Omega M1000 User Manual

INSTRUCTION

MANUAL

Eat well, drink well and live well with Omega www.omegajuicers.com

Drink Mixers

M1000/M3000 SERIES

Product Contents

English, January 2014

PLEASE READ THESE INSTRUCTIONS CAREFULLY BEFORE USE

Contents

Important Safeguards _______________________________________ 2
Specifications ______________________________________________ 3
Parts and Features __________________________________________ 4
Operating & Cleaning Procedures ____________________________ 5-8
Wall Mounting __________________________________________ 9-10
M1000/M1220 Exploded View ________________________________ 11
M1000/M1220 Parts List ____________________________________ 12
M3000/M3220 Exploded View ________________________________ 13
M3000/M3220 Parts List ____________________________________ 14

IMPoRtAnt sAFeGUARDs

We have provided many important safety messages in this manual and on
your appliance. Always read and obey all safety messages.

WARNING – When using electrical appliances, basic safety precautions
should be followed to reduce the risk of personal injury, including the
following:

• Read all instructions before
using mixer.

• Plug into a grounded 3 prong outlet.

• Do not remove ground plug.

• Do not use an adapter.

• Do not use an extension cord.

• Disconnect power before cleaning

or servicing, and before installing
or removing agitator.

• Do not spray or submerge mixer.

• Always use metal container

when mixing.

sAVe tHese InstRUCtIons

• Do not put spoon or other utensils

in metal container when mixing.

• Do not allow agitator to hit

container sides when mixing.

• Inspect mixer and agitator daily.

• Replace agitators every 90 days.

• Do not operate any appliance with

a damaged cord or plug, or after
the appliance malfunctions or is
damaged in any manner.

2

sPeCIFICAtIons

M1000

Rated voltage: AC 120V 50/60HZ
Rated power: 162W
Cord length: 5 foot
Gross weight: 16.53 lb
Box size: 9.06”x9.06”x22.05”

M1220

Rated voltage: AC 220V 50/60HZ
Rated power: 162W
Cord length: 5 foot
Gross weight: 16.53 lb
Box size: 9.06”x9.06”x22.05”

M3000

Rated voltage: AC 120V 50/60HZ
Rated power: 485W
Cord length: 5 foot
Gross weight: 36.6 lb
Box size:

13.5”x11.2”x23.8”

M3220

Rated voltage: AC 220V 50/60HZ
Rated power: 485W
Cord length: 5 foot
Gross weight: 36.6 lb
Box size:

13.5”x11.2”x23.8”

3

PARts AnD FeAtURes

t

The parts and features of your mixer are shown on this page.
Become familiar with all the parts and features before using the mixer.

M3000/ M3220 M1000/ M1220

TOP VIEW OF CONTROLS TOP VIEW OF CONTROLS

Pulse Switch

3-Speed
selector
switch

Pulseswitch

Topcover

2-Speed
selector
switch

Containerguide

Mixing spindle

Agitator

Containerrest

Housing
plug

Agitator

Housing

Containerguide

mega

O

Mixing spindle

Container
guide pin
(ON/OFFactuator)

Container
guide

Agitator

Containerres

4

oPeRAtInG AnD CLeAnInG PRoCeDURe

Operating procedure

Connection to main power supply.

• The electrical safety of this drink mixing machine can only be achieved if

the machine is properly connected to an appropriate grounded
receptacle that is in compliance with current national safety standards.
Therefore, the manufacturer cannot be held responsible for damage and/or
injury caused by failure to connect the unit to an appropriate power source.

• For a safe and correct installation, connect the unit to a dedicated outlet.

• Do not alter the cord or plug in any way.

• The entire length of the power supply cord must not, in any way, be

compressed (bent or bunched together) nor may extension cords be used.

WARNING: THIS UNIT MUST BE PROPERLY ELECTRICALLY GROUNDED
TO AVOID POSSIBLE FATAL ELECTRICAL SHOCK OR SERIOUS INJURY TO
THE OPERATOR. THE POWER CORD IS PROVIDED WITH A THREE PRONG
GROUNDED PLUG. IF A THREE-HOLE GROUNDED ELECTRICAL OUTLET
IS NOT AVAILABLE, USE AN APPROVED METHOD TO GROUND THE UNIT.
DO NOT USE EXTENSION CORDS WITH THIS UNIT. DO NOT “GANG”
TOGETHER WITH OTHER ELECTRICAL DEVICES ON THE SAME OUTLET.

