MAX

SETPTS /DEV MENU RESET

RTD

䊱䊳

/MAX

SETPTS /DEV MENU RESET

䊱䊳

/MAX

SETPTS /DEV MENU RESET

To Set the Decimal Point Position:

1. If it's not already shown, press
MENU until the meter shows:

2. Press 䊳/DEV. The meter
displays:

3. Press

䊱

/MAX to move the
decimal point to the desired
location. Choices are: FFFF.
or FFF.F.

4. Press MENU to select the decimal point position
shown. The meter displays:

To Select the Temperature Unit
(Fahrenheit or Celsius):

1. If it's not already shown, press
MENU until the meter shows:

2. Press

䊳

/DEV. The meter

displays:

3. Press

䊱

/MAX to display the
setting you want. Choices are
F and C.

4. Press MENU to select the temperature meter
shown.
The
meter
displays:

56

Begin Operation

Reinitialize the meter (press
RESET twice or press MENU
until RST flashes on the display).

When the temperature appears,
the meter is up and running.

Changing Setpoint Values:

1. While in RUN mode, press SETPTS. The unit
displays setpoint 1:

You can change setpoint 1 or press SETPTS
again to show the current value for setpoint 2.

2. To change the setpoint 1 value:

¥ Press

䊳

/DEV until the digit(s) you want to

change flashes on the display.

¥ Press

䊱

/MAX to change the value.

¥ Press SETPTS to store the value shown. The

current value for setpoint 2 is shown:

3. When setpoint 2 appears, you can change it using
the procedure above or press SETPTS to return
to RUN mode.

MQS1609/0899 12504ML-98 Rev. A

WARRANTY/DISCLAIMER

OMEGA Engineering, Inc. warrants this unit to be free of defects in materials
and workmanship for a period of

13 months

from date of purchase. OMEGA

Warranty adds an

additional one (1) month

grace period to the normal

one (1)

year

product warranty to cover handling and shipping time. This ensures that

OMEGAÕs customers receive maximum coverage on each product.

If the unit should malfunction, it must be returned to the factory for evaluation.
OMEGAÕs Customer Service Department will issue an Authorized Return (AR)
number immediately upon phone or written request. Upon examination by
OMEGA, if the unit is found to be defective it will be repaired or replaced at no
charge. Omega's WARRANTY does not apply to defects resulting from any
action of the purchaser, including but not limited to mishandling, improper
interfacing, operation outside of design limits, improper repair, or unauthorized
modification. This WARRANTY is VOID if the unit shows evidence of having
been tampered with or shows evidence of being damaged as a result of
excessive corrosion; or current, heat, moisture or vibration; improper
specification; misapplication; misuse or other operating conditions outside of
OMEGAÕs control. Components which wear are not warranted, including but
not limited to contact points, fuses, and triacs.

OMEGA is pleased to offer suggestions on the use of its various
products. However, OMEGA neither assumes responsibility for any
omissions or errors nor assumes liability for any damages that result
from the use if its products in accordance with information provided by
OMEGA, either verbal or written. OMEGA warrants only that the parts
manufactured by it will be as specified and free of defects. OMEGA
MAKES NO OTHER WARRANTIES OR REPRESENTATIONS OF ANY
KIND WHATSOEVER, EXPRESSED OR IMPLIED, EXCEPT THAT OF
TITLE, AND ALL IMPLIED WARRANTIES INCLUDING ANY WARRANTY
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
ARE HEREBY DISCLAIMED. LIMITATION OF LIABILITY: The remedies
of purchaser set forth herein are exclusive and the total liability of
OMEGA with respect to this order, whether based on contract,
warranty, negligence, indemnification, strict liability or otherwise, shall
not exceed the purchase price of the component upon which liability is
based. In no event shall OMEGA be liable for consequential, incidental
or special damages.

CONDITIONS: Equipment sold by OMEGA is not intended to be used, nor
shall it be used: (1) as a ÒBasic ComponentÓ under 10 CFR 21 (NRC), used in
or with any nuclear installation or activity; or (2) in medical applications or
used on humans. Should any Product(s) be used in or with any nuclear
installation or activity, medical application, used on humans, or misused in any
way, OMEGA assumes no responsibility as set forth in our basic WARRANTY
/ DISCLAIMER language, and additionally, purchaser will indemnify OMEGA
and hold OMEGA harmless from any liability or damage whatsoever arising
out of the use of the Product(s) in such a manner.

RETURN REQUESTS / INQUIRIES

Direct all warranty and repair requests/inquiries to the OMEGA Customer Service
Department. BEFORE RETURNING ANY PRODUCT(S) TO OMEGA,
PURCHASER MUST OBTAIN AN AUTHORIZED RETURN (AR) NUMBER
FROM OMEGAÕS CUSTOMER SERVICE DEPARTMENT (IN ORDER TO AVOID
PROCESSING DELAYS). The assigned AR number should then be marked on
the outside of the return package and on any correspondence.

The purchaser is responsible for shipping charges, freight, insurance and proper
packaging to prevent breakage in transit.

FOR W

ARRANTY RETURNS,
please have the following information
available BEFORE
contacting OMEGA:

1. P.O. number under which the

product was PURCHASED,

2. Model and serial number of the

product under warranty, and

3. Repair instructions and/or specific

problems relative to the product.

