Omega A, B User Manual

Model A and B

Dialtemp™ Dial Thermometers

INSTRUCTION

SHEET

M0055/0702

INSTALLING THE THERMOMETER

Model A and B Dial Thermometers are supplied
standard with a

1

⁄2" NPT hex mounting nut.
Carefully screw the thermometer into the fitting
by hand until slightly tight. Complete tightening
using a

7

⁄8" wrench on the hex nut. (See Figure

1). When using a thermowell, tighten only

FINGER TIGHT. CAUTION: NEVER TIGHTEN
BY TWISTING THE HEAD! To obtain a positive

seal, coat threads with pipe joint compound, or
use Teflon

®

tape.

When inserting Dialtemp™ Dial Thermometers
into semi-solid materials, hold stem firmly and
insert slowly and carefully to avoid bending. Do
not hold thermometer by the head when
inserting into a material, always hold by the
stem.

A

1

⁄4" NPT mounting nut, 3⁄4" NPT Adapter
bushing and plain hex bushing (with no
threads) are also available as mounting options
for the Model A and B Dial Thermometers.

It is not always desirable to permanently mount
Dialtemp™ Thermometers. Clip Hangers (Model
C-10) and Spring Handles (T-27) are available

as a mounting option. They are used for
mounting thermometers on the rim of tanks,
kettles, urns, solder pots, beakers and other
containers. Simply slide the metal clip onto the

1

⁄4" stem of the thermometer and lower it into the

liquid.

CAUTION: Avoid handling the thermometer
by the stem or bending the stem when
carrying it around.

SILICONE-FILLED THERMOMETERS

OMEGA provides the same features in its
special order silicone-filled thermometers as the
standard 3" and 5" styles. They are offered for
severe industrial applications where vibration is
a problem. Silicone is a non-toxic viscous fluid.
Its dampering characteristics prevent wear and
tear on internal parts and improve readability by
reducing flutter.

To specify, add “-SF” to the end of the part
number.

THERMOWELLS

Thermowells should be used whenever the

stem would be exposed to pressure, corrosion,
or shear forces. They also make it possible to
remove the thermometer without losing
pressure or contents.

OPERATING INSTRUCTIONS

For the correct temperature, the stem of the
Dial Thermometer must be immersed at least 2"
in fluids and 4" in gases. An exception to this
rule are thermometers with the ranges of 0­100°F, 24-125°F, and 0-50°C. These require at
least 3

1

⁄2" in liquid and 5" in gas.

TO RESET THE DIAL

1. Determine the room temperature using a
reference thermometer of known accuracy.

2. Firmly hold the hex mounting nut in the hand
or with a

7

⁄8" wrench.

3. While firmly holding the thermometer, slowly
turn the RESET SCREW with a screwdriver
(or

1

⁄4" wrench). The dial face INSIDE the
head will rotate as the screw is turned.
Slowly turn the reset screw until the proper
temperature on the dial face is aligned with
the pointer.

.250

Reset Screw

Specify stem length between these points

.69

3.00

.14

.31

.63

Mounting Nut – 1/2" NPT

MODEL A DIMENSIONS

FIGURE 1

SPECIFICATIONS:

ACCURACY: ±1% of full scale

RESPONSE TIME:

Readings are stabilized
within 40 seconds.

RECALIBRATION:

External with 1⁄4" nut reset
screw.

MATERIALS
CONSTRUCTION: Stainless steel welded

construction (rust and
corrosion-proof, leak-proof,
hermetically sealed)

HEAD & BEZEL: Polished Type 302

stainless steel.

MOUNTING NUT: Type 303 stainless steel,

7

⁄8" Hex, 1⁄2" HPT

DIAL FACE: Anodized aluminum with

raised black marks and
numbers with satin matte
finish background. Easy to
read. Minimum parallax.

STEM:

1

⁄4" Dia. 304 Stainless Steel
(highly resistant to
corrosion)

CRYSTAL: Optically clear strong

glass. Unbreakable clear
polycarbonate plastic
crystals are on all silicone­filled models which are not
recommended for ranges
over 300° F.

