Omcan SE-CN-0203 Operators Manual

Impulse Sealers
Models SE-CN-0203, 0305, 0406 and 0508
Items 14446, 14448, 14450, 14451
Revised - 02/07/2018
Toll Free: 1-800-465-0234
Fax: 905-607-0234
Email: service@omcan.com
www.omcan.com
Table of Contents
Model SE-CN-0203 / Model SE-CN-0305 Model SE-CN-0406 / Model SE-CN-0508
Section
General Information
Safety and Warranty
Technical Specications
Operation
Parts Breakdown
Electrical Schematics
----------------------------------------------------------------------------------------- 6 - 7
--------------------------------------------------------------------------- 3 - 4
--------------------------------------------------------------------------- 4 - 5
------------------------------------------------------------------------------- 7 - 9
---------------------------------------------------------------------------- 10
Page
---------------------------------------------------------------------- 5 - 6
Warranty Registration
---------------------------------------------------------------------------- 11
2
General Information
Omcan Manufacturing and Distributing Company Inc., Food Machinery of America, Inc. dba Omcan and Omcan Inc. are not responsible for any harm or injury caused due to any person’s improper or negligent use of this equipment. The product shall only be operated by someone over the age of 18, of
sound mind, and not under the inuence of any drugs or alcohol, who has been trained in the correct operation of this machine, and is wearing authorized, proper safety clothing. Any modication to the machine voids any warranty, and may cause harm to individuals using the machine or in the vicinity of the machine while in operation.
CHECK PACKAGE UPON ARRIVAL
Upon receipt of an Omcan shipment please inspect for external damage. If no damage is evident on the external packaging, open carton to ensure all ordered items are within the box, and there is no concealed damage to the machine. If the package has suffered rough handling, bumps or damage (visible or concealed), please note it on the bill of lading before accepting the delivery and contact Omcan within 24 hours, so we may initiate a claim with the carrier. A detailed report on the extent of the damage caused to the machine must be
lled out within three days, from the delivery date shown in the shipping documents. Omcan has no recourse
for damaged products that were shipped collect or third party.
Before operating any equipment, always read and familiarize yourself with all operation and safety
instructions.
Omcan would like to thank you for purchasing this machine. It’s of the utmost importance to save these instructions for future reference. Also save the original box and packaging for shipping the
equipment if servicing or returning of the machine is required.
---------------------------------------------------------------------------------------------------------------------------------------------------
Omcan Fabrication et distribution Companie Limité et Food Machinery d’Amerique, dba Omcan et Omcan Inc. ne sont pas responsables de tout dommage ou blessure causé du fait que toute personne ait utilisé cet équipement de façon irrégulière. Le produit ne doit être exploité que par quelqu’un de
plus de 18 ans, saine d’esprit, et pas sous l’inuence d’une drogue ou d’acohol, qui a été formé pour utiliser cette machine correctement, et est vêtu de vêtements de sécurité approprié. Toute modication
de la machine annule toute garantie, et peut causer un préjudice à des personnes utilisant la machine ou des personnes à proximité de la machine pendant son fonctionnement.
VÉRIFIEZ LE COLIS DÈS RÉCEPTION
Dès réception d’une expédition d’Omcan veuillez inspecter pour dommages externes. Si aucun dommage
n’est visible sur l’emballage externe, ouvrez le carton an de s’assurer que tous les éléments commandés
sont dans la boîte, et il n’y a aucun dommage dissimulé à la machine. Si le colis n’a subi aucune mauvaises manipulations, de bosses ou de dommages (visible ou cachée), notez-le sur le bond de livraison avant
d’accepter la livraison et contactez Omcan dans les 24 heures qui suivent, pour que nous puissions engager
une réclamation auprès du transporteur. Un rapport détaillé sur l’étendue des dommages causés à la machine
doit être rempli dans un délai de trois jours, à compter de la date de livraison indiquée dans les documents d’expédition. Omcan n’a aucun droit de recours pour les produits endommagés qui ont été expédiées ou cueilli
par un tiers transporteur.
