Refrigerated Showcases
Models RS-CN-0120-B, 0200-B, 0120-S, 0200-S
Items 50077, 50078, 50079, 50080
Instruction Manual
Revised - 09/25/2018
Toll Free: 1-800-465-0234
Fax: 905-607-0234
Email: service@omcan.com
www.omcan.com
Table of Contents
Model RS-CN-0120-B / Model RS-CN-0200-B
Model RS-CN-0120-S / Model RS-CN-0200-S
Section
General Information
Safety and Warranty
Technical Specications
Installation and Operation
Maintenance
Troubleshooting
------------------------------------------------------------------------------------ 7 - 9
--------------------------------------------------------------------------- 3 - 4
--------------------------------------------------------------------------- 4 - 5
------------------------------------------------------------------------------- 9 - 10
Page
-------------------------------------------------------------------------- 6
-------------------------------------------------------------------- 6 - 7
Parts Breakdown
Electrical Schematics
Notes
Warranty Registration
------------------------------------------------------------------------------------------------ 18
---------------------------------------------------------------------------- 11 - 16
---------------------------------------------------------------------------- 17
---------------------------------------------------------------------------- 19
2
General Information
Omcan Manufacturing and Distributing Company Inc., Food Machinery of America, Inc. dba Omcan
and Omcan Inc. are not responsible for any harm or injury caused due to any person’s improper or
negligent use of this equipment. The product shall only be operated by someone over the age of 18, of
sound mind, and not under the inuence of any drugs or alcohol, who has been trained in the correct
operation of this machine, and is wearing authorized, proper safety clothing. Any modication to the
machine voids any warranty, and may cause harm to individuals using the machine or in the vicinity of
the machine while in operation.
CHECK PACKAGE UPON ARRIVAL
Upon receipt of an Omcan shipment please inspect for external damage. If no damage is evident on the
external packaging, open carton to ensure all ordered items are within the box, and there is no concealed
damage to the machine. If the package has suered rough handling, bumps or damage (visible or concealed),
please note it on the bill of lading before accepting the delivery and contact Omcan within 24 hours, so we may
initiate a claim with the carrier. A detailed report on the extent of the damage caused to the machine must be
lled out within three days, from the delivery date shown in the shipping documents. Omcan has no recourse
for damaged products that were shipped collect or third party.
Before operating any equipment, always read and familiarize yourself with all operation and safety
instructions.
Omcan would like to thank you for purchasing this machine. It’s of the utmost importance to save
these instructions for future reference. Also save the original box and packaging for shipping the
equipment if servicing or returning of the machine is required.
--------------------------------------------------------------------------------------------------------------------------------------------------Omcan Fabrication et distribution Companie Limité et Food Machinery d’Amerique, dba Omcan et
Omcan Inc. ne sont pas responsables de tout dommage ou blessure causé du fait que toute personne
ait utilisé cet équipement de façon irrégulière. Le produit ne doit être exploité que par quelqu’un de
plus de 18 ans, saine d’esprit, et pas sous l’inuence d’une drogue ou d’acohol, qui a été formé pour
utiliser cette machine correctement, et est vêtu de vêtements de sécurité approprié. Toute modication
de la machine annule toute garantie, et peut causer un préjudice à des personnes utilisant la machine
ou des personnes à proximité de la machine pendant son fonctionnement.
VÉRIFIEZ LE COLIS DÈS RÉCEPTION
Dès réception d’une expédition d’Omcan veuillez inspecter pour dommages externes. Si aucun dommage
n’est visible sur l’emballage externe, ouvrez le carton an de s’assurer que tous les éléments commandés
sont dans la boîte, et il n’y a aucun dommage dissimulé à la machine. Si le colis n’a subi aucune mauvaises
manipulations, de bosses ou de dommages (visible ou cachée), notez-le sur le bond de livraison avant
d’accepter la livraison et contactez Omcan dans les 24 heures qui suivent, pour que nous puissions engager
une réclamation auprès du transporteur. Un rapport détaillé sur l’étendue des dommages causés à la machine
doit être rempli dans un délai de trois jours, à compter de la date de livraison indiquée dans les documents
d’expédition. Omcan n’a aucun droit de recours pour les produits endommagés qui ont été expédiées ou cueilli
par un tiers transporteur.
