Eat well, drink well and live well with Omega www.omegajuicers.com
VRT400 SERIES
Product Contents
OMEGA PRODUCTS, INC.
6291 LYSTER LANE
HARRISBURG, PA 17111-4523 U.S.A.
PHONE: 1.800.633.3401
FAX: 717.561.1298
May 2013
English, May 3013
PLEASE READ THESE INSTRUCTIONS CAREFULLY BEFORE USE
IMPORTANT SAFEGUARDS
IMPORTANT SAFEGUARDS
Please read carefully before using. Follow instructions
to avoid injury.
• To protect against risk of electrical shock or re, do not
put motor base, cord, or plug in water and keep them dry
at all times.
• Do not disassemble the base. All repairs should be made
only by authorized personnel.
• Check voltage to be sure that the voltage indicated on the
name plate agrees with your voltage.
• Close adult supervision is necessary when appliance is used
by or near children.
• Unplug the power cord from the wall outlet when the appliance
is not in use.
• Do not operate any appliance with a damaged cord/plug,
a malfunctioning unit, or after the unit is dropped or damaged
in any manner.
• The use of attachments not recommended may cause damage,
re, shock, or injury.
• Keep hands and utensils out of unit when motor is running
to prevent the possibility of severe personal injury or damage
to the appliance.
Additional usage precautions:
• Do not pre-operate before inputting food. Doing so may
cause a normal squeaking noise.
• Do not attempt to juice any hard materials, large seeds
(seeds which can not be swallowed or chewed), pits, ice,
or frozen foods.
• If food gets stuck in the feeding tube, do not use anything
other than the recommended pusher.
• Do not use for more than 30 minutes continuously
(only meant for household use).
SAVE THESE INSTRUCTIONS
• Do not attempt to disassemble any attachments while the motor
is running. Lift appliance with two hands (appliance weight
approximately 14 lbs.)
• Do not put any parts into the dishwasher or use hard scouring
powders and hard implements. Exposure to high heat can
cause damage.
Omega Juicer Manual For Household Use
(Warranty Included)
1. Read “Precautions for safe use (Page 4)” carefully and use
the appliance properly.
2. Save these instructions.
3. Check if the voltage indicated on the base of the appliance
corresponds to the local voltage before you connect
the appliance.
CONTENTS
Dear Omega Customers __________________________________ 1
General description and parts names ______________________ 2
Specic terms for parts ___________________________________ 3
Precautions for safe use __________________________________ 4
Warnings and cautions ___________________________________ 5
Slow Juicer assembly ____________________________________ 8
Slow Juicer assembly in detail _____________________________ 9
How to use the appliance _________________________________ 10
Juice Cap and Extraction Packing _________________________ 11
When the Screw is stopped during operation ________________ 12
(How to use [Reverse/REV] button)
Important safeguards in use ______________________________ 13
Disassembly, cleaning and care ___________________________ 14
Bowl disassembly and wash ______________________________ 16
Sterilization and Easy Cleaning System _____________________ 17
Spinning Brush disassembly and wash _____________________ 18
Spinning Brush assembly _________________________________ 19
Bowl Packing assembly __________________________________ 20
Juice Cap Packing assembly______________________________ 21
Troubleshooting _________________________________________ 22
Appliance specications__________________________________ 23
With the Omega Slow Squeezing System and Juice Cap mixing
feauture, you can easily make personalized juice rich in taste,
flavor and full of valuable nutrients.
1. More Nutrients and Taste: Your own personalized juice
Mixed juice
Enjoy single ingredient juice or mixed juice.
Add various ingredients to your taste and health.
Alternative Meal
Make juice as an alternative meal, rich in taste
and balanced nutrients.
Baby Food
Make baby food by mixing meat, grain and vegetables for
various growth phases.
Soybean milk and soy juice
While the juice cap is closed, adjust the proportion of boiled
beans and water to easily make soybean milk and soy juice
to your desired consistency and concentration.
2. More Convenient and User Friendly
Open and close the none drip juice cap to adjust the amount
of juice desired.
3. More Advanced Easy Cleaning System (Page 17)
The juice cap makes clean-up easy! Fill the bowl with water
and operate the appliance for easy washing.
