BL600 SERIES BLENDER
BL330 SERIES
BLENDER
BLENDER SAFETY
DANGER Electricity
DANGER Risk of Electrical Schock
WARNING
Electrical Shock Hazard
Plug into a grounded outlet.
Do not remove ground.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can
result in death, fire or electrical shock.
FAILURE TO ADHERE TO THESE WARNINGS CAN RESULT IN FIRE,
SERIOUS INJURY, ELECTRICAL SCHOCK AND/OR DEATH
Technical Services
GENERAL Caution
DANGER Keep Hands Clear
WARNING
Moving Parts!
Always cover the lid on the container when
blending.
Do not put hands, spoons or other utensils in
container when blending.
Failure to follow these instructions can result
in broken bones, cuts or other injuries.
For assistance or replacement parts, call
Technical Service
24 Hours a Day, 7 Days a Week at
Toll Free: #1-877-368-2797
IMPORTANT SAFEGUARDS
When using electrical appliances, basic
safety prec autions should a lways be
followed, including the following:
1. Read all the instructions before using the
blender.
2. Plug into a grounded outlet.
3. Do not remove ground.
4. Do not use an adapter.
5. Do not use an extension cord.
6. To protect against risk of electrical shock,
do not put the blender in water or other liquid.
7. Close supervision is necessary when any
appliance is used near children.
8. Unplug from outlet when not in use, before
putting on or taking off parts, and before
cleaning.
9. Avoid contact with moving parts, especially
blades.
10. D o not operate any appliance with a
damaged cord or plug or after the appliance
malfunctions, or is dropped or damaged in
any manner. Return appliance to the nearest
authorized service facility for examination /repair
/elect rical or mechan ical adju stment, or
contact your Omega Distributor.
14. Screw on locking ring firmly. Injury can
result if moving bla des ac cidenta lly be come exposed.
15. Always operate blender with lid in place.
16. When blending hot liquids, place a hand
towel over the cover. Do not fill blender container beyond 2-3 full. Always begin processing at the lowest speed setting. Keep hands,
arms and face away from the feeder cup
opening to prevent possible burns.
17. Do not use outdoors.
18. Do not let cord hang over edge of table
or counter, or touch hot surfaces.
19. Do not leave blender unattended while it
is operating.
2 0 . Th e u s e o f a t ta c h m en t s n o t
a p p ro ved by Omega may cause injuries.
21. The capacity can be substantially less
than normal with thick mixtures.
22. Inspect the container assembly daily. Do
not use a broken, chipped or cr ac ke d
container. Check cutter for wear, nicks or
broken blades.
23. This appliance is int ended for short
period of operation, with a average rated operating time of approximately 3 minutes.
11. Caution: Keep hands and utensils out of
container while blending to reduce the risk of
severe injury to persons or damage to the
blen d e r. If sc r a p ing, fo l d i n g, e tc. is
nec e s sary, turn off and unplug the blender,
and use a rubber spatula only.
12. Warning : Blades ar e sharp. Handle
carefully.
13. To reduce the personal injury, never place
cutting blades on base without jar properly attached.
BLENDER OPERATION
To operate the blender, proceed as follows
1.For the first time user, wash the container assembly, including the lid, before using it. (Refer
to "Cleaning Instruction") Do not put the container assembly & blender base assembly in the
dishwasher.
2.Place the blender on a dry, clean, level surface,
and press OFF.
3.Place the container onto the motor base. Make
sure it rests securely on the base.
4.Plug the blender into an electric outlet.
5.Place the ingredients into the container.
4.Place the lid and feeder cap tightly on the container.
7.Select desired speed and time by rotating dials.
8.Press ON.
PROFESSIONAL BLENDER TIP
1.Processing hot liquid
mAlways cover the lid and feeder cap before blending hot liquid or mixtures.
mUse the feeder cap to add liquids to the
container while the unit is running.
mNever stand with your face directly over the container when you are putting ingredient
through the feeder cap.
2.Blending Icy mixtures
mSteps for blending ice:
Pour in liquid, and then add ice.
Place the lid.
Set to desired speed
Chunks of frozen fruit can be added to milk or fruit juice to
produce a sherbet or slush.
Use the feeder cap to add liquids or ingredients to the container
while the unit is running.
CLEANING INSTRUCTION
Blender container parts are corrosion resistant, sanitary and easily cleaned. Do not
put the container assembly & blender base assembly in the dishwasher.
