Omega Crime Guard 350i5 User's Manual

Table Of Contents

Owner’s Guide

Arming the System ....................... 3

Disarming the System ................. 4

Emergency Override .................... 4

System Armed & Activated ........... 5

Panic ............................................ 5

Sensor By-Pass ............................ 5

Auxiliary Channel ......................... 6

3rd Channel .................................. 6

Remote Controlled Anti-Carjack ... 6

Anti-Carjacking ............................. 7

Valet Mode ................................... 8

LED Status Indicator .................... 8

Auxiliary Sensor & Prewarn .......... 9

How To Program Remote Control ............. 9

How To Program Features ...................... 10

Programmable Features .................. 10 - 12

Wiring Diagram ....................................... 13

Door Lock/Unlocking Systems ................ 14

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions, (1) This device may not cause harmful interference and, (2) This device must accept any interference received, including interference that may cause undesired operation. The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user's authority to operate the equipment.

Installation Instructions

Remote Control Quick Reference Guide

Arming: Press & Release the “Lock” button

THE SIREN WILL

CHIRP ONCE

THE DOORS WILL LOCK

(IF CONNECTED)

THE PARKING LIGHTS

WILL FLASH ONCE

Silent Arming: Press & Release the Middle “••” button Twice in 3 sec.

2 X

THE DOORS WILL LOCK

(IF CONNECTED)

THE PARKING LIGHTS

WILL FLASH ONCE

Disarming: Press & Release the “Unlock” button

THE SIREN WILL

CHIRP TWICE

THE DOORS WILL UNLOCK

(IF CONNECTED)

THE PARKING LIGHTS

WILL FLASH TWICE

Silent Disarming: Press & Release the Middle “••” button T wice in 3 sec

THE PARKING LIGHTS

2 X

Page 1

THE DOORS WILL UNLOCK

(IF CONNECTED)

WILL FLASH TWICE

Emergency Override:

THEN WITHIN 10 SECONDS

PRESS & RELEASE

VALET BUTTON

Panic: Press & Hold the “Lock” Button for 3 Sec’s, with the ignition “Off”

THE SIREN WILL SOUND

Hold 3 seconds

THE PARKING LIGHTS

WILL FLASH

Shock Sensor & Prewarn Bypass:

1) Arm the alarm by , Pressing & Releasing the “Lock” button

2) Within 2 seconds Press & Release the Middle “••” button.

Then

To Activate the Auxiliary Channel: Press & Hold The Middle “••”

Button for 3 Seconds

Operate Remote Start Unit

Hold 3 seconds

Operate Window Roll-Up Unit

Open Electric Trunk

To Activate the 3rd Channel: Press & Hold The “•••” Button

for 3 Seconds

Hold 3 seconds Operate Remote Start Unit

Operate Window Roll-Up Unit

To Activate Remote Anti-Carjack: (programmable feature

10)

Press & Hold the “•••” button, for 3 Secs, with the ignition “On”

Hold 3 seconds

Page 2

Arming the Alarm

The system may be "Armed" by any of 3 methods:

1) Remote Control Arming: Press & Release the “Lock” button

THE SIREN WILL

CHIRP ONCE

THE DOORS WILL LOCK

(IF CONNECTED)

THE PARKING LIGHTS

WILL FLASH ONCE

2) SILENT Remote Control Arming: Press & Release the Middle “••”

button T wice within 3 seconds

2 X

THE DOORS WILL LOCK

(IF CONNECTED)

THE PARKING LIGHTS

WILL FLASH ONCE

Upon Arming: • The siren will chirp one time. (3 times if there is open zone)

• The parking lights will flash once.

• The doors will lock. (If an optional interface is connected)

• The starter interrupt will engage.

• The LED St atus Indicator will begin to flash slowly.

- If a zone is open, (for example a car door), when arming, the alarm will still arm, but will bypass the open zone until the zone is secured (siren will chirp 3 times).

3) To Passively Arm: Turn Ignition “Off”, Then Close all Doors.

Automatic “Last Door Arming” is a programmable feature which allows the alarm to arm itself and, if desired, lock the doors upon arming.

If on, anytime the ignition is turned off, and then a door is opened and closed:

• The Siren will chirp once to confirm arming countdown has begun.

• The LED S tatus Indicator will begin to flash rapidly.

Thirty seconds later:

• The siren will chirp & the lights will flash once.

• The LED St atus Indicator will begin to flash slowly.

• The starter interrupt will engage.

- The alarm is now fully armed. The doors will lock at this time, if programmed to do so, and if the vehicle is equipped.

- The system can not Last Door Arm if a protected zone is open. Should a ve- hicle door be opened during the arming countdown, the countdown will stop and start over again when the door is closed. AUTO REARM (programmable) allows the Alarm to Rearm it self, if it is Disarmed and a vehicle door is not opened.