3
General Information
Avant d’utiliser n’importe quel équipement, toujours lire et vous familiariser avec toutes les opérations
et les consignes de sécurité.
Omcan voudrais vous remercier d’avoir choisi cette machine. Il est primordial de conserver ces
instructions pour une référence ultérieure. Également conservez la boîte originale et l’emballage pour
l’expédition de l’équipement si l’entretien ou le retour de la machine est nécessaire.
--------------------------------------------------------------------------------------------------------------------------------------------------Omcan Empresa De Fabricacion Y Distribucion Inc. Y Maquinaria De Alimentos De America, Inc. dba
Omcan y Omcan Inc. no son responsables de ningun daño o perjuicío causado por cualquier persona
inadecuada o el uso descuidado de este equipo. El producto solo podra ser operado por una persona
mayor de 18 años, en su sano juicio y no bajo alguna inuencia de droga o alcohol, y que este ha sido
entrenado en el correcto funcionamiento de esta máquina, y ésta usando ropa apropiada y autorizada.
Cualquier modicación a la máquina anúla la garantía y puede causar daños a las personas usando la
máquina mientras esta en el funcionamiento.
REVISE EL PAQUETE A SU LLEGADA
Tras la recepcion de un envio Omcan favor inspeccionar daños externos. Si no hay daños evidentes en el
empaque exterior, Habra el carton para asegurararse que todos los articulos solicitados ésten dentro de la
caja y no encuentre daños ocultos en la máquina. Si el paquete ha sufrido un manejo de poco cuidado, golpes
o daños (visible o oculto) por favor anote en la factura antes de aceptar la entrega y contacte Omcan dentro
de las 24 horas, de modo que podamos iniciar una reclamación con la compañia. Un informe detallado sobre
los daños causados a la máquina debe ser llenado en el plazo de tres días, desde la fecha de entrega que se
muestra en los documentos de envío. Omcan no tiene ningun recurso por productos dañados que se enviaron
a recoger por terceros.
Antes de utilizar cualquier equipo, siempre leer y familiarizarse con todas las instrucciones de
operación y seguridad.
Omcan quisiera darles las gracias por la compra de esta máquina. Es de la máxima importancia para
guardar estas instrucciones para referencias en el futuro. También guarde la caja original y el embalaje
para envío del equipo si el mantenimiento o la devolución de la máquina es necesaria.
Safety and Warranty
WHEN USING ELECTRICAL APPLIANCES BASIC SAFETY PRECAUTIONS SHOULD BE FOLLOWED:
• This cooler must be properly installed and located in accordance with the installation service
representative.
• Do not allow children to climb, stand or hang on the shelves in the cooler. They could damage the unit and
seriously injure themselves.
• Do not store or use gasoline or other ammable vapors and liquids in the vicinity of this or any other
appliance.
4
Safety and Warranty
• Unplug the unit from the electrical outlet before cleaning or making repairs.
• Do not touch the cold surfaces in the refrigerator compartment when hands are damp or wet. Skin may
stick to these extremely cold surfaces.
NOTE: It is strongly recommended that any servicing be performed by an authorized instructions
before it is used.
• When the refrigerator is installed or used,all the packaging (including cardboard and plastic wrap)should be
removed.
• Keep the refrigerator stable to avoid vibration and noise.
• The refrigerator should be installed in a place with good ventilation and a space of at least 4” should be
allowed between the surrounding walls and the cabinet wall for air circulation.
• Unit should be placed far from any heating source to avoid decrease of refrigeration eciency.
• Install the refrigerator in a dry place to prevent rust from forming on the compartment body, which may
aect the electrical insulation.
