Omcan SANTOS 01PV Operators Manual

Santos Poppy Seed Grinder

Model Santos 01PV

Items 44116

Instruction Manual

Revised - 01/21/2020

Toll Free: 1-800-465-0234

Fax: 905-607-0234

Email: service@omcan.com

www.omcan.com

Table of Contents

Model Santos 01PV

Section

General Information

Safety and Warranty

Technical Specications

Operation

Maintenance

Troubleshooting

--------------------------------------------------------------------------------------------- 7

------------------------------------------------------------------------------------- 7 - 8

--------------------------------------------------------------------------- 3 - 4

--------------------------------------------------------------------------- 4 - 6

-------------------------------------------------------------------------------- 8 - 9

Page

-------------------------------------------------------------------------- 6

Figure Drawings

Parts Breakdown

Electrical Schematics

Notes

Warranty Registration

------------------------------------------------------------------------------------------- 16 - 18

----------------------------------------------------------------------------- 10 - 11

---------------------------------------------------------------------------- 12 - 14

---------------------------------------------------------------------------- 15

---------------------------------------------------------------------------- 19

2

General Information

Omcan Manufacturing and Distributing Company Inc., Food Machinery of America, Inc. dba Omcan and Omcan Inc. are not responsible for any harm or injury caused due to any person’s improper or negligent use of this equipment. The product shall only be operated by someone over the age of 18, of

sound mind, and not under the inuence of any drugs or alcohol, who has been trained in the correct operation of this machine, and is wearing authorized, proper safety clothing. Any modication to the machine voids any warranty, and may cause harm to individuals using the machine or in the vicinity of the machine while in operation.

CHECK PACKAGE UPON ARRIVAL

Upon receipt of an Omcan shipment please inspect for external damage. If no damage is evident on the external packaging, open carton to ensure all ordered items are within the box, and there is no concealed

damage to the machine. If the package has su󰀨ered rough handling, bumps or damage (visible or concealed),

please note it on the bill of lading before accepting the delivery and contact Omcan within 24 hours, so we may initiate a claim with the carrier. A detailed report on the extent of the damage caused to the machine must be

lled out within three days, from the delivery date shown in the shipping documents. Omcan has no recourse

for damaged products that were shipped collect or third party.

Before operating any equipment, always read and familiarize yourself with all operation and safety

instructions.

Omcan would like to thank you for purchasing this machine. It’s of the utmost importance to save these instructions for future reference. Also save the original box and packaging for shipping the

equipment if servicing or returning of the machine is required.

---------------------------------------------------------------------------------------------------------------------------------------------------

Omcan Fabrication et distribution Companie Limité et Food Machinery d’Amerique, dba Omcan et Omcan Inc. ne sont pas responsables de tout dommage ou blessure causé du fait que toute personne ait utilisé cet équipement de façon irrégulière. Le produit ne doit être exploité que par quelqu’un de

plus de 18 ans, saine d’esprit, et pas sous l’inuence d’une drogue ou d’acohol, qui a été formé pour utiliser cette machine correctement, et est vêtu de vêtements de sécurité approprié. Toute modication

de la machine annule toute garantie, et peut causer un préjudice à des personnes utilisant la machine ou des personnes à proximité de la machine pendant son fonctionnement.

VÉRIFIEZ LE COLIS DÈS RÉCEPTION

Dès réception d’une expédition d’Omcan veuillez inspecter pour dommages externes. Si aucun dommage

n’est visible sur l’emballage externe, ouvrez le carton an de s’assurer que tous les éléments commandés

sont dans la boîte, et il n’y a aucun dommage dissimulé à la machine. Si le colis n’a subi aucune mauvaises

manipulations, de bosses ou de dommages (visible ou cachée), notez-le sur le bond de livraison avant d’accepter la livraison et contactez Omcan dans les 24 heures qui suivent, pour que nous puissions engager

une réclamation auprès du transporteur. Un rapport détaillé sur l’étendue des dommages causés à la machine

doit être rempli dans un délai de trois jours, à compter de la date de livraison indiquée dans les documents d’expédition. Omcan n’a aucun droit de recours pour les produits endommagés qui ont été expédiées ou cueilli

par un tiers transporteur.