1
SPECIFIC TERMS FOR PARTSGENERAL DESCRIPTION AND PARTS NAMES
<FRONT><BACK>
HOPPER
SQUEEZING SCREW
COARSE STRAINER
(OPTIONAL)
FINE STRAINER
SPINNING BRUSH
BOWL
PULP CONTAINER
JUICE CONTAINER
CLEANING BRUSH
SMALL CLEANING BRUSH
1. Hopper front
triangle
2. Bowl triangle
3. Pulp outlet
STRAINER*
4. Hopper
rear part
5. Operating
switch
6. Juice outlet
7. Juice cap
8. Power cord
9. Grip
COARSE STRAINER (Optional)
The bigger holes in the strainer produce thicker juice when tender and soft fruits are extracted such as
strawberries, kiwis and tomatoes.
FINE STRAINER
The holes of the strainer are small. Use it when making pure juice with hard fruits,
WARNING Hazards or unsafe practices which could result in serious personal injury or death.
WARNINGS AND CAUTIONS
WARNING
Hazards or unsafe practices which could result in serious personal injury or death.
SIGN EXAMPLES
CAUTION Hazards or unsafe practices which could result in minor personal injury or appliance damage.
The sign indicates contents that may cause risk of a fire or an electrical shock.
Specific warnings are written in the sign.
The sign indicates contents that may cause risk of a fire or an electrical shock.
Specific warning are written in the sign.
The sign indicates prohibited acts.
Specific prohibitions are written around or in the sign.
The sign indicates contents of regulating or directing actions.
Specific intructions are written around or in the sign.
DO NOT PLUG IN OR UNPLUG WITH WET HANDS.
It may cause an electric shock or an injury.
DO NOT USE WITH OTHER THAN RATED VOLTAGE.
It may cause an electric shock, a fire or abnormal performance.
It the voltage is diffirent, it may shorten the life of the motor or cause a failure.
PLUG THE POWER CORD CORRECTLY AND PUSH IT TIGHT IN A WALL SOCKET.
It may cause an electric shock or a fire.
IF THE SUPPLY CORD IS DAMAGED, IT MUST BE REPLACED BY THE
MANUFACTURER, ITS SERVICE OR SIMILARLY QUALIFIED PERSONS
IN ORDER TO AVOID A HAZARD.
If the power cord is damaged, it may cause an electric shock or fire.
NEVER ALTER THE APPLIANCE. ALSO, DO NOT DISASSEMBLE OR REPAIR BY
YOURSELF. DO NOT INSERT FINGERS, FOREIGN SUBSTANCES OR OBJECTS
SUCH AS PINS INTO GAPS OR HOLES IN THE BASE.
It may cause a fire, an electric shock or a failure.
For any technical support, contact the authotized local Customer Care Center.
DO NOT MOISTEN THE BASE OR SPLASH WATER ON THE BASE.
Be careful not to let any liquids or other substances get into the switch on the appliance.
DO NOT OPERATE THE SWITCH WITH WET HANDS.
It may cause an electric shock or fire.
WHEN THE POWER CORD, WIRE IS BROKEN OR DAMAGED OR THE PLUG-IN
PART BECOMES LOOSE, DO NOT OPERATE IT.
It may cause an electric shock, a fire or an injury.
FOR SAFETY, MUST DO GROUND CONNECTION. DO NOT DO THE
GROUNDING ON GAS PIPE, PLASTIC WATER PIPE, TELEPHONE WIRE, ETC.
It could cause an electric shock, a fire, a malfunction and an explosion.
Be sure to use the socket with ground connection.
45
WARNINGS AND CAUTIONSWARNINGS AND CAUTIONS
NEVER DISASSEMBLE BOWL SET DURING OPERATION OR
INSERT FINGERS, FOREIGN OBJECTS SUCH AS FORKS, SPOONS ETC.
INTO FEEDING TUBE OR JUICE OUTLET.
It may cause an injury, an accident or a failure.
THIS APPLIANCE IS NOT INTENDED FOR USE BY PERSONS (INCLUDING
CHILDREN) WITH REDUCED PHYSICAL, SENSORY OR MENTAL CAPABILITIES,
OR LACK OF EXPERIENCE AND KNOWLEDGE, UNLESS THEY HAVE BEEN GIVEN
SUPERVISION OR INSTRUCTION CONCERNING USE OF THE APPLIANCE BY
A PERSON RESPONSIBLE FOR THEIR SAFETY.
Children should be supervised to ensure that they do not play with the appliance.
CAUTION
Hazards or unsafe practices which could result in minor personal injury or
appliance damage.