1 YEAR PARTS AND LABOR WARRANTY
Within the warranty period, contact Omcan Inc. at 1-800-465-0234 to schedule an Omcan authorized
service technician to repair the equipment locally.
Unauthorized maintenance will void the warranty. Warranty covers electrical and part failures, not
improper use.
Please see www.omcan.com/warranty.html for complete info.
WARNING:
The packaging components are classied as normal solid urban waste and can therefore be disposed of
without diculty.
In any case, for suitable recycling, we suggest disposing of the products separately (dierentiated
waste) according to the current norms.
DO NOT DISCARD ANY PACKAGING MATERIALS IN THE ENVIRONMENT!
5
Technical Specications
Model RS-CN-0120-B RS-CN-0200-B RS-CN-0120-S RS-CN-0200-S
Material Black Coated Steel Stainless Steel
Temperature Range 32 - 43°F / 0 - 6°C
Number of Doors 2 3 2 3
Number of Shelves 6 9 6 9
Capacity 508 L / 18 cu. ft. 903 L / 32 cu. ft. 508 L / 18 cu. ft. 903 L / 32 cu. ft.
HP 1/4+ 3/4 1/4+ 3/4
Current 2.6A 5.9A 2.6A 5.9A
Electrical 115V / 60Hz / 1
Refrigerant R290
Dimensions
Item Number 50077 50078 50079 50080
47.3” x 32.5” x 42.9”
1200 x 825 x 1089mm
78.8” x 32.5” x 42.9”
2000 x 825 x 1089mm
47.3” x 32.5” x 42.9”
1200 x 825 x 1089mm
78.8” x 32.5” x 42.9”
2000 x 825 x 1089mm
Installation and Operation
To ensure that your unit works properly from the rst day, it must be installed properly. We highly recommend a
trained refrigeration mechanic and electrician install your equipment.
• Remove the outer packaging, Inspect for concealed damage. Again, immediately le a claim with the freight
carrier if there is damage.
• Remove the wood frame and pallet.
• Place the refrigerator on a at surface and remove to the nal location. Be sure there is adequate
ventilation in your room. Under extreme heat conditions, (100°F+, 38°C+), you may want to install an
exhaust fan.
ELECTRICAL
Do not under any circumstances cut or remove the grounding prong from the power cord. For safety this
appliance must be properly grounded at all times.
• The power cord of this cooler is equipped with a grounding plug which mates with a standard grounding
wall outlet to minimize the possibility of electric shock hazard.
• If the outlet is a standard 2-prong outlet, it must be replaced with the properly grounded wall outlet. NEVER
USE AN ADAPTER PLUG!
• Have the wall outlet and circuit checked by a qualied electrician to make sure the outlet is properly
grounded. Check the incoming voltage with a voltmeter.
• DO NOT USE EXTENSION CORDS. The use of extension cords to connect the cooler will void warranty.
The unit must be close enough to the electrical supply so that extension cords are never used.
• The cooler should always be plugged into its own dedicated circuit with a voltage rating that matches the
rating plate. This provides the best performance and also prevents overloading wiring circuits which could
become a re hazard from overheated wires.
6
Installation and Operation
• Never unplug your cooler by pulling on the power cord. Always grip the plug rmly and pull straight out from
the outlet.
• Repair or replace immediately all power cords that have become frayed or otherwise damaged. Do not use
a power cord that has cracks or abrasion damage along its length or at either of its ends.
• When removing the cooler away from the wall be careful not to run over or damage the power cord.
NOTE: Wiring diagram can be referenced by removing the front louvered grill, and looking on the
inside cabinet wall.
PLUG IN THE COOLER AND THE COMPRESSOR IS READY TO OPERATE.
• Excessive tampering with the control could lead to service diculties. Should it ever become necessary to
replace the temperature control it should be ordered from your dealer or recommended service agent.
LIGHT SWITCH LOCATION:
The light switch is located at the left side of rear grille.
NOTE: If the unit is disconnected or shut o, wait ve (5) minutes before re-starting unit.