3

General Information

Avant d’utiliser n’importe quel équipement, toujours lire et vous familiariser avec toutes les opérations et les consignes de sécurité.

Omcan voudrais vous remercier d’avoir choisi cette machine. Il est primordial de conserver ces

instructions pour une référence ultérieure. Également conservez la boîte originale et l’emballage pour

l’expédition de l’équipement si l’entretien ou le retour de la machine est nécessaire.

---------------------------------------------------------------------------------------------------------------------------------------------------

Omcan Empresa De Fabricacion Y Distribucion Inc. Y Maquinaria De Alimentos De America, Inc. dba Omcan y Omcan Inc. no son responsables de ningun daño o perjuicío causado por cualquier persona inadecuada o el uso descuidado de este equipo. El producto solo podra ser operado por una persona

mayor de 18 años, en su sano juicio y no bajo alguna inuencia de droga o alcohol, y que este ha sido entrenado en el correcto funcionamiento de esta máquina, y ésta usando ropa apropiada y autorizada. Cualquier modicación a la máquina anúla la garantía y puede causar daños a las personas usando la

máquina mientras esta en el funcionamiento.

REVISE EL PAQUETE A SU LLEGADA

Tras la recepcion de un envio Omcan favor inspeccionar daños externos. Si no hay daños evidentes en el

empaque exterior, Habra el carton para asegurararse que todos los articulos solicitados ésten dentro de la caja y no encuentre daños ocultos en la máquina. Si el paquete ha sufrido un manejo de poco cuidado, golpes o daños (visible o oculto) por favor anote en la factura antes de aceptar la entrega y contacte Omcan dentro de las 24 horas, de modo que podamos iniciar una reclamación con la compañia. Un informe detallado sobre los daños causados a la máquina debe ser llenado en el plazo de tres días, desde la fecha de entrega que se muestra en los documentos de envío. Omcan no tiene ningun recurso por productos dañados que se enviaron

a recoger por terceros.

Antes de utilizar cualquier equipo, siempre lea y familiarizarse con todas las instrucciones de

funcionamiento y seguridad.

Omcan le gustaría darle las gracias por la compra de esta máquina. Es de la mayor importancia para salvar estas instrucciones para futuras consultas. Además, guarda la caja original y el embalaje para el

envío del equipo si servicio técnico o devolución de la máquina que se requiere.

Safety and Warranty

IMPROPER USE

1. Do not use this appliance for grinding anything other than poppy seeds.

2. Never operate the appliance with no poppy seeds in the container.

3. Remove from the poppy seeds any foreign bodies which may damage the grinding wheels (metal staples,

stones, etc.).

4. For electrocution risk protection reasons, never plunge the base into water or any other liquid.

4

Safety and Warranty

5. Do not use a hose or a pressure hose for cleaning: this is forbidden.

6. Never touch the moving parts.

7. Unplug the appliance before carrying out any work on it: cleaning, maintenance or repair.

8. Do not use the appliance if the power cord is damaged. It must be replaced by a special assembly available from an approved Omcan dealer or from Omcan itself.

9. The use of spare parts other than certied Omcan original parts is prohibited.

10. Turn the On/O󰀨 switch (11) to “0” when the appliance is not operating.

11. Do not connect several appliances to the same power socket.

12. Do not use the appliance outdoors.

13. Never place the appliance close to or on a source of heat.

14. This appliance is a professional machine designed exclusively for professional use. It is not designed for household use.

15. This appliance is not designed for use by people (including children) whose physical, sensorial or mental capacities are impaired or by people with no experience or knowledge, unless they have been supervised or given training in the use of the appliance beforehand by a person responsible for their safety. Supervise children to ensure they do not play with the appliance.

ELECTRICAL CONNECTION

Line protection: The appliance should be connected to a standard 2-pole + ground electric socket. The

installation should be tted with an RCD and a fuse rated at 16A. The appliance must be grounded.