1.Before first use and after every use, separate container parts from the base.
2.Add cleaning solution to the container. Use washing solution of tepid water (less than
115°F/46°C) and a non-sudsing detergent. Use the recommended amount of detergent.
3.Scrub and flush out the container interior lid and feeder cap to remove food residue. Empty
container.
4.Fill container 1 /4 full with fresh washing solution and place it on the base.
5.Replace the lid on the container and run the blender on high speed for 2 minutes.
6.Repeat step 4 using clean rinse water (95°F/35°C).
7.Wipe down the container, feeder cap, and lid with a soft cloth or sponge, dampened with
fresh washing solution.
8.Wipe the exterior of the base with a damp cloth or sponge. The base contains electrical
components: do not immerse, use a high-pressure washer, or use a dishwasher to clean the
base.
CARING TIPS
To care for your blender, please read the tips as follows:
1.Periodically check all parts before reassembly. As use of damaged or non-recommended
parts could result in a severe personal injury and/or damage to the blender
2.Blades:
If the processing blades are stuck or difficult to turn, DO NOT USE BLENDER (Check by
carefully turning the blades in a counterclockwise direction, where the opposite edges are
sharp. Blades should turn freely.)
3.Container:
If the Ea stman Tri ta n contai ner is cr acked, D O N OT USE BL ENDER, f ur ther use
could result in the container breakage during use.
4.Blender Base:
Never immerse the blender base in water. Unplug unit. The housing can be cleaned with a
damp cloth.
5.Motor:
The motor is permanently lubricated and does not require any additional lubrication.
TROUBLESHOOTING
Problem Solution
1. Place container properly on the base
2. Check to ensure controls are clean
and moving freely.
3. Double-check to ensure power cord is
1. Blender fails to start.
2. Stopped
3. Ingredients do not mix properly
securely plugged into the electric outlet.
4. Check to see if the circuit breaker has
tripped or if the fuse for the electric outlet has blown.
1. Unplug blender and wait 5 minutes.
Plug the blender back in and resume operation.
1. Container is too full.
2. Cutter unit blades are not sharp
enough or are damaged.
3. Solid pieces are bigger than 1"
(25mm) cubes.
4. Check the speed to create a fluid
blend.
5. Check to see if enough liquid has
been added to the ingredients. Mixture
should be fluid and free-running at all
times.
MAINTENANCE
Inspect the blender and its various parts and replace as follows:
1. Unplug the blender and remove the
container from the base.
Daily
Weekly
2. Inspect the container blades for wear,
nicks, and broken or loose blades. Replace if necessary.
1. Unplug the blender.
2. Inspect the power cord insulation and
power plug for cracks. Refer to "Technical Service" for repair or replacement.
1. Review the condition of the container
Quarterly
assembly and Mushroom Clutch Set at
least every 90 days.
1. Replace if necessary.
Replacement Parts
For replacement parts, call toll free: #1-877-368-2797
Warranty
2 Year Parts & 90 Days On-Site Labor
Warranty claims can be made by calling 800-633-3401 during normal business hours between 8:30am and
5:30pm Eastern, Monday thru Friday excluding Weekends and Holidays. Emergency warranty service
claims can be made after hours, weekends and holidays by dialing 800-633-3401 and following the automated prompts.
All claims must include: make, model number, serial number, proof of purchase (dated receipt), month and
year of installation, authorized equipment dealer and all pertinent information supporting the claim prior to
the issuance of a warranty claim number. At the time of a warranty claim, should on-site service be necessary, a service company will be dispatched by The Legacy Companies to the location to facilitate repairs
covering labor, parts (premium or overtime service is not included) and appropriate travel (not to exceed 2
hours or 100 miles round trip).
If during the warranty event the on-site technician determines the issue to be the result of improper installation, misuse, abuse, or requires adjustments and/or calibration, the end user will become responsible for
any charges brought forth by the service company. Should on-site service not be authorized as an option
for your product, an RMA (Return Merchandise Authorization) may be issued. The issuance of an RMA requires the end user provide adequate packaging and shipping including the cost of freight to The Legacy
Companies Service Center for disposition. Should a replacement unit be necessary, it will be at the sole
discretion of TLC Management and a new or refurbished unit will be provided. The cost to repair or replace
the item including the cost to ship the unit back to the end user will be covered as a part of the warranty.
OMEGA BL330 3 2011 Rev A
Loading...