3
General Information
Avant d’utiliser n’importe quel équipement, toujours lire et vous familiariser avec toutes les opérations et les consignes de sécurité.
Omcan voudrais vous remercier d’avoir choisi cette machine. Il est primordial de conserver ces
instructions pour une référence ultérieure. Également conservez la boîte originale et l’emballage pour
l’expédition de l’équipement si l’entretien ou le retour de la machine est nécessaire.
---------------------------------------------------------------------------------------------------------------------------------------------------
Omcan Empresa De Fabricacion Y Distribucion Inc. Y Maquinaria De Alimentos De America, Inc. dba Omcan y Omcan Inc. no son responsables de ningun daño o perjuicío causado por cualquier persona inadecuada o el uso descuidado de este equipo. El producto solo podra ser operado por una persona
mayor de 18 años, en su sano juicio y no bajo alguna inuencia de droga o alcohol, y que este ha sido entrenado en el correcto funcionamiento de esta máquina, y ésta usando ropa apropiada y autorizada. Cualquier modicación a la máquina anúla la garantía y puede causar daños a las personas usando la
máquina mientras esta en el funcionamiento.
REVISE EL PAQUETE A SU LLEGADA
Tras la recepcion de un envio Omcan favor inspeccionar daños externos. Si no hay daños evidentes en el
empaque exterior, Habra el carton para asegurararse que todos los articulos solicitados ésten dentro de la caja y no encuentre daños ocultos en la máquina. Si el paquete ha sufrido un manejo de poco cuidado, golpes
o daños (visible o oculto) por favor anote en la factura antes de aceptar la entrega y contacte Omcan dentro
de las 24 horas, de modo que podamos iniciar una reclamación con la compañia. Un informe detallado sobre los daños causados a la máquina debe ser llenado en el plazo de tres días, desde la fecha de entrega que se muestra en los documentos de envío. Omcan no tiene ningun recurso por productos dañados que se enviaron
a recoger por terceros.
Antes de utilizar cualquier equipo, siempre lea y familiarizarse con todas las instrucciones de
funcionamiento y seguridad.
Omcan le gustaría darle las gracias por la compra de esta máquina. Es de la mayor importancia para salvar estas instrucciones para futuras consultas. Además, guarda la caja original y el embalaje para el
envío del equipo si servicio técnico o devolución de la máquina que se requiere.
Safety and Warranty
The Impulse Sealer is used to ensure a water tight and air tight seal for effective packing and sterilization procedures.
Place the unit on a at, level surface.
Do not place any ammable or explosive objects around the unit.
Thoroughly read this manual before installing the unit.
Always keep the sealing platform clean. Leaving residue will reduce the life of the element, non-stick
4
Safety and Warranty
material and silicon rubber.
Never use water to clean the sealing surface.
Replace torn non-stick material immediately. A torn surface will short circuit the element and damage the
unit. Every time you replace the element, replace the lower and upper non-stick material.
For best operation, use only genuine replacement parts.
A worn silicon rubber will inuence the seal, change the silicon when worn or burned.
1 YEAR PARTS AND LABOUR BENCH WARRANTY
Within the warranty period, contact Omcan Inc. At 1-800-465-0234 to schedule a drop off to either an Omcan authorized service depot in the area, or to an Omcan Service warehouse to repair the
equipment.
Unauthorized maintenance will void the warranty. Warranty covers electrical and part failures, not
improper use.
Please see www.omcan.com/warranty.html for complete info.
WARNING:
The packaging components (cardboard, polyethylene, and others) are classied as normal solid urban waste and can therefore be disposed of without difculty.
In any case, for suitable recycling, we suggest disposing of the products separately (differentiated waste) according to the current norms.
DO NOT DISCARD ANY PACKAGING MATERIALS IN THE ENVIRONMENT!