Page 3

Disarming the Alarm

The system may be "Disarmed" by any of 3 methods:

1) Remote Control Disarming: Press & Release the “Unlock” button

THE SIREN WILL

CHIRP TWICE

THE PARKING LIGHTS

WILL FLASH TWICE

THE DOORS WILL UNLOCK

(IF CONNECTED)

2) SILENT Remote Control Disarming: Press & Release the Middle

“••” button Twice within 3 sec

THE PARKING LIGHTS

2 X

THE DOORS WILL UNLOCK

(IF CONNECTED)

Upon Disarm: • The siren will chirp twice. (4 chirps if alarm has activated & reset)

• The parking light s will flash twice. (4 times if alarm has activated)

• The doors will unlock. (If an optional interface is connected)

• The starter interrupt will disengage.

• The LED St atus Indicator begins flashing rapidly for Automatic Rearming, until alarm Rearms or a vehicle door is opened.

2-STAGE DISARM: If Disarming the alarm while it is triggered (siren sounding), the first press of any remote control button will only silence the siren/horn. A second press of the “Unlock” button will Disarm the alarm.

WILL FLASH TWICE

IMMOBILIZER MODE: If this mode is programmed “On”, the starter interrupt will remain engaged after the alarm is Disarmed, until the ignition is turned “On” and you Press & Release the Valet button. (Refer to programmable feature

To Start Vehicle: .

1. Disarm the alarm, then T urn “On” the vehicle’s ignition

2. Press & Release the Valet Button.

Emergency Override

Step 1: With the system in the armed condition, enter the vehicle via the driver's

door (be aware that the alarm will trigger when the door is opened). Step 2: Using your key, turn the vehicle’s ignition to the "On" position. Step 3: Within 10 seconds, Press & Release the Valet/ Override Switch.

THEN WITHIN

10 SECONDS

Page 4

System Armed & Activated

Regardless of method used to Arm the alarm, once Armed, the alarm will monitor all protected zones, and if an intrusion attempt is detected it will activate, or “trigger”.

A trigger consists of the following:

• The electronic siren, or optionally the vehicle’s horn, will start sounding.

• The exterior parking lights will flash on and off repeatedly. An activation has a 30 second duration unless the system is disarmed using the

remote control or the Valet /Override switch. If all protected zones are secure at the end of the trigger, the system will stop and rearm itself to detect further entry attempts. If a protected zone is still open at the end of the trigger cycle, the alarm will continue to re-trigger itself for up to six activated cycles before it resets itself and ignores the violated zone.

Remote Panic Operation

Should it be needed in a threatening situation, or you feel the need to attract attention, the alarm can be triggered using the remote control. Your alarm features “Panic Mode”, which allows you to activate “Panic” from the “Arm/Lock” button.

To Activate Remote Panic: Press & Hold the “Arm/Lock” Button,

for 3 seconds, with the ignition “Off”.

THE SIREN WILL SOUND

Hold 3 seconds

THE PARKING LIGHTS

WILL FLASH

Sensor By-pass

The shock sensor & Prewarn zone can be by-passed using the remote control. This may be useful in stormy weather.

1) Arm the alarm by, Pressing & Releasing the “Lock” button.

2) Within 2 seconds, Press & Release the Middle “••” button.

Then

- The siren will chirp once to confirm sensor has been by-passed.

- Upon Disarming the alarm, the sensor zone will reset.

Page 5

The Auxiliary Channel

The Auxiliary Channel may be used to operate an optional function. Possibilities include remote trunk release, remote car starting, or an on-demand remote window roll-up interface. Please see your Omega dealer for details on available options.

To Activate the Auxiliary Channel: Press & Hold the Middle “••” Button for 3 Seconds.

Opperate Window Roll-

Hold 3 seconds

Opperate Remote Start Unit

Up Unit

Open Electric Trunk

- The alarm will Disarm upon activating the Auxiliary channel.

- The Auxiliary Channel cannot be activated if the vehicle's ignition is "On".

The 3rd Channel Auxiliary Output

The programmable 3rd Channel may be used to operate an optional function, such as a remote start unit or an on-demand remote window roll-up interface. Please see your Omega dealer for details on available options.

To Activate the 3rd Channel: Press & Hold the “•••” button for 3 Seconds.

Opperate Window RollUp Unit

Hold 3 seconds

Opperate Remote Start Unit

- The 3rd Channel can be programmed to Supply a (-) output when the alarm is Armed to operate a Window Roll-Up module (Programmable feature # 12).

Remote Anti-Carjack

The Anti-Carjacking mode can be activated using the remote control.

- Refer to next page for sequence details. (programmable feature

10)

To Activate Remote Anti-Carjack:

Press & Hold The “•••” Button, For 3 Seconds, With The Ignition “On”.