DO NOT OPERATE WITHOUT LOCKING THE HOPPER PROPERLY.
It may cause an injury or a failure.
WHEN DETECTING A GAS LEAK, DO NOT INSERT THE POWER CORD INTO ITS
SLOT. OPEN THE WINDOW TO VENTILATE FULLY AND IMMEDIATELY.
It may cause an injury or a failure.
NEVER PUT A FINGER, A FORK OR A SPOON ETC. INTO JUICE OUTLET.
It may cause an injury or a failure.
IF SCREW ROTATION IS STOPPED IN NORMAL OPERATION, PRESS [REVERSE/REV]
BUTTON AND HOLD FOR 2~3 SECONDS AND THEN AFTER REVERSE OPERATION
IS COMPLETELY STOPPED, PRESS [ON] BUTTON AGAIN.
If such a stop event continues duringthe operation, the parts may be damaged and
performance may be deteriorated due to overheating in a motor. When the problem
continues, immediatly stop the appliance and contact the local Customer Care Center.
WHEN USING THE APPLIANCE, BE CAREFUL FOR A NECKTIE, LONG NECKLACE,
SCARF ETC. NOT TO BE ENTANGLED INTO FEEDING TUBE.
It may cause an injury, a failure or a breakage.
PLACE THE APPLIANCE ON A FLAT AND STABLE SURFACE.
It may cause an injury or a failure.
DO NOT OPERATE THE APPLIANCE FOR MORE THAN 30 MINUTES AT A TIME.
It may cause a motor failure due to overheating.
Cool it down sufficiently for 5 minutes and operate it again.
WHEN PLACING INGREDIENTS INTO THE FEEDING TUBE, ONLY USE THE
PUSHER PROVIDED.
It may cause an injury or a failure.
DO NOT ALLOW A SEVERE SHOCK TO THE APPLIANCE OR DROP IT.
It may cause an electric shock, a fire or damage.
IF THE APPLIANCE GIVES OFF AN UNPLEASANT SMELL OR EXCESSIVE
HEATING, SMOKE, STOP USING IMMEDIATELY AND CONTACT THE LOCAL
CUSTOMER CARE CENTER.
When using a new appliance, it gives off a smell and the smell disapears naturally over time.
ALWAYS UNPLUG THE APPLIANCE AFTER USE.
WHEN UNPLUGGING THE POWER CORD, MAKE SURE TO HOLD THE POWER CORD.
If holding the wire to unplug, it may cause an electric shock or a fire.
DO NOT WASH AT HIGH TEMPERATURES OF 800C (1760F) OR MORE.
DO NOT PUT THE APPLIANCE IN A DISHWASHER, A DRYER OR A MICROWAVE ETC.
It may cause a failure or parts deformation.
DURING THE OPERATION, DO NOT ATTEMPT TO MOVE THE BASE,
DISASSEMBLE THE BOWL SET OR PARTS AND TRY TO LOCK THEM.
It may cause an injury or a failure.
Any act of event needed, switch off first and unplug the power cord.
67
THE APPLIANCE WEIGHS ABOUT 6KG (13.2LB).
WHEN MOVING THE APPLIANCE, ENSURE TO MOVE IT HOLDING GRIPS TIGHTLY
AT THE BASE BOTTOM WITH BOTH HANDS.
If attempting to hold bowl or the edge of the base, the base falls causing an injury
or a failure.
SLOW JUICER ASSEMBLYSLOW JUICER ASSEMBLY IN DETAIL
Align the hopper rear part with base completely as in below.
4
The hopper will not close properly when the parts are not assembled correctly.
Align hopper front triangle with [ ] bowl triangle
OPEN ] first and turn it to clockwise until it
[
clicks so that the hopper triangle [
with bowl triangle [Close
Make sure to press the screw down into the
strainer as in STEP 2. The hopper does not close
properly when the screw does not fit in completely.
] aligned
].
Assemble the parts in the order of bowl > spinning brush > strainer > squeezing screw > hopper
2,3
(or assemble the spinning brush into the bowl then fit strainer bump in the bowl inner groove).
Make sure all the triangles of bowl [ OPEN ], strainer [ ] and hopper [ ] are aligned in a vertical line.
Hopper
Squeezing Screw
Hopper
rear part
Strainer
bump
BOTTOM
OF THE
STRAINER
Assemble the parts as following order :
Bowl > Spinning Brush > Strainer. Make sure bowl
triangle [
Place the bowl in the base.