RECOMMENDATION: Before loading product the unit should be run for 2 to 3 hours. This allows
conrmation that the electrical wiring and installation are correct and no shipping damage has
occurred.
Maintenance
Condensers accumulate dirt and dust and require cleaning every 30 days. Dirty condensers result in
compressor failure, product loss, and lost sales -- which are not covered by warranty.
Air is pulled through the condenser continuously along with dust, lint, grease, etc. If you keep the condenser
clean you will minimize your service expense and lower your electrical costs. The condenser requires
scheduled cleaning every days or as needed. A dirty condenser can result in non-warranted part and
compressor failures and product loss.
Proper cleaning involves removing debris from the condenser by using a soft brush or vacuuming the
condenser with a shop vacuum or using CO2, nitrogen or pressurized air.
If you cannot remove the debris adequately please call you refrigeration service company.
CLEANING THE CONDENSER COIL
REQUIRED TOOLS
• Phillips screwdriver.
• Sti bristle brush.
• Adjustable wrench.
7
Maintenance
WHEN USING ELECTRICAL APPLIANCES BASIC SAFETY PRECAUTIONS SHOULD BE FOLLOWED.
• Disconnect power to unit.
• Take o front grill assembly by removing all screws.
• Remove bolts anchoring compressor assembly to frame rails and carefully slide out --tube connections are
exible.
• Clean o accumulated dirt from condensing coil with the sti bristle brush.
• Lift cardboard cover above fan at plastic plugs and carefully clean condenser coil and fan blades.
• After brushing condenser coil, vacuum dirt from coil and interior oor.
• Replace cardboard cover, carefully slide compressor assembly back into position and replace bolts.
• Reinstall front grille assembly onto unit with appropriate fasteners and clips. Tighten all screws.
• Connect unit to power and check to see if condenser is running.
STAINLESS STEEL CARE AND CLEANING
RECOMMENDED CLEANERS FOR STAINLESS STEEL
• Soap, ammonia and detergent medallion applied with a soft cloth or sponge for routine cleaning.
• Arcal 20, Loc-O-Nu Eco shine provide a barrier lm for ngerprints and smears.
• Cameo,Talc,Z ud First Impression is for stubborn stains and discoloration. Rub in direction of polish lines.
• Easy-o and De-Grease It oven aid are excellent for removals on all nishes for grease-fatty acids,blood
and burnt-on foods.
• Any good commercial detergent can be applied with a sponge or soft cloth to remove grease and oil.
• Benet,Super Sheen,Sheila Shine are good for restoration/passiveness.
CAUTION: Do not use any steel wool, abrasive or chlorine based products to clean stainless steel
surfaces.
STAINLESS STEEL ENEMIES
There are three basic items that can break down stainless steel’s passivity layer and allow corrosion to occur.
• Scratches from wire brushes, metal scrapers and steel pads are just a few examples of items that can be
abrasive to stainless steel’s surface.
• Deposits left on stainless steel can leave spots. Hard water can leave spots. Hard water that is heated can
leave deposits if left to sit for too long. These deposits can cause the passive layer to break down and rust
stainless steel. All deposits left from food prep or service should be removed as quickly as possible.
• Chlorides are present in table salt, food and water. Household and industrial cleaners are the worst type of
chlorides to use.
8 STEPS THAT CAN HELP PREVENT RUST ON STAINLESS STEEL
• Use the correct cleaning tools. Use non-abrasive tools when cleaning your stainless steel products. The
stainless steel’s passive layer will not be harmed by soft cloths and plastic scouring pads.
• Clean along the polish lines. Polish lines or grain are visible on some stainless steel. Always scrub parallel
to visible lines. Use a plastic scouring pad or soft cloth when grain is not visible.
• Use alkaline, alkaline chlorinated or non-chloride containing cleaners. While many traditional cleaners are
loaded with chlorides, the industry is providing an ever increasing choice of non-chloride cleaners. If unsure
of chloride content contact the cleaner supplier. If present cleaner contains chlorides, ask for an alternative.