FIGURE A FIGURE B

5

oPeRAtInG AnD CLeAnInG PRoCeDURe

Mixing a drink

• Plug the drink mixer into a grounded outlet.

• Place the ingredients into the container supplied. The basic milkshake

recipe is:
3 No. 24 scoops of ice cream.
4 ounces of very cold milk.
1-1/2 ounces of syrup.

M1000

• Select the required speed using the 2-speed selector switch.

• Position the container in the container guide and move the container

upwards to activate the mixer. Set the container down onto the upper
level of the container rest.

• When the drink is completely mixed, lift the container up off the

container rest and pull down from the container guide. The mixer will
now turn off. The container can now be removed or left in the lower
container guide position.

• Please note that the mixer will not operate without the container being in

the upper position on the container rest.

M3000

• Select the desired speed using the 3-speed selector switch. Switch the

toggle switch to the ON position.

• Position the container in the container guide and move the container

upwards to activate the mixer. Set the container down onto the upper

part of the container rest. If the pulse operation is required, use the

toggle switch to perform this function.

• When the drink is completely mixed, lift the container up off the

container rest and pull down from the container guide. The unit will now
turn off. The container can now be removed or left in the lower container
guide position.

• Please note that the mixer will not operate without the container being in

the upper position on the container rest.

oPeRAtInG AnD CLeAnInG PRoCeDURe

NOTE: Inspect agitator(s) daily and replace every 90 days.

WARNING

Cut Hazard

Always use the metal container when mixing.
Do not put spoon or other utensils in metal container when mixing.
Failure to follow these instructions can result in cuts.

Using the container rest

• To turn the unit off, rest the container on the lower or standby container

rest position.

Replacing the agitator

The drink mixer ships with a solid agitator installed on each shaft.

• Unplug the mixer.

• If the shaft is to be removed, normally a quick turn

counter clockwise will loosen the shaft. If not, remove
the top cover and use a flat head screwdriver inserted
into the top of the motor shaft to prevent the motor
from turning.

• To remove the agitator, loosen the bolt by turning it

counter clockwise with a 5/16” wrench.

• To install the new agitator, turn the bolt into the shaft

and tighten.

To prevent damage to the agitator, do not use pliers to
grip the agitator blades while tightening or loosening.

7 8

oPeRAtInG AnD CLeAnInG PRoCeDURe

Press

Removing/installing the container guide pin & housing plug

• Unplug the drink mixer.

• Hold the container guide by the indents on each side and pull straight down.

• Press the retainer clip and slide the guide pin out of the guide.

• Reverse the above steps to reinstall making note of the correct orientation.

Care and cleaning

• Place a drop of detergent and 1 cup of water into the container.

• Position the container into the container guide and mix on low speed for

5 seconds.

• Empty and rell with clean water and repeat for 5 seconds to rinse.

• Remove the container guide and wash with hot soapy water, then rinse.

• Clean the housing with a damp soapy cloth.

NOTE: Do not spray or submerge the mixer. Resulting water damage will not
be covered under warranty.

WALL MoUntInG

Step:

1. Remove M4X12 screws on back of the machine.

2. Separate main housing and base.

3. Remove two black magnet covers.

4. Fixed the main housing on the wall by using the four screws and

wall anchors supplied.