OPEN ] aligns with strainer triangle [ ].
A spinning brush can be assembled regardless
of the direction.
Strainer
Spinning brush
Bowl
Insert extraction packing at the bottom of the bowl hard enough into the pulp outlet.
1
Make sure bowl outer groove aligns with base bump completely
Open
Extraction
packing
Bowl inner
groove
Base bump
Bowl outer groove
INSIDE THE
BOWL
89
HOW TO USE THE APPLIANCEJUICE CAP AND EXTRACTION PACKING
BACK VIEW
OPERATING
SWITCHES
Normal
direction
Normal
direction
Press
Wash the fruits and/or vegetables and cut
them in to pieces that fit in to the feeding
tube. Place the suitable pieces into feeding
tube slowly and press with a pusher.
Use fresh fruits and vegetables for juicing
as they contain more juice.
OPERATING
SWITCHES
Normal
direction
off (stop)
Normal
direction
Stop
STOP status
JUICE CAP
This is the cap of juice outlet in the bowl.
Close the juice cap and fill up with juice in the bowl with various ingredients. You can easily make mixed juices.
Juice cap
Juice cap
Juice cap
packing
Close juice cap and press [ON] button to start.
When juice starts filling up the bowl, you can
mix banana, nuts, boiled sweet potato etc.
and liquids such as milk etc. as well as vegetables
and fruits like smoothies.
Open juice cap to pour out as much juice as you want.
Close juice cap without any drops.
EXTRACTION PACKING
This is the pulp stopper made of silicone at the bottom of the bowl. Make sure to close extraction packing always as shown below
before use. For cleaning, let extraction packing open and start washing. (Page 16)
Reverse
Reverse
direction
direction
Press [ On ] button to start.
Reverse
direction
Reverse
direction
After juicing is completed, click
[ Reverse/ REV ] to stop.
Motor does not stop immediately when
clicking [ Reverse/REV ]. It stops slowly for
safety and performance reasons.
Extraction
packing
CLOSED
1011
WHEN THE SCREW IS STOPPED DURING OPERATION
(REVERSE/REV BUTTON)
Click [ Reverse/REV ] button and stop
the appliance.
Stop
Press [ Reverse/REV ] button in operating
switches for 3~5 seconds and release it.
Repeat this process 2~3 times.
Reverse is the button pushing ingredients
upward. Reverse only works while the button
is pressed and held. Once button is released,
screw rotation stops.
Reverse
direction
(REV)
After the rotation stops completely,
Normal
direction
(ON)
press [ON] button to operate.
Any direction you want to change from either
Normal direction or Reverse direction, make
sure that screw rotation is stopped completely.
Then operate any button you needs.
IMPORTANT SAFEGUARDS IN USE
• Fruits with pits, hard seeds such as nectarines, peaches, mangos, apricots,
plums and cherries must be pitted before juicing.
• Cut brous ingredients (water parsley setc.) in small size like 3~4cm (1.5inch)
and place to the feeding tube
• Drink the fruit juice or green vegetable juice immediately after you have extracted.
If it is exposed to air for a period of time, the juice will lose its taste and natural value.
• Do not use the appliance for grinding dry ingredients such as grains, coffee beans, etc.
It may cause a part damage or a failure.
• Do not re-squeeze the pulp in the pulp outlet.
• Do not operate the appliance when the bowl is empty.
DO NOT USE IT FOR MORE THAN 30 MINUTES CONTINUOUSLY.
It may cause a failure due to overheating in a motor.
When using continuously, stop and cool it down for 5 minutes in between each
30 minute use.
NEVER INSERT A FINGER, A FORK OR A SPOON, ETC. INTO JUICE OUTLET
DURING OPERATION.
It may cause damage to parts.
ONLY USE THE PUSHER TO PRESS DOWN THE INGREDIENTS.
If using other object, it may cause damage to parts, an injury or a failure.
DO NOT PLACE GRAINS, FRUIT WITH HARD SEED OR NUTS WITH HARD
SHELL SUCH AS WALNUTS.
It may cause damage or a failure of bowl, screw, squeezing strainer, etc.
Fruits with pits,hard seeds such as nectarines, peaches,mangos, apricots, plums and
cherries must be pitted before.
DO NOT OPERATE SWITCHES WITH WET HANDS.