Technical Specications
Model SE-CN-0203 SE-CN-0305 SE-CN-0406 SE-CN-0508 Seal Bar Length 8” / 203mm 12” / 305mm 16” / 406mm 20” / 508mm Electrical 110V/60/1 Weight 5.3 lbs. / 2.4 kgs. 8.8 lbs. / 4 kgs. 10 lbs. / 4.5 kgs. 13 lbs. / 5.9 kgs. Item Number 14446 14448 14450 14451
The unit features:
Compact Design.
Strong Water Tight Seal.
5
Technical Specications
Fast Operation.
Precise Electric Circuit.
Long Lasting.
MAIN COMPONENTS
1. Handle Knob.
2. Platen Arm.
3. Platen Spring.
4. Platen.
5. Silicon Rubber.
6. Swivel.
7. Hinge.
8. Hinge Bracket.
9. Enclosure.
10. Metal Plate.
11. Lower Element non­stick material.
12. Upper non-stick material Cloth.
13. Strain Relief Busing.
14. Power Supply Cord.
15. Heating Element.
16. Pilot Lamp.
17. Timer Knob.
18. Control Panel.
19. Variable Resistor.
20. Switch Level.
Operation
1. Plug the cord into a grounded outlet. You do not need to switch the machine on. The machine will operate only when the arm is down. Control the timer according to the thickness of the material to be sealed. Use a higher setting for thicker material. Pull the handle down to seal. Sealing takes place when the light it on. Leave the arm down for an additional few seconds after the light turns off to obtain a better seal.
2. Use a lower setting if the seal burns through.
3. Raise to a higher setting if the seal is not tight enough.
4. Should the bag stick to the silicon rubber, you did not give it enough time to cool.
5. Once you set the time, there is no need to reset it as the machine will remain constant and unchanged.
6
Operation
REFERENCE
Item Number Model Number Description Manufacturer Model Number
14446 SE-CN-0203 Sealer Impulse 8” / 203mm Bar 110V/60/1 PFS-08
14448 SE-CN-0305 Sealer Impulse 12” 305mm Bar 110V/60/1 PFS-12 14450 SE-CN-0406 Sealer Impulse 16” 406mm Bar 110V/60/1 PFS-16
14451 SE-CN-0508 Sealer Impulse 20” 508mm Bar 110V/60/1 PFS-20
Parts Breakdown
Model SE-CN-0203 14446 Model SE-CN-0305 14448 Model SE-CN-0406 14450 Model SE-CN-0508 14451
7
Parts Breakdown
Model SE-CN-0203 14446
Item No. Description Position Item No. Description Position
76813 Main Housing for PFS-08 01 19424 Spring for PFS-08 10 19426 Bracket for PFS-08 19
76814 Hand Lever for PFS-08 02 76816 Hand Lever Pin for PFS-08 11 76823 Lever Hand Knob for PFS-08 20
17736 Timer Assembly for PFS-08 03 76817 Hand Lever Bracket for PFS-08 12 76824 Bottom Plate Housing for PFS-08 21
19197 Transformer - 110V for PFS-08 04 76818 Tension Spring Element for PFS-08 13 16029 Rubber Foot for PFS-08 22
19422 Aluminum Bar for PFS-08 05 76819 Fulcrum Lever for PFS-08 14 76825 Pressure Bar Pin for PFS-08 23
19423 Rubber Seal for PFS-08 06 16028 Lever Hand Spring for PFS-08 15 19425 Teon Strip for PFS-08 24
76815
25192 Element Insulator for PFS-08 08 76821 Microswitch for PFS-08 17
19428 Teon Cover Plate for PFS-08 09 76822 Power with Plug Cord for PFS-08 18
Sealing Band Element Trim Wire Element for PFS-08
07 76820 Microswitch Bracket for PFS-08 16 16039 Element Service Kit for PFS-08 25
Item No.