CARE

Before connecting the machine, check that the mains electrical voltage is the same as the voltage for your appliance. If the power cable is damaged, it should be replaced by a Omcan approved dealer, Omcan or a

person with similar qualications to avoid any danger.

Make sure that the on / o󰀨 switch (13) is on 0 position before plugging the power cord into the main supply socket (Fig. A.)

RECYCLING THE PRODUCT AT THE END OF ITS SERVICE LIFE

This equipment is marked with the selective sorting symbol relating to wastes from electrical and electronic equipment. It signies that this product should be taken over by a selective collection system conforming to the Guideline 2002/96/EC (WEEE) – part Professional Equipment – so that it can be either recycled or dismantled

in order to reduce any impact on the environment. For more information, please contact your Retailer or

Omcan. For eliminating or recycling components of equipment, please contact a specialized company or

contact Omcan. The electronic products not undergoing a selective sorting are potentially dangerous for the environment. The damaging materials should be eliminated or recycled according to the regulations in force.

1 YEAR PARTS AND LABOUR BENCH WARRANTY

Within the warranty period, contact Omcan Inc. at 1-800-465-0234 to schedule a drop o󰀨 to either

5

Safety and Warranty

an Omcan authorized service depot in the area, or to an Omcan Service warehouse to repair the

equipment.

Unauthorized maintenance will void the warranty. Warranty covers electrical and part failures, not

improper use.

Please see https://omcan.com/disclaimer for complete info.

WARNING:

The packaging components are classied as normal solid urban waste and can therefore be disposed of without di󰀩culty.

In any case, for suitable recycling, we suggest disposing of the products separately (di󰀨erentiated waste) according to the current norms.

DO NOT DISCARD ANY PACKAGING MATERIALS IN THE ENVIRONMENT!

Technical Specications

MAIN TECHNICAL PARAMETERS

Model Santos 01PV Electrical 110V / 60Hz / 1Ph

Power 650 W / 0.87 Hp

Current 5.9A RPM 1800 Production per Hour 31 lbs. / 14 kgs. Dimensions 13” x 10” x 22” / 320 x 250 x 550mm

Packaging Dimensions 12” x 16” x 23” / 300 x 410 x 575mm

Weight 31 lbs. / 14 kgs.

Packaging Weight 36 lbs. / 16 kgs.

Item Number 44116

6

Operation

ADJUSTING THE GRIND

• Turn the grinding-wheel gap adjuster button (6) clockwise for a coarser grind and counterclockwise for a ner grind. The factory setting is for the nest grind, with the grinding-wheels nearly touching each other.

SERVICING

• Clean the dispensing outlet, the poppy seed holder and the grinding mechanism from time to time. Always

turn the appliance o󰀨 (switch 13 on position 0) and unplug it.

Maintenance

Before carrying out any work on the appliance, it must in all cases be unplugged from the mains power supply and the motor start capacitor discharged:

DISCHARGING THE CAPACITOR:

Use a screwdriver with insulated handle to touch the 2 connectors on the capacitor (13). The appearance of an

electric arc shows that the capacitor has discharged.

SPARE PARTS:

This machine requires no specic maintenance. The bearings are lubricated for life. If work is required to

replace worn parts such as the grindstones or the electric or other components, refer to the parts list.

IMPORTANT: It is prohibited to use spare parts other than those certied by Omcan

For all spare part orders (see references in the exploded view at the end of the manual), state:

• The type.

• The machine serial number.

• The electrical specications recorded under the machine.

REPLACING THE GRINDSTONES

IMPORTANT: always change both 2 grindstones (17) at the same time.

The 2 grinding wheels are identical and can be tted equally either on the moving plate (18) (moving grinding wheel) or on the cast metal adjustment block (19) (xed grinding wheel).