DIMENSIONS

HEAD DIAMETER:

Model A; 3" dia.
Model B; 5" dia.

STEM DIAMETER:1⁄4" dia.

STEM LENGTH: Standard is 9". Also

available: 2

1

⁄2", 4", 6", 12",
15", 18", 24", 30", 36"
(Stems over 36" are also
available, consult Sales
Department for pricing).
Intermediate lengths
available on special order
(allow 5 weeks). NOTE: A
4" stem is the shortest
length for ranges 0-100°F,
25-125°F, and 0-50°C.

POINTED STEMS:

Optional on all models.
They are excellent for
probing asphalt, compost,
soil, frozen foods and
other semi-solid materials.

RESET SCREWS:

1

⁄4" Hex Nut with slot for

.250

Reset Screw

Specify stem length between these points

.69

5.00

.14

.31

.63

Mounting Nut – 1/2" NPT

MODEL B DIMENSIONS

FIGURE 2

Teflon®is a registered trademark of DuPont.

150

100

200

250

300

®

350

400

°F

50

O

M

E

S

T

A

450

500

G

A

M

E

F

N

O

G

R

I

N

D

E

,

.

E

C

C

R

N

I

I

N

,

G

O

N

N

E

C

T

I

C

7

U

0

T

0

6

0

It is the policy of OMEGA to comply with all worldwide safety and EMC/EMI regulations that
apply. OMEGA is constantly pursuing certification of its products to the European New Approach
Directives. OMEGA will add the CE mark to every appropriate device upon certification.

The information contained in this document is believed to be correct, but OMEGA Engineering, Inc. accepts
no liability for any errors it contains, and reserves the right to alter specifications without notice.
WARNING: These products are not designed for use in, and should not be used for, patient-connected applications.

WARRANTY/DISCLAIMER

OMEGA ENGINEERING, INC. warrants this unit to be free of defects in materials and workmanship for a period of 13 months
from date of purchase. OMEGA’s WARRANTY adds an additional one (1) month grace period to the normal one (1) year
product warranty to cover handling and shipping time. This ensures that OMEGA’s customers receive maximum
coverage on each product.

If the unit malfunctions, it must be returned to the factory for evaluation. OMEGA’s Customer Service Department will issue an
Authorized Return (AR) number immediately upon phone or written request. Upon examination by OMEGA, if the unit is
found to be defective, it will be repaired or replaced at no charge. OMEGA’s WARRANTY does not apply to defects resulting
from any action of the purchaser, including but not limited to mishandling, improper interfacing, operation outside of design
limits, improper repair, or unauthorized modification. This WARRANTY is VOID if the unit shows evidence of having been
tampered with or shows evidence of having been damaged as a result of excessive corrosion; or current, heat, moisture or
vibration; improper specification; misapplication; misuse or other operating conditions outside of OMEGA’s control.
Components which wear are not warranted, including but not limited to contact points, fuses, and triacs.

OMEGA is pleased to offer suggestions on the use of its various products. However, OMEGA neither assumes
responsibility for any omissions or errors nor assumes liability for any damages that result from the use of its
products in accordance with information provided by OMEGA, either verbal or written. OMEGA warrants only that
the parts manufactured by it will be as specified and free of defects. OMEGA MAKES NO OTHER WARRANTIES OR
REPRESENTATIONS OF ANY KIND WHATSOEVER, EXPRESS OR IMPLIED, EXCEPT THAT OF TITLE, AND ALL IMPLIED
WARRANTIES INCLUDING ANY WARRANTY OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
ARE HEREBY DISCLAIMED. LIMITATION OF LIABILITY: The remedies of purchaser set forth herein are exclusive, and
the total liability of OMEGA with respect to this order, whether based on contract, warranty, negligence,
indemnification, strict liability or otherwise, shall not exceed the purchase price of the component upon which
liability is based. In no event shall OMEGA be liable for consequential, incidental or special damages.