FOR NON-W

ARRANTY REPAIRS,
consult OMEGA for current repair
charges. Have the following
information available BEFORE
contacting OMEGA:

1. P.O. number to cover the COST of

the repair,

2. Model and serial number of product,

and

3. Repair instructions and/or specific

problems relative to the product.

OMEGAÕs policy is to make running changes, not model changes, whenever an
improvement is possible. This affords our customers the latest in technology and
engineering.

OMEGA is a registered trademark of OMEGA ENGINEERING, INC.
© Copyright 1999 OMEGA ENGINEERING, INC. All rights reserved.

This document may not be copied, photocopied, reproduced, translated, or
reduced to any electronic medium or machine-readable form, in whole or in
part, without prior written consent of OMEGA ENGINEERING, INC.

PATENT NOTICE: The ÒMeter Case Bezel DesignÓ is a trademark of
NEWPORT Electronics, Inc., registered in the U.S. USED UNDER LICENSE.
This product is covered by one or more of the following patents: U.S. Pat. No.
Des. 336,895; 5,274,577 / CANADA 2052599; 2052600 / ITALY 1249456;
1250938 / FRANCE BREVET No. 91 12756 / SPAIN 2039150; 2048066 /
UK PATENT No. GB2 249 837; GB2 248 954 / GERMANY DE 41 34398 C2.
OTHER INTERNATIONAL PATENTS PENDING.

This device is marked with the international caution symbol. It is important
to read the Setup Guide before installing or commissioning this device as
it contains important information relating to safety and EMC.

It is the policy of OMEGA to comply with all worldwide safety and EMC/EMI
regulations that apply. OMEGA is constantly pursuing certification of its products to
the European New Approach Directives. OMEGA will add the CE mark to every
appropriate device upon certification.

The information contained in this document is believed to be correct but OMEGA
Engineering, Inc. accepts no liability for any errors it contains, and reserves the right
to alter specifications without notice.

TRADEMARK NOTICE:

omega.com

™

, and ,

are

trademarks of OMEGA Engineering, Inc.

®

WARNING: These products are not designed for use in, and should not be used
for, patient connected applications.

CN1000-RTD

TEMPERATURE CONTROLLER WITH
TIME PROPORTIONAL CONTROL

OMEGAnet¨ On-Line Service Internet e-mail

http://www.omega.com [e-mail]

Servicing North America:

USA: One Omega Drive, P.O. Box 4047
ISO 9001 Certified

Stamford, CT 06907-0047
Tel: [phone] FAX: [phone]
e-mail: [e-mail]

Canada: 976 Bergar

Laval (Quebec) H7L 5A1
Tel: [phone] FAX: [phone]
e-mail: [e-mail]

For immediate technical or application assistance:

USA and Canada: Sales Service: 1-800-826-6342 / 1-800-TC-OMEGA

¨

Customer Service: 1-800-622-2378 / 1-800-622-BEST

¨

Engineering Service: 1-800-872-9436 / 1-800-USA-WHEN

¨

TELEX: 996404 EASYLINK: 62968934 CABLE: OMEGA

Mexico TEL: [phone] FAX: [phone]

En Espa–ol: [phone]-7803
e-mail: [e-mail]

Servicing Europe:

Benelux: Postbus 8034, 1180 LAAmstelveen, The Netherlands

Tel: [phone] FAX: [phone]
Toll Free in Benelux: 0800 0993344
e-mail: [e-mail]

Czech Republic: RudŽ arm‡dy 1868, 733 01 Karvin‡ 8

Tel: [phone] FAX: [phone]
e-mail: [e-mail]

France: 9, rue Denis Papin, 78190 Trappes

Tel: [phone] FAX: [phone]
Toll Free in France: 0800406342
e-mail: [e-mail]

Germany/Austria: Daimlerstrasse 26, D-75392 Deckenpfronn, Germany

Tel: [phone] FAX: [phone]
Toll Free in Germany: 0800 TC-OMEGA

SM

e-mail: [e-mail]

United Kingdom: One Omega Drive,
ISO 9002 Certified

River Bend Technology Centre
Northbank, Irlam
Manchester M44 5EX United Kingdom
Tel: [phone] FAX: [phone]
Toll Free in United Kingdom: 0800 488 488
e-mail: [e-mail]

12504ML-98A_CN1000-RTD_OMG.qxd 8/13/99 11:29 AM Page 2

䊱䊳

/MAX

SETPTS /DEV MENU RESET

䊱䊳

/MAX

SETPTS /DEV MENU RESET

䊱䊳

/MAX

SETPTS /DEV MENU RESET

䊱䊳

/MAX

SETPTS /DEV MENU RESET

䊱䊳

/MAX

SETPTS /DEV MENU RESET

䊱䊳

/MAX

SETPTS /DEV MENU RESET

䊱䊳

/MAX

SETPTS /DEV MENU RESET

䊱䊳

/MAX

SETPTS /DEV MENU RESET

䊱䊳

/MAX

SETPTS /DEV MENU RESET

䊱䊳

/MAX

SETPTS /DEV MENU RESET

䊱䊳

/MAX

SETPTS /DEV MENU RESET

䊱䊳

/MAX

SETPTS /DEV MENU RESET

QUICK START

䊱䊳

/MAX

SETPTS /DEV MENU RESET

䊱䊳

/MAX

SETPTS /DEV MENU RESET

䊱䊳

/MAX

SETPTS /DEV MENU RESET