Description Position
Model SE-CN-0305 14448
Item No. Description Position Item No. Description Position
77319 Main Housing for PFS-12 01 19424 Spring for PFS-12 10 19426 Bracket for PFS-12 19
77320 Hand Lever for PFS-12 02 76816 Hand Lever Pin for PFS-12 11 16032 Lever Hand Knob for PFS-12 20
16030 Timer Assembly for PFS-12 03 76817 Hand Lever Bracket for PFS-12 12 64888 Bottom Plate Housing for PFS-12 21
19198 Transformer - 110V for PFS-12 04 76818 Tension Spring Element for PFS-12 13 16033 Rubber Foot for PFS-12 22
19421 Aluminum Bar for PFS-12 05 76819 Fulcrum Lever for PFS-12 14 76825 Pressure Bar Pin for PFS-12 23
21106 Rubber Seal for PFS-12 06 77321 Lever Hand Spring for PFS-12 15 77322 Teon Strip for PFS-12 24
64151
25192 Element Insulator for PFS-12 08 19430 Microswitch for PFS-12 17
19427 Teon Cover Plate for PFS-12 09 76822 Power with Plug Cord for PFS-12 18
Sealing Band Element Trim Wire Element for PFS-12
07 76820 Microswitch Bracket for PFS-12 16 16040 Element Service Kit for PFS-12 25
Item No.
Description Position
8
Model SE-CN-0406 14450
Parts Breakdown
Item No. Description Position Item No. Description Position
77323 Main Housing for PFS-16 01 19424 Spring for PFS-16 10 19426 Bracket for PFS-16 19
77324 Hand Lever for PFS-16 02 76816 Hand Lever Pin for PFS-16 11 77329 Lever Hand Knob for PFS-16 20
16037 Timer Assembly for PFS-16 03 76817 Hand Lever Bracket for PFS-16 12 64889 Bottom Plate Housing for PFS-16 21
19199 Transformer - 110V for PFS-16 04 76818 Tension Spring Element for PFS-16 13 77330 Rubber Foot for PFS-16 22
21102 Aluminum Bar for PFS-16 05 76819 Fulcrum Lever for PFS-16 14 76825 Pressure Bar Pin for PFS-16 23
77325 Rubber Seal for PFS-16 06 77327 Lever Hand Spring for PFS-16 15 77331 Teon Strip for PFS-16 24
64152
25192 Element Insulator for PFS-16 08 77328 Microswitch for PFS-16 17
77326 Teon Cover Plate for PFS-16 09 76822 Power with Plug Cord for PFS-16 18
Sealing Band Element Trim Wire Element for PFS-16
07 76820 Microswitch Bracket for PFS-16 16 16041 Element Service Kit for PFS-16 25
Item No.
Description Position
Model SE-CN-0508 14451
Item No. Description Position Item No. Description Position
77332 Main Housing for PFS-20 01 19424 Spring for PFS-20 10 19426 Bracket for PFS-20 19
77333 Hand Lever for PFS-20 02 76816 Hand Lever Pin for PFS-20 11 77339 Lever Hand Knob for PFS-20 20
16038 Timer Assembly for PFS-20 03 76817 Hand Lever Bracket for PFS-20 12 64890 Bottom Plate Housing for PFS-20 21
19200 Transformer - 110V for PFS-20 04 76818 Tension Spring Element for PFS-20 13 77340 Rubber Foot for PFS-20 22
77334 Aluminum Bar for PFS-20 05 76819 Fulcrum Lever for PFS-20 14 76825 Pressure Bar Pin for PFS-20 23
77335 Rubber Seal for PFS-20 06 77337 Lever Hand Spring for PFS-20 15 77341 Teon Strip for PFS-20 24
64153
25192 Element Insulator for PFS-20 08 77338 Microswitch for PFS-20 17
77336 Teon Cover Plate for PFS-20 09 76822 Power with Plug Cord for PFS-20 18
Sealing Band Element Trim Wire Element for PFS-20
07 76820 Microswitch Bracket for PFS-20 16 16042 Element Service Kit for PFS-20 25
Item No.