1. Stop the machine by putting the switch (13) to “0” and disconnect the power supply cord.

2. Close the shutter (3) on the hopper (2). Take o󰀨 the hopper (2).

3. Turn the grinding wheel gap adjuster button (6) clockwise until it comes to a halt at the “COARSE” setting.

4. Unscrew the nuts (16) and remove the whole grinding unit (15), to gain access to the grinding wheels.

5. Change the grinding wheels (3 fastening screws) after carefully cleaning the supporting surfaces.

TAKE CARE: The slightest small co󰀨ee particle under the grinding wheel may prevent the machine

7

Maintenance

from operating correctly. It is recommended that the grinder body is cleaned with a compressed air

jet or a dry brush.

6. Reassemble the grinding unit (15) and adjust the grinding gap to its minimum setting.

TAKE CARE: Before tightening the fastening nuts (16) on the grinding unit (15), check that the dial (4) of the grinding wheel adjuster button (6) is set to “COARSE”. This precaution is essential to prevent any risk of the grinding wheels being brought too close to each other, which could cause damage to

the grinding unit.

ADJUSTING THE MINIMUM GAP BETWEEN THE GRINDING-WHEELS

This should be done after replacing the grinding wheels.

1. Plug the appliance in and run it empty.

2. Unscrew hexagon socket screw (7) on the dial (4) using a 2-mm Allen wrench. Check that the dial (4) is

free to rotate without turning button (6).

3. Turn button (6) counterclockwise until the grinding wheels come into contact (a slight sound of friction will be heard) then back one notch in the reverse direction.

ATTENTION This is a delicate operation, and prolonged contact between the grinding wheels

should be avoided, since this could damage them.

4. Turn the appliance o󰀨 by placing switch (13) on “0”.

5. Without moving the button (6), place the dial (4) on the “FINE” position then tighten the hexagon socket

screw (7) fully home.

6. Run the machine empty to check that the grinding wheels rotate without touching each other on the nest setting. If this is not the case, repeat the above procedure.

Troubleshooting

Identify the exact reason the appliance stopped.

In every case: If the problem persists, switch o󰀨 the power supply to the machine (unplug the cord from the mains socket) and call in the maintenance service or contact an Omcan approved dealer.

The machine will not start:

• Check: the mains power supply and the condition of the power supply cord.

• Note: the switch should be lit when on the “1” position.

• Check that there are no foreign bodies stuck between the grinding wheels.

The machine stops because the motor has overheated:

(the metal casing around the motor unit is hot)

In the event of overheating, the motor stops.

The overheating protection system resets automatically; wait for the motor to cool (15 to 30 minutes), before

restarting the machine.

8

Troubleshooting

The machine stops because of an overload:

If the motor is blocked (foreign body, something too hard), the excess current protection system (14), located under the appliance will be triggered automatically and cut o󰀨 the electrical power to the motor.

• Set the On / O󰀨 switch (13) to “0” position, disconnect the appliance.

• Correct the fault then press the excess current protection button (14).

• Press the On/O󰀨 switch (13) (position I).

If the problem persists, check the following points:

• Check that the grinding wheels do not touch each other.

• Check the state of wear of the grinding wheels (grinding too ne with worn grinding wheels can result in a motor overload like this).

• If there are no foreign bodies preventing the appliance from working, then check and replace the motor

starter relay then the capacitor.

9

Figure Drawings

10

Figure Drawings

11

Parts Breakdown

Model Santos 01PV 44116

12

Parts Breakdown

Model Santos 01PV 44116

Item No. Description Position Item No. Description Position Item No. Description Position

AC559

40662

63502 Hopper Cover for 01PV 01101 AC596 V Ring Gasket V20 for 01PV 01228 AC628 Screw H 4x10 for 01PV 01313

AC566 Hopper for 01PV 01102 AC597 Washer 5x20 for 01PV 01229 AC629 Bearing 6202 for 01PV 01314

40663 Obturator for 01PV 01103 AC598 Screw CHC 5x15 for 01PV 01230 AC630

AC567 Obturator Handle for 01PV 01104 AC599 Cap Nut H M6 for 01PV 01231 AC631

AC568 Screw CX 4x60 Zn for 01PV 01105 AC600 Washer Diam 6 for 01PV 01232 AC632 Screw 6x35 for 01PV 01317