Avoid cleaners containing quaternary salts as they can attack stainless steel causing pitting and rusting.
8
Maintenance
• Water treatment. To reduce deposits, use soft water whenever possible. Installation of certain lters can be
an advantage. Contact a treatment specialist about proper water treatment.
• Maintain cleanliness of food equipment. Use cleaners at recommended strength(alkaline, alkaline
chlorinated or non-chloride). Avoid buildup of hard stains by cleaning frequently.
• When using chlorinated cleaners you must rinse and wipe dry immediately. It is better to wipe standing
cleaning agents and water as soon as possible. All stainless steel equipment to air dry. Oxygen helps
maintain the passivity lm on stainless steel.
• Hydrochloric acid (muriatic acid) should never be used on stainless steel.
• Regularly restore/passiveness stainless steel.
Troubleshooting
Before requesting any service on your unit, please check the following points. Please note that this guide
serves only as a reference for solutions to common problems.
SYMPTOM POSSIBLE CAUSE CORRECTIVE ACTION
Compressor not running. Fuse blown or circuit breaker
tripped.
Power cord unplugged. Plug in power cord.
Thermostat set too high. Set thermostat to lower
Cabinet in defrost cycle. Wait for defrost cycle to nish.
Condensing unit runs for long
periods of time.
Excessive amount of warn product
placed in cabinet.
Prolonged door opening or door
ajar.
Door gasket(s) not sealing
properly.
Dirty condenser coil. Clean the condenser coil.
Evaporator coil iced over. Unplug unit and allow coil to
Replace fuse or reset circuit
breaker.
temperature.
Allow adequate time for product to
cool down.
Ensure doors are closed when not
in use. Avoid opening doors for
long periods of time.
Ensure gaskets are snapped in
completely. Remove gasket and
wash with soap and water. Check
condition of gasket and replace if
necessary.
defrost. Make sure thermostat is
not set too cold. Ensure that door
gasket(s) are sealing properly.
9
Troubleshooting
Cabinet temperature is too warm. Thermostat set too warm. Set thermostat to lower
temperature.
Blocking air ow. Re-arrange product to allow for
proper air ow. Make sure there is
at least four inches of clearance
from evaporator.
Excessive amount of warm product
placed in cabinet.
Fuse blown or circuit breaker
tripped.
Dirty condenser coil. Clean the condenser coil.
Prolonged door opening or door
ajar.
Evaporator coil iced over. Unplug unit and allow coil to
Cabinet is noisy. Loose part(s). Locate and tighten loose part(s).
Tubing vibration. Ensure tubing is free from contact
Allow adequate time for product to
cool down.
Replace fuse or reset circuit
breaker.
Ensure doors are closed when not
in use. Avoid opening doors for
long periods of time.
defrost. Make sure thermostat is
not set too cold. Ensure that door
gasket(s) are sealing properly.
with other tubing or components.