It may cause an electric shock, an electric leakage or a fire.
Do not leave any foreign substances around switches.
DO NOT JUICE SEAFOOD AND MEAT.
NOTE
If the screw does not work even after the above
process, unplug the power cord from the socket,
disassemble the bowl set, wash and use it again
It may cause abnormal performances or a failure.
DO NOT JUICE FRUIT PRESERVED IN SUGAR, HONEY, ALCOHOL, ETC .
(GRAPES, APRICOT, BERRIES, ETC.).
NOTE
Frozen fruit or withered ingredients stored in the refrigerator for a long time may produce less juice
or no juice at all.
1213
DISASSEMBLY, CLEANING AND CAREDISASSEMBLY, CLEANING AND CARE
FIGURE IN ORDER
1. Ensure the motor stops completely and unplug the power cord.
When unplugging the power cord, hold the head part of the power cord and unplug it.
Do not touch the power cord with wet hands.
2. Hold the juice outlet and the hopper with both hands and lift them up from the base.
3. Disassemble the parts as below:
1) Unlock the bowl twisting to counterclockwise.
Juice outlet
2) Take the screw out.
3) Remove the strainer.
4) Take the spinning brush out and disassemble the silicone brush.
4. Rinse each parts with cleaning brush. Brush the inside and outside under running water.
Never use scouring pads, abrasive cleaning agent aggressive liquids or sharp cleaning tools.
Do not wash them in a dishwasher or a dish dryer.
5. Wipe the stain on the base with soft damp cloth or wrung towel and dry the base thoroughly.
Do not immerse the base unit in water or any other liquid nor rinse, it under tap.
6. After each cleaning ,allow parts to air-dry completely and store in a clean and safe place.
Always wash the bowl set immediately after each use. If you skip this step, pulp may dry up and stick to the bowl set.
making it difficult to disassemble or wash. It may also cause degradation in performance.
1415
BOWL DISASSEMBLY AND WASHSTERILIZATION AND EASY CLEANING SYSTEM
Juice cap
packing
bowl packing
Remove Juice Cap packing and bowl packing.
1
Open juice cap first. Hold the bowl and juice cap with one hand and remove juice cap packing with the other hand.
When removing it, be careful not to drop the juice cap and bowl. It may cause damage to the juice cap.
Remove the bowl packing by pinching and twisting it with two fingers.
Extraction
packing
STERILIZATION
For sterilization, use baking soda or natural wash-up liquids only.
You can thoroughly wash parts by immersing in water diluted with one or two drops of baking soda
or natural wash-up liquids for about 30 minutes.
EASY CLEANING SYSTEM
Open
Open the extraction packing at
the bottom of the bowl
2
1617
Wash the bowl and all the packings.
3
Wash bowl and bowl packing with cleaning
brush under the running water.
After closing the juice cap, pour the water
into feeding tube and operate the appliance.
1
Whenever changing the ingredient, it is not necessary to disassemble and wash the bowl.
After juicing, make sure to disassemble and wash the bowl set.
After a while, open the juice cap
and discharge the water.
2
SPINNING BRUSH DISASSEMBLY AND WASHSPINNING BRUSH ASSEMBLY
Spinning brushSilicone brush
Cleaning brush
Remove the spinning brush
from strainer.
Detach the silicone brush from
spinning brush.
As shown to the left, hold the outer part of
silicone brush with your fingers an pull it out
to the arrow direction. It is recommended
to remove it according to the above method.
If pulling it by force, silicone brush may be
torn or spinning brush may be damaged.
With cleaning brush, wash inside and
outside of spinning brush like brushing
under the running water.
Wash silicone brush in the same way under
the running water.
SPINNING BRUSHSILICONE BRUSH
Brush
groove
Inner
wing
Down
(shorter part)
UP
(longer part)
Outer wing
Check the groove of the spinning brush
and the direction of silicone brush.
There are grooves to insert silicone brush in
the spinning brush.
Silicone brush has inner wing
and outer wing.
As shown to the left, let ‘inner wing’ face
the spinning brush.
Insert the silicone brush into
the spinning brush.
According to the N o.1 above, let the longer
part of inner wing
Hold the outer wing of silicone brush
with your thumb and index finger and
insert the inner wing into the groove
of spinning brush.
face upward.
Pull the inner wing tight enough.