AC569 Split Washer D 4 (Old) for 01PV 01106 AC601

AC570 Belleville Washer 5x12 for 01PV 01107 AC602 Barista Indexing Pointer for 01PV 01251 AC634 Washer 6x18x1 for 01PV 01319

AC571 Safety Bar for 01PV 01109 AC603 Screw CXS M4x12 Auto for 01PV 01252 AC635 Pin 3x5 for 01PV 01323

AC572

AC573

AC574 Adjusting Button for 01PV 01202 AC606 Ring D15 for 01PV 01255 AC638 Stainless Steel Motor Protector for 01PV 01337

AC575 Index for 01PV 01203 AC607 Barista Adjusting Button Spring for 01PV 01256 AC639 Motor Protector Spring for 01PV 01338

AC576 Graduated Round Plate for 01PV 01204 AC608 Barista Index Locking Screw for 01PV 01257 AC640 Ondulated Washer 6202 for 01PV 01340

AC577 Bearing Washer for 01PV 01205 AC609 Barista Graduated Ring for 01PV 01258 AC641

AC578 Bearing 6202 for 01PV 01206 AC610 Barista Soft Buttton for 01PV 01260 AC642

AC579 Steel Ball D 6 for 01PV 01207 AC611 Screw HC M8x10 for 01PV 01261 AC643

AC580 Adjusting Button Spring for 01PV 01208 AC612 Barista Adjusting Button for 01PV 01262 AC644

AC581 Screw HC M4x8 for 01PV 01209 AC613 Adjusting Ring for 01PV 01264 AC645

AC582 Screw H 4x8 Zn for 01PV 01210 AC614 O Ring 25x2.5 for 01PV 01265 AC646 Bottom Plate (Old) for 01PV 01403

AC583 Screw H 4x8 Zn for 01PV 01211 AC615 Barista Grind Housing for 01PV 01266 AC647 Washer AZ 4 ZN for 01PV 01404

AC584 Screw CB M5x35 Zn for 01PV 01212 AC616 Barista Complete Grind Housing for 01PV 01270 AC648 Rubber Foot D 25 for 01PV 01406

AC585 Grind Adjustment Screw for 01PV 01213 AC617

AC586 Grind Housing for 01PV 01214 AC618 Complete Front Flange (Brown) for 01PV 01301 AC650 Screw TCL 5.5x16 Zn for 01PV 01408

AC587 Washer AZ 5 for 01PV 01215 AC619 Front Flange Only (Brown) for 01PV 01302 AC651

AC588 Screw H 5x10 Zn for 01PV 01216 AC620 Bearing 6202 for 01PV 01303 AC652 Screw H 4.8x12.7 ZN for 01PV 01410

AC589 Screw CB M4x10 Zn for 01PV 01217 AC621 Bearing Washer (Thin) for 01PV 01304 AC653

AC590 Complete Grind Core for 01PV 01220 AC622 Screw M4x16 for 01PV 01305 AC654 Capacitor Ring D38 for 01PV 01413

AC591 Grind Core for 01PV 01221 AC623 Screw H M6x20 Zn for 01PV 01307 AC655 Capacitor Screw for 01PV 01414

AC592

AC593 Screw M4x10 for 01PV 01223 AC625 Complete Rear Flange for 01PV 01310 AC657 Switch (Old) for 01PV 01416