Hold 3 seconds

Page 6

Programmable Anti-Carjacking Protection

The Anti-Carjacking sequence may be activated by any of 3 methods:

1) Using the remote control, by holding down the Small “•••” Button for 3 seconds while the ignition is “On”. (programmable feature # 10)

2) When a door is Opened while the ignition is “On” (programmable feature # 10)

3) Every time the ignition is turned “On”. (Programmable feature # 9)

1) Anti-Carjacking activated using the transmitter: (programmable feature

10)

The Anti Car-Jacking operation may be activated by pressing and holding the remote control’s Small “•••” button for 3 seconds while the ignition is “On”.

2) Anti-Carjacking activated by an Open door: (programmable feature

10)

If programmable feature #10 is “On”, the system will initiate the Anti-Carjacking sequence every time a vehicle door is opened while the ignition is “On”.

3) Anti-Carjacking activated by the ignition: (programmable feature

If programmable feature #9 is “On”, the system will initiate the Anti-Carjacking sequence every time the vehicle’s ignition is turned “On”.

IMMOBILIZER MODE: If the “Immobilizer mode” is programmed “On”, the ignition activated anti-carjacking sequence will be cancelled and the “Immobilizer mode” disarmed by: first turning “On” the vehicle’s ignition, then Pressing &

Releasing the valet button. (Refer to programmable feature

Once the Anti-Carjacking sequence has begun, the user has 59 seconds to press the V alet/Override Switch in order to cancel the sequence.

ORDER OF ANTI-CARJACKING SEQUENCE:

- For first 20 seconds after the sequence has begun there are no signs.

- From 21-30 seconds, the LED will blink slowly .

- From 31-45 seconds, the LED will blink fast and the siren/horn will chirp once every 2 seconds.

- From 46-60 seconds, the LED will blink fast and the siren/horn will chirp once per second.

- If not cancelled yet, at 61 seconds the alarm will trigger.

In the triggered condition:

- The siren/horn will sound & The parking lights will flash.

- The starter interrupt will engage. NOTE: Once the Anti-Carjack mode is triggered, the remote control will NOT

stop the operation, nor will the system reset automatically. Once it is trig-

gered, the Anti-Carjacking operation can only be deactivated by:

1) Turning the vehicle’ s ignition “Off”.

2) Turning the vehicle’ s ignition back “On”.

3) Within 10 seconds, Press & Release the V alet button.

Page 7

Valet Mode

Valet Mode can only be entered into while the alarm is Disarmed. Valet Mode turns off all of the alarm’s security features, (including Anti-Carjack).

Valet Mode is designed for situations in which it is not convenient for the security portion of the alarm to be operational; for example during extended stopovers for vehicle servicing, loaning others your vehicle, maintenance, valet parking, washing, etc. The convenience features such as keyless entry will still operate.

To Enter Valet Mode (Alarm MUST be Disarmed): Press & Hold the Valet Switch for 3 Seconds.

- The LED St atus Indicator will light solid Red and the siren will emit a long chirp to confirm entry into V alet Mode. Now the system cannot become Armed.

- The vehicle's ignition may be "On" or "Off" when entering Valet Mode.

- T o remind you it s in Valet Mode ,The siren will chirp every time the vehicle’s ignition is turned “Off”

To Exit Valet Mode: Simply Press & Release the Valet Switch.

- The LED will turn off and the siren will emit a long chirp to confirm that the system has exited V alet Mode. Normal arming operations may be resumed.

- The vehicle's ignition may be "On" or "Off" when exiting Valet Mode.

The LED Status Indicator

The Red LED Status Indicator visually shows the status of the alarm and also provides a high level of visual deterrence. The Red LED Status Indicator Light is normally mounted where it can be seen by the driver, as well as from outside.

Security System Status: The primary function of the Red LED Status Indicator Light is to indicate the normal operating status of the security system:

Off = The system is disarmed and not performing any automatic functions. On Constant = The system is in the Valet Mode. Flashing Slow = The system is fully Armed. Flashing Fast (while Disarmed) = Last Door Arming or Automatic Rearming.

Zone Violation: Once alarm is Disarmed, LED will show which zone triggered

alarm until the ignition is turned “On” (this clears unit’s memory).

2 flash & pause = Pin-Switch zone triggered alarm. 3 flash & pause = Door zone triggered alarm. 4 flash & pause = Sensor zone triggered alarm.

Automatic Transmitter Verification: For the first 90 seconds after the vehicle’s ignition is turned "On", the LED Status Indicator will flash a number of times equal to the number of remote control transmitters which are programmed to operate the alarm. This indication can be from 1 Flash /pause up to 4 Flashes /pause, as the system can be operated by just one, or as many as 4 remote transmitters.

Page 8

+ 18 hidden pages