Push silicone brush from the outer side
of spinning brush and pull ‘inner wing’ in
the direction of inside of the spinning brush
with the other hand as shown to the left.
Hold the outer wing of silicone brush
Pull it until you cannot pull it any longer.
If units are operating without fully assembled,
there is a risk of breakage.
Hold up and down of ‘outer wing’ and pull
it tight enough.
1819
BOWL PACKING ASSEMBLYJUICE CAP PACKING ASSEMBLY
Bowl
packing
Hold the bowl packing like pinching.
As shown to the left in a dotted circle,
let the protrusion part on the bowl packing
face upward and hold it like pinching with
your thumb and index finger.
Insert the bowl packing into the
bowl hole.
Insert the bottom of the bowl packing
into the bowl hole and fully press it down.
Do not insert whole part of bowl packing.
The upper part of the bowl packing must
be shown.
Turn over the bowl and organize the
bowl packing in place.
If the bowl packing at the bottom of the bowl
is not fully inserted and bent, organize it with
the rotating attractor of the cleaning brush.
Hold juice cap packing as shown
to the left.
As shown to the left in a dotted circle,
the hole must be visible when you hold.
Juice cap packing
Open the juice cap and insert the juice
cap packing in.
Insert it in from the top to the juice cap.
Be careful not to drop the bowl.
Organize the packing to seal
off completely.
If the packing is not completely sealed,
it may cause juice leaking.
2021
TROUBLESHOOTINGAPPLIANCE SPECIFICATIONS
Check the details below before contacting Technical Support for repair or service.
If you need information or if you have a problem, please contact the local Customer Care Center.
When applying for after sales service, check the manufacturer’s serial number or bar code.
THE APPLIANCE DOES NOT WORK.
Make sure the power cord is properly plugged in.
Check the hopper is assembled properly. If the hopper has not been properly locked in place, the appliance does not work for safety reasons.
Check if the appliance has been assembled according to the manual in an ordinary manner.
See the assembly in the manual or consult with the local Customer Care Center for help.
THE HOPPER DOES NOT OPEN.
Is there alot of pulp left inside the bowl? Press [ ON ] button to discharge internal pulp.
Have you placed any foreign substances or solid objects such as hard seeds?
Press the [ Reverse/REV ] button to make foreign substances come up again toward the feeding tube.
Do not attempt to open it by force or with too much pressure. Still it does not work following by the above process,
contact the local Customer Care Center.
IT STOPS DURING NORMAL OPERATION.
Have you put heavy loads of ingredient or a thick/big ingredient? Read the manual Page 12 and follow Reverse/REV button guideline
Still the problem has not been solved, contact the local Customer Care Center.
APPLIANCE STANDARDS
PRODUCT NAME Omega Slow Squeeze Juicer
MODEL NAME VR T400 Series
RATED VOLTAGE 120 V
RATED FREQUENCY 60 Hz
RATED POWER
CONSUMPTION 150 W
RPM (REVOLUTIONS
PER MINUTE) 80 RPM
THERE ARE GATE MARKS (FORMING MARK) RESULTING FROM THE MOLDING PROCESS.
It is normal, and there is no problem for use.
WHAT IS THE DIFFERENCE BETWEEN FINE STRAINER AND COARSE STRAINER?
Regarding strainer selection for suitable ingredients, read the manual Page 3.
JUICE LEAKS OVER THE BASE.
Is Extraction packing properly inserted in?
Juice could leak when the extraction packing is not properly inserted. Please push the extraction packing tight enough.
Juice is still leaking even though the extraction packing was inserted properly?
If an amount of input ingredient is too much compared to the size of pulp outlet, the packing may be slightly pushed out and
juice may leak through the gap. Do not process heavy loads at a time; squeeze little by little.
THE BOWL SHAKES WHEN SQUEEZING.
Slight shaking may be occurred due to motor movement.
Large or small movements occur depending on the pulp texture of ingredients (hard or tough).
It is normal when the screw is rotating. Please note that it is not malfunction.
Hard ingredients (e.g:carrots/potatoes/radishes/beetroots etc.) may shake the bowl more than soft and juicy ingredient.
CORD LENGTH 1.4 m
MOTOR Single-phase
induction motor
FUSE 250 V 10 A
OUT WARD Width 160 MM
DIMENSIONS Length 218 mm
Height 405 mm
RATED
OPERATING TIME LESS THAN 30 MINUTES
2223
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.