Omega DB-PASS-23A Installation Instructions Manual
GMBP INSTAL LATION COM PATIBILITY CHART
V EHIC L ES 2006 2005 2004 2003 2002 2001 2000 1999 1998
ALE R O
1 1 1 1 1
A URORA
2 2 2 2
AVALANCHE
1 1 1
AZTEK
2* 2* 2* 2*
BONNEV ILLE
2 2 2 2 2
BRAVADA
1 1 1
CA DILLA C CTS
2 2
CA DILLA C STS
2 2 2 2 2 2 2
CA DILLA C DEVILLE
2 2 2 2 2 2 2
CA DILLA C SLS
2 2
SIERRA CK 1500, 2500, 3500
1 1
ENV OY
1 1 1
RA INER
1
GRA ND A M
1 1 1 1 1 1
GRA ND PRIX
3*
3* 3* 3* 3*
HUMMER H2
1
IMPA LA
1 1 1 1
LESABRE
2 2 2 2 2
MONTA NA
2* 2* 2* 2* 2* 2* 3*
MONTE CA RLO
1 1 1 1
PARK AVENUE
2 2 2 2 2 2 2
RENDEZ-V OUS
2* 2* 2*
SUBURB A N
1 1 1 1 1 1 1
SUNFIRE
1 1 1 1 1
CAVALIER
1 1 1 1 1
SILHOUETTE
2* 2* 2* 2* 2* 3*
TRAILBLAZER
1 1 1
TRA NSPORT
2* 2* 2* 2* 3*
V ENTURE
2* 2* 2* 2* 2* 3*
YUKON
1 1 1* 1* 1* 1* 1*
DB-PASS-23A Installation Instructions
GM PASSLOCK II & PASSKEY III INTERFACE MODULE
DB-PASS-23A INSTALLATION
COMPATIBILITY CHART
1 = INSTALL 1
2 = INSTALL 2
3 = INSTALL 3
*DB-PASS-A will not disarm OEM alarm
Programming Jumper:
See FIG. A ,B or C for proper position
CONNECT TO VEHICLE VIOLET DATA WIRE
VIOLET(DATA OUTPUT) (PIN#2 OF OBDII DIAGNOSTIC CONNECTOR)
DB-PASS23A
ORANGE (+)INPUT CONNECT TO ( 12 VOLTS CONSTANT +)
INSTALL 1 PROGRAMMING
Once DB-PASS- 23A harness is correctly connected:
Place programming jumper into PROGRAMMING POSITION
Plug DB-PASS-23A module into harness (Jumper must be in programming position)
Start vehicle with key.
LED on DB-PASS-23A will blink 4 times after engine crank to indicate DB-PASS-23A is
programmed.
Turn ignition key to “OFF” position: then remove jumper from .
Place Jumper into OPERATING POSITION either:
FIG.B: All PASSLOCK 2 or VATS
TECH NOTES:
*DB-PASS-23A IS NOT Compatible with GM Passlock 1
*DB-PASS-23A IS Only Compatible with VATS equipped with OBDII connector 1998+
*OBD1 EQUIPPED VEHICLES DO NOT HAVE A DATA WIRE TO CONNECT TO.
*Pontiac Sunfire, Chevrolet Cavalier, Malibu, Saturn equipped with content theft cannot be disarmed
during remote starting due to internal BCM function. DB-PASS-23A can be used but it is recommended to
add aftermarket keyless entry function and discontinue use of factory remote transmitters to avoid
triggering content theft alarm. Camaro & Firebird have similar content theft systems.
CONNECT TO (-) GROUND OUTPUT WHEN
BROWN (-) INPUT RUNNING WIRE OF REMOTE START SYSTEM
Green N/C
Blue N/C
Violet/White N/C
Pink/White N/C
Pink N/C
Red N/C
Black(-) INPUT CONNECT TO CHASSIS GROUND OF VEHICLE
FIG:A
PROGRAMMING POSITION
INSTALL 1
GM PLASSLOCK 2 (DATA)
PROGRAMMING POSITION
Fig:A
AAB
(LED)
OPERATING POSITION
Fig:B
B
(LED)
Diagnostic plug (front view)
Located under the dash driver side:
below steering column
IMPORTANT: DO NOT CONNECT VIOLET
DATA OUTPUT WIRE OF INTERFACE MODULE
TO VEHICLE DATA WIRE (PIN 2) UNTIL EVERY
OTHER WIRE HAS BEEN CONNECTED & THE
HARNESS HAS BEEN PLUGGED INTO THE
DATA BUS INTERFACE (DL) MODULE.