CONDITIONS: Equipment sold by OMEGA is not intended to be used, nor shall it be used: (1) as a “Basic Component” under
10 CFR 21 (NRC), used in or with any nuclear installation or activity; or (2) in medical applications or used on humans. Should
any Product(s) be used in or with any nuclear installation or activity, medical application, used on humans, or misused in any
way, OMEGA assumes no responsibility as set forth in our basic WARRANTY/ DISCLAIMER language, and, additionally,
purchaser will indemnify OMEGA and hold OMEGA harmless from any liability or damage whatsoever arising out of the use
of the Product(s) in such a manner.

RETURN REQUESTS / INQUIRIES

Direct all warranty and repair requests/inquiries to the OMEGA Customer Service Department. BEFORE RETURNING ANY
PRODUCT(S) TO OMEGA, PURCHASER MUST OBTAIN AN AUTHORIZED RETURN (AR) NUMBER FROM OMEGA’S
CUSTOMER SERVICE DEPARTMENT (IN ORDER TO AVOID PROCESSING DELAYS). The assigned AR number should then
be marked on the outside of the return package and on any correspondence.

The purchaser is responsible for shipping charges, freight, insurance and proper packaging to prevent breakage in transit.

FOR W

ARRANTY RETURNS, please have the following

information available BEFORE contacting OMEGA:

1. Purchase Order number under which the product was
PURCHASED,

2. Model and serial number of the product under
warranty, and

3. Repair instructions and/or specific problems relative to
the product.

FOR NON-W

ARRANTY

REPAIRS,

consult OMEGA for
current repair charges. Have the following information
available BEFORE contacting OMEGA:

1. Purchase Order number to cover the COST of the repair,

2. Model and serial number of the product, and

3. Repair instructions and/or specific problems relative to

the product.

OMEGA’s policy is to make running changes, not model changes, whenever an improvement is possible. This affords our customers the latest in
technology and engineering.

OMEGA is a registered trademark of OMEGA ENGINEERING, INC.
© Copyright 2002 OMEGA ENGINEERING, INC. All rights reserved. This document may not be copied, photocopied, reproduced, translated, or reduced

to any electronic medium or machine-readable form, in whole or in part, without the prior written consent of OMEGA ENGINEERING, INC.

Servicing North America:

USA: One Omega Drive, Box 4047

ISO 9001 Certified Stamford CT 06907-0047

Tel: [phone] FAX: [phone]
e-mail: [e-mail]

Canada: 976 Bergar

Laval (Quebec) H7L 5A1
Tel: [phone] FAX: [phone]
e-mail: [e-mail]

For immediate technical or application assistance:

USA and Canada: Sales Service: 1-800-826-6342 / 1-800-TC-OMEGA

®

Customer Service: 1-800-622-2378 / 1-800-622-BEST

®

Engineering Service: 1-800-872-9436 / 1-800-USA-WHEN

®

TELEX: 996404 EASYLINK: 62968934 CABLE: OMEGA

Mexico: En Espan˜ol: [phone]-7803 e-mail:[e-mail]

FAX: [phone] [e-mail]

OMEGAnet®Online Service Internet e-mail

www.omega.com [e-mail]

Servicing Europe:

Benelux: Postbus 8034, 1180 LAAmstelveen, The Netherlands

Tel: [phone] FAX: [phone]
Toll Free in Benelux: 0800 0993344
e-mail: [e-mail]

Czech Republic: Rudé armády 1868, 733 01 Karviná 8

Tel: [phone] FAX: [phone]
Toll Free: 0800-1-66342 e-mail: [e-mail]

France: 11, rue Jacques Cartier, 78280 Guyancourt, France

Tel: [phone] FAX: [phone]
Toll Free in France: 0800 466 342
e-mail: [e-mail]

Germany/Austria: Daimlerstrasse 26, D-75392 Deckenpfronn, Germany

Tel: [phone] FAX: [phone]
Toll Free in Germany: 0800 639 7678
e-mail: [e-mail]

United Kingdom: One Omega Drive, River Bend Technology Centre

ISO 9002 Certified Northbank, Irlam, Manchester

M44 5BD United Kingdom
Tel: [phone] FAX: [phone]
Toll Free in United Kingdom: 0800-488-488
e-mail: [e-mail]