5. Assemble two black magnet covers.

2

1

9

WALL MoUntInG

3

4

M1000/M1220 eXPLoDeD VIeW

1

2

3

6

7

8

33

10

3

3

16

49

41

50

32

51

24

25

29

30

26

28

27

9

11

12

13

14

15

38

34

35

36

55

4

5

18

17

19

21

21

22

20

21B

23

56

11

37

47

48

No. Part # Description Qty

1 PM1-SWITCH Power Switch 1

Retainer spring 2

2 PM1-2B Top Cover Black 1
3 PM1-3 Screw#1 6
4 PM1-4 Screw#2 2
5 PM1-5C Front Cover Chrome 1
6 PM1-MOTOR-120 Motor 1/2HP 120V 1
PM1-MOTOR-240 Motor 1/2HP 240V 50/60HZ 1
7 PM1-3 Screw#1 3
8 PM1-8 Spring Washer 1
9 PM1-9 Lower motor pad 1
10 PM1-10B Back Panel black 1
11 PM1-11B Upper housing Black 1
12 PM1-12 Magnet 4
13 PM1-13B Magnet cover black 2
14 PM1-14 Upper cup holder 1
15 PM1-15 Microswitch activator 1
16 PM1-16 Lower cup holder 1
17 PM1-SHAFT Stir Shaft with parts 18,19,22 1
20 PM1-20 Agitator standard with locking bolt 1
21 PM1-21 Agitator hinged 1
21B PM1-21B Agitator high power 1
22 PM1-22 Screw#3 1
23 PM1-CUP Cup 1
PM1-CUP-O Cup with lazer engraved Omega 1
24 PM1-24 Switch ejector 1
25 PM1-25 Screw#4 4
26 PM1-26 Spring 1
27 PM1-27 Screw#5 2
28 PM1-28 Screw#6 2
29 PM1-29 Microswitch 1
30 PM1-30 Microswitch bracket 1
32 PM1-32 Inside cover 1
33 PM1-33 Upper motor supports 3
34 PM1-34B Lower housing 1
35 PM1-35 Base support 1
36 PM1-36 Bottom cover 1
37 PM1-37 Feet 4
38 PM1-38 Screw#7 2
41 PM1-41 Screw#8 1
47 PM1-47 Screw#9 4
48 PM1-48 Washer 4
49 PM1-25 Screw#4 5
50 PM1-50 Upper cup holder retainer 1
51 PM1-51
56 PM1-56 Drip tray 1

One (1) Year Parts and Labor

12

M3000/M3220 eXPLoDeD VIeW

13

No. Part # Description Qty

1 PM3-SWITCHT Toggle switch 3
2 PM3-2 Screw#10 2
3 PM3-3 Screw#11 1
4 PM3-4C Top cover 1
5 PM3-SWITCHR Rocker switch 3
6 PM3-6 Upper motor support 1
7 PM3-MOTOR-120 Motor 1/2HP 120V 3
PM3-MOTOR-240 Motor 1/2HP 240V 50/60HZ 3
8 PM3-8 Spring Washer 4
9 PM1-9 Lower motor support 3
16 PM1-16 Lower cup holder 3
17 PM1-SHAFT Stir Shaft with parts 18,19,22 3
20 PM1-20 Agitator standard with locking bolt 3
21 PM1-21 Agitator hinged 3
21B PM1-21B Agitator high power 3
22 PM1-22 Screw#3 3
23 PM1-CUP Cup s/steel 3
0 PM1-CUP-O Cup s/steel with lazer engraved Omega 3
25 PM1-25 Screw#4 4
26 PM1-26 Spring 1
27 PM1-27 Screw#5 2
28 PM1-28 Screw#6 3
29 PM1-29 Microswitch 3
30 PM1-30 Microswitch bracket 1
37 PM3-37 Washer 4
38 PM3-38C Front cover 1
40 PM3-40B Housing complete 1
41 PM1-41 Screw#8 3
42 PM3-42 Foot rear 2
43 PM3-43 Front suction cup 2
44 PM3-44 Foot Front 2
45 PM3-45 Screw#12 1
46 PM3-46 Drip tray 1
47 PM3-3 Screw#11 4
49 PM1-25 Screw#4 5
50 PM1-50 Upper cup holder retainer 1
51 PM1-51 Retainer Spring 1
52 PM3-52 Power cord cover 1
53 PM3-53B Back cover 1
54 PM1-22 Screw#3 3
57 PM1-25 Screw#4 9
58 PM3-58 Upper cup holder 3
59 PM3-59 Microswitch activator 3
60 PM1-24 Switch ejector 3

One (1) Year Parts and Labor

14

OMEGA PRODUCTS, INC.

6291 LYSTER LANE

HARRISBURG, PA 17111-4523 U.S.A.

PHONE: [phone]

FAX: [phone]