Set of 2 Special Poppy Seeds Discs Diam. 63.5 for 01PV

Complete Hopper with Obturator for 01PV

Complete Grind Housing (Poppy) for 01PV

Grind Housing with Adjusting Button for 01PV

Diameter 63.5 Grinding Disc (Poppy) for 01PV

00011 AC594 Complete Feeding Screw Poppy for 01PV 01225PV AC626 Rear Flange Only Brown for 01PV 01311

01100 AC595 Feeding Screw for 01PV 01226 AC627 Chromed Bearing Washer for 01PV 01312

Complete Stator (Winding) (Old<08/2017) for 01PV

Stator Only Single Phase 200-240V 50Hz (Old<08/2017) for 01PV

Bar Grind Housing with Adjusting Button for 01PV

01200PV AC604 Barista Grind Adjustment Screw for 01PV 01253 AC636

01201 AC605 Bearing Washer for 01PV 01254 AC637 Cap Nut H M5 for 01PV 01336

Complete Motor Single Phase 110V 60Hz (or 220V 60Hz) for 01PV

01222 AC624 Bearing Washer (Thick) for 01PV 01309 AC656 Nut H M4 Zn for 01PV 01415

01250 AC633 Nut H M6 Zn for 01PV 01318

Assembling Threaded Rod M5x134 for 01PV

Complete Rotor with Shaft - Single Phase and Pin for 01PV

Complete Stator (Winding) 110V 60Hz (or 220V 60Hz) for 01PV

Stator Only Single Phase 110V 60Hz (or 220V 60Hz) for 01PV

Complete Base - 1 Phase 110-120V 60 Hz for 01PV

Complete Bottom Plate 115V (Old) for 01PV

01300B AC649 Washer 5x12 for 01PV 01407

Starting Relay 100-120V 50/60Hz and 220V/60Hz for 01PV

Capacitor 250 MF 110 / 220V 60Hz for 01PV

01315

01316

01335

01360

01365B

01366B

01400B

01402B

01409B

01412B

13

Parts Breakdown

Model Santos 01PV 44116

Item No. Description Position Item No. Description Position Item No. Description Position

AC658 On-Off Plate (Old) for 01PV 01417 AC672 Bottom Plate for 01PV 01453 AC685 Screw TF M4x10 Zn for 01PV 01503

AC659 Power Cord with USA Plug for 01PV 01419B AC673

AC660 Screw H 4.2x12.7 ZN for 01PV 01422 AC674 Screw CXS M4x12 Auto for 01PV 01456 AC687 Bag Holder Sole for 01PV 01601

AC661

AC662 Cap D12.2x6.2 Black for 01PV 01436 AC676

AC663

AC664 Nut H M4 Zn for 01PV 01441 AC678 Barista On/Off Button for 01PV 01460 AC691 Rubber Buffer D12 H 7.5 for 01PV 01607

AC665 Washer AZ 4 ZN for 01PV 01442 AC679 Barista Complete Base 115V for 01PV 01470B AC692 Bag Holder Tube (Polished) for 01PV 01608

AC666 Screw CB M4x10 Zn for 01PV 01443 AC680 Barista Black Painted Base for 01PV 01471 AC693 SCREW FZ M3x6 for 01PV 01610

AC667 Screw H M5x12 Zn Autotar for 01PV 01445 AC681 Barista Bottom Plate 220V for 01PV 01472 AC694 Complete Poppy Outlet for 01PV 01700

AC668 Capacitor 150 µF Diam 46 for 01PV 01447 AC682 Circuit Breaker 8A (115V) for 01PV 01474B AC695 Ground Poppy Outlet Pipe for 01PV 01701

AC669 Capacitor Ring D46 for 01PV 01448 AC683

AC670 Painted Base for 01PV 01451 AC684 Drawer Sustainer Only for 01PV 01501 AC697 Barista Complete Poppy Outlet for 01PV 01770

AC671 Complete Bottom Plate 115V for 01PV 01452B 40664 Poppy Drawer for 01PV 01502 AC698

Special On-Off Multifunctions Switch 230V 8A115V for 01PV

Membrane + Plastic Tally Assembly for 01PV

01435B AC675 Barista Plate for 01PV 01457 AC688 Bakelite Ball for 01PV 01602

01437 AC677 Screw HC M6x8 for 01PV 01459 AC690 Complete Bag Holder Axle for 01PV 01604

Reversing Rotative Barista Switch for 01PV

Grooved Drive Stud 3x8 Stainless Steel for 01PV

Complete Drawer with Sustainer + Screws for 01PV

01455 AC686 Complete Bag Holder for 01PV 01600

01458 AC689 Bag Holder Spring for 01PV 01603

01500 AC696 Screw HM 4x16 Zn Auto for 01PV 01702

Barista Ground Poppy Outlet Pipe for 01PV

01771

14

Model Santos 01PV 44116

Electrical Schematics

15

Notes

________________________________________________________________________________________

16

Notes

________________________________________________________________________________________

17

Notes

________________________________________________________________________________________

18

Warranty Registration

Thank you for purchasing an Omcan product. To register your warranty for this product, complete the information below, tear o󰀨 the card at the perforation and then send to the address specied below. You can also register online by visiting:

Merci d’avoir acheté un produit Omcan. Pour enregistrer votre garantie pour ce produit, complétez les informations ci-dessous, détachez la carte au niveau de la perforation, puis l’envoyer à l’adresse spécié ci-dessous. Vous pouvez également vous inscrire en ligne en visitant:

Gracias por comprar un producto Omcan usted. Para registrar su garantía para este producto, complete la información a continuación, cortar la tarjeta en la perforación y luego enviarlo a la dirección indicada a continuación. También puede registrarse en línea en:

https://omcan.com/warranty-registration/

For mailing in Canada

Pour postale au Canada

Por correo en Canadá

OMCAN

PRODUCT WARRANTY REGISTRATION

3115 Pepper Mill Court,

Mississauga, Ontario

Canada, L5L 4X5

PRODUCT WARRANTY REGISTRATION

4450 Witmer Industrial Estates, Unit 4,

For mailing in the US

Pour di󰀨usion aux États-Unis

Por correo en los EE.UU.

OMCAN

Niagara Falls, New York

USA, 14305

or email to: service@omcan.com



Purchaser’s Information

Name: Company Name:

Address:

Telephone:

City: Province or State: Postal or Zip: Email Address:

Country: Type of Company:

Restaurant Bakery Deli

Dealer from which Purchased: Butcher Supermarket Caterer

Dealer City: Dealer Province or State: Institution (specify):

Invoice: Other (specify):

Model Name: Model Number: Serial Number:

Machine Description:

Date of Purchase (MM/DD/YYYY): Date of Installation (MM/DD/YYYY):

Would you like to extend the warranty? Yes No

Thank you for choosing Omcan | Merci d’avoir choisi Omcan | Gracias por elegir Omcan

19

Since 1951 Omcan has grown to become a leading distributor of equipment and supplies to the North American food service industry. Our success over these many years can be attributed to our commitment to strengthen and develop new and existing relationships with our valued customers and manufacturers. Today with partners in North America, Europe, Asia and South America, we continually work to improve

and grow the company. We strive to offer customers exceptional value through our qualied local sales

and service representatives who provide convenient access to over 5,000 globally sourced products.

Depuis 1951 Omcan a grandi pour devenir un des “leaders” de la distribution des équipements et matériel pour l’industrie des services alimentaires en Amérique du Nord. Notre succès au cours de ces nombreuses années peut être attribué à notre engagement à renforcer et à développer de nouvelles et existantes relations avec nos clients et les fabricants de valeur. Aujourd’hui avec des partenaires en Amérique du Nord, Europe, Asie et Amérique du Sud, nous travaillons continuellement à améliorer et développer l’entreprise. Nous nous efforçons d’offrir à nos clients une valeur exceptionnelle grâce à

nos ventes locales qualiées et des représentants de service qui offrent un accès facile à plus de 5000

produits provenant du monde entier.

Desde 1951 Omcan ha crecido hasta convertirse en un líder en la distribución de equipos y suministros de alimentos en América del Norte industria de servicios. Nuestro éxito en estos años se puede atribuir a nuestro compromiso de fortalecer y desarrollar nuevas relaciones existentes con nuestros valiosos clientes y fabricantes. Hoy con socios de América del Norte, Europa, Asia y América del Sur, que trabajan continuamente para mejorar y crecer la empresa. Nos esforzamos por ofrecer a nuestros clientes valor excepcional a través de nuestro local de ventas y representantes de los servicios que proporcionan un fácil acceso a más de 5,000 productos con origen a nivel mundial.

Omcan SANTOS 01PV Operators Manual

Specifications and Main Features

Frequently Asked Questions

User Manual