Description Position
9
Electrical Schematics
Model SE-CN-0203 14446 Model SE-CN-0305 14448 Model SE-CN-0406 14450 Model SE-CN-0508 14451
10
Warranty Registration
Thank you for purchasing an Omcan product. To register your warranty for this product, complete the information below, tear off the card at
the perforation and then send to the address specied below. You can also register online by visiting:
Merci d’avoir acheté un produit Omcan. Pour enregistrer votre garantie pour ce produit, complétez les informations ci-dessous, détachez la
carte au niveau de la perforation, puis l’envoyer à l’adresse spécié ci-dessous. Vous pouvez également vous inscrire en ligne en visitant:
Gracias por comprar un producto Omcan usted. Para registrar su garantía para este producto, complete la información a continuación, cortar la tarjeta en la perforación y luego enviarlo a la dirección indicada a continuación. También puede registrarse en línea en:
www.omcan.com/warrantyregistration.html
For mailing in Canada
Pour postale au Canada
Por correo en Canadá
OMCAN
PRODUCT WARRANTY REGISTRATION
3115 Pepper Mill Court,
Mississauga, Ontario
Canada, L5L 4X5
PRODUCT WARRANTY REGISTRATION
4450 Witmer Industrial Estates, Unit 4,
For mailing in the US
Pour diffusion aux États-Unis
Por correo en los EE.UU.
OMCAN
Niagara Falls, New York
USA, 14305
or email to: service@omcan.com
Purchaser’s Information
Name: Company Name:
Address:
Telephone:
City: Province or State: Postal or Zip: Email Address:
Country: Type of Company:
Restaurant Bakery Deli
Dealer from which Purchased: Butcher Supermarket Caterer
Dealer City: Dealer Province or State: Institution (specify):
Invoice: Other (specify):
Model Name: Model Number: Serial Number:
Machine Description:
Date of Purchase (MM/DD/YYYY): Date of Installation (MM/DD/YYYY):
Would you like to extend the warranty? Yes No
Thank you for choosing Omcan | Merci d’avoir choisi Omcan | Gracias por elegir Omcan
11
Since 1951 Omcan has grown to become a leading distributor of equipment and supplies to the North American food service industry. Our success over these many years can be attributed to our commitment to strengthen and develop new and existing relationships with our valued customers and manufacturers. Today with partners in North America, Europe, Asia and South America, we continually work to improve
and grow the company. We strive to offer customers exceptional value through our qualied local sales
and service representatives who provide convenient access to over 3,500 globally sourced products.
Depuis 1951 Omcan a grandi pour devenir un des “leaders” de la distribution des équipements et matériel pour l’industrie des services alimentaires en Amérique du Nord. Notre succès au cours de ces nombreuses années peut être attribué à notre engagement à renforcer et à développer de nouvelles et existantes relations avec nos clients et les fabricants de valeur. Aujourd’hui avec des partenaires en Amérique du Nord, Europe, Asie et Amérique du Sud, nous travaillons continuellement à améliorer et développer l’entreprise. Nous nous efforçons d’offrir à nos clients une valeur exceptionnelle grâce à
nos ventes locales qualiées et des représentants de service qui offrent un accès facile à plus de 3500
produits provenant du monde entier.
Desde 1951 Omcan ha crecido hasta convertirse en un líder en la distribución de equipos y suministros de alimentos en América del Norte industria de servicios. Nuestro éxito en estos años se puede atribuir a nuestro compromiso de fortalecer y desarrollar nuevas relaciones existentes con nuestros valiosos clientes y fabricantes. Hoy con socios de América del Norte, Europa, Asia y América del Sur, que trabajan continuamente para mejorar y crecer la empresa. Nos esforzamos por ofrecer a nuestros clientes valor excepcional a través de nuestro local de ventas y representantes de los servicios que proporcionan un fácil acceso a más de 3,500 productos con origen a nivel mundial.
Loading...