Fig:C
Fig:D
OPERATION POSITION
For Cavalier & Sunfire
Without Factory Alarm
AAB
(LED)
NOT USE
B
(LED)
DB-PASS-23A Installation Instructions
GM PASSLOCK II & PASSKEY III INTERFACE MODULE
Fig:A
Fig:B
Programming Position
AAB
(LED)
Operating Position
B
(LED)
IMPORTANT: DO NOT CONNECT VIOLET
DATA OUTPUT WIRE OF INTERFACE MODULE
TO VEHICLE DATA WIRE (PIN 2) UNTIL EVERY
OTHER WIRE HAS BEEN CONNECTED & THE
HARNESS HAS BEEN PLUGGED INTO THE
DATA BUS INTERFACE (DL) MODULE.
INSTALL 2
GM PASSKEY3 (Pk3)
N.C
PK3
P
a
s
s
-
Key
I
II
Mod
u
le
REMOTE START
MODULE
INSTALL 2 PROGRAMMING
BROWN - CONNECT TO (-) IGNITION OUTPUT WIRE OF REMOTE START SYSTEM
NO CONNECTIO
VIOLET -
GROUND
BLACK -
ORANGE - +12VOL
TA OUTPU
VIOLET - DA
IGNITION
N
TS CONSTANT
T
BLACK CHASSIS GROUND
RED - N/C
ORANGE - +12 VOLTS CONTANT
PINK - NC
PINK/TRACER - NC
VIOLET - DATA TO ECM
VIOLET/TRACER - N/C
BLUE - N/C
GREEN - N/C
Programming Jumper
CONNECTOR
Programming LED
When the DB-PASS-23A harness is correctly installed:
Place the programming jumper to the “PROGRAMMING” position. (See
Place key in ignition and t
urn to the “ON” position.
FIG:A)
The LED will blink 4 times to confirm sucessful programming.
Turn key to the “OFF” position.
Remove the programming jumper and put it to position -
TECH NOTES: *Vehicles with the ignition cylinder located on the dash: Yellow, Black & White wires can be
found coming from the ring of the cylinder - Trace these wires to the factory PK3 module located just abov
the gas pedal area.
“OPERATING“ (See FIG:B)
GREY
BLACK
ORANGE
VIOLET
PINK
TO ECM SIDE
DBPASS-23-A
PK3
Pa
s
s
-
K
e
y
III
M
od
ule
REMOTE START
MODULE
INSTALL 3
GM PASSKEY3 (Pk3)
GREY - LED
VIOLET - DATA OUTPUT
BLACK - GROUND
ORANGE - +12VOLTS CONSTANT
ORANGE -
FUEL ENABLE LINE
BLUE
PINK - IGNITION
BLACK - CHASSIS GROUND
ORANGE - +12 VOLTS CONTANT
PINK - IGNITION IN
PINK/TRACER - IGNITION OUT
BLUE - FUEL ENABLE LINE
BROWN - CONNECT TO (-) GROUND OUTPUT
WHEN RUNNING WIRE OF REMOTE START SYSTEM
VIOLET - N/C
VIOLET/TRACER - N/C
GREEN - N/C
INSTALL 3:
NOTE: PLACE JUMPER AS SHOWN IN FIG:E BEFORE CONNECTING MODULE.
TO ECM SIDE
GREY
CONNECTOR
RED - N/C
DB-PASS-23A
Fig:E
Programming Jumper
NOT USED
SEE FIG. E
Programming LED
NO PROGRAMMING NECESSARY
JUMPER POSITION
Unscrew cover of DB-PASS-23A unit.
Place jumper as seen below:
Loading...