REFERENCE
Item Number Model Number Description
Refrigerated Showcase Floor Black
50077 RS-CN-0120-B
50078 RS-CN-0200-B
Refrigerated Showcase Floor Stainless
50079 RS-CN-0120-S
Refrigerated Showcase Floor Stainless
50080 RS-CN-0200-S
508 L / 18 cu ft 115V/60/1
cETLus/ETL
Refrigerated Showcase Floor Black
903 L / 32 cu ft 115V/60/1
cETLus/ETL
Steel 508 L / 18 cu ft 115V/60/1
cETLus/ETL
Steel 903 L / 32 cu ft 115V/60/1
cETLus/ETL
Manufacturer Model
Number
DC120-HC-BK
DC200-HC-BK
DC120-HC-SS
DC200-HC-SS
10
Model RS-CN-0120-B 50077
Model RS-CN-0120-S 50079
Parts Breakdown
11
Parts Breakdown
Model RS-CN-0120-B 50077
Item No. Description Position Item No. Description Position Item No. Description Position
64201
64202
26233
26184
62357
64203
64204
64205 Front Grill Black for DC120-HC-BK 8 62322 Power Cord (16 AWG) for DC120-HC-BK 26 64232
64206
64207 Curve Glass for DC120-HC-BK 10 64222 Right Bracket for DC120-HC-BK 28 64234
64208 Socket of LED Lamp for DC120-HC-BK 11 64223 Middle Bracket for DC120-HC-BK 29 64235 Cabinet for DC120-HC-BK 47
64209 LED Light (1m) for DC120-HC-BK 12 64224
64210 Bottom Shelf for DC120-HC-BK 13 64225 Left Bracket for DC120-HC-BK 31 64237
64211
64212
64213 Upper Shelf for DC120-HC-BK 16 64228
64214
64215 Right Hanger of Grill for DC120-HC-BK 18 64230 Inner Drain Pipe for DC120-HC-BK 36 67555 Display Cover Board for DC120-HC-BK 54
Right Track of Installation Board for
DC120-HC-BK
Installation Board of Compressor for
DC120-HC-BK
Blade of Condenser Fan Motor (φ230
V34) for DC120-HC-BK
Condenser (3R10K260L) for DC120-
HC-BK
Adjustable Feet (M12x45) for DC120-
HC-BK
Support Board of Adjustable Feet for
DC120-HC-BK
Limited Block of Installation Board for
DC120-HC-BK
Fixed Board of Curve Glass for DC120HC-BK
Connection Board of Shelf Support Board
for DC120-HC-BK
Right Shelf Support Board for DC120HC-BK
Left Shelf Support Board for DC120HC-BK
1 64216 Grill Components for DC120-HC-BK 19 26670 Compressor for DC120-HC-BK 37
2 64217
3 64218 Digital Thermostat for DC120-HC-BK 21 62036 Filter for DC120-HC-BK 39
4 26192 Lamp Switch (Red) for DC120-HC-BK 22 26188 Filter Base for DC120-HC-BK 40
5 64219
6 64220 Inner Drain Pipe for DC120-HC-BK 24 24293
7 64221
9 26539
14 64226 Glass Door for DC120-HC-BK 32 64238 Left Hanger of Grill for DC120-HC-BK 50
15 64227
17 64229 Outer Drain Pan for DC120-HC-BK 35 67554 Defroster for DC120-HC-BK 53
Evaporator (2R6K850L φ12.7) for
DC120-HC-BK
Temperature Sensor Clip for DC120HC-BK
Waterproof Cover of Thermostat for
DC120-HC-BK
Digital Thermostat Installation Box for
DC120-HC-BK
Air Pipe Protection Board for DC120HC-BK
Plastic Connector of Drain Pipe for
DC120-HC-BK
Coiled Copper Pipe of Outer Drain Pan
for DC120-HC-BK
20 62318
23 26233
25 64231
27 64233
30
33 64239 Sealing Rubber Strip for DC120-HC-BK 51
34 67553
64236 Large Back Grill for DC120-HC-BK 48
Compressor Components for DC120HC-BK
Cover of Condenser Fan Motor for
DC120-HC-BK
Condenser Fan Motor (M4Q045-
CF07-04) for DC120-HC-BK
Left Track of Installation Board for
DC120-HC-BK
Cover Board of Machine Room for
DC120-HC-BK
Support Holder of Cabinet for DC120HC-BK
Cover Board of Machine Room for
DC120-HC-BK
Framework of Door Track for DC120HC-BK
Evaporator Cover Panel for DC120HC-BK
38
41
42
43
44
45
46
49
52
12
Parts Breakdown
Model RS-CN-0120-S 50079
Item No. Description Position Item No. Description Position Item No. Description Position
64201
64202
26233
26184
62357
64203
64204
66996
64206
64207 Curve Glass for DC120-HC-SS 10 64222 Right Bracket for DC120-HC-SS 28 64234
64208 Socket of LED Lamp for DC120-HC-SS 11 64223 Middle Bracket for DC120-HC-SS 29 64235 Cabinet for DC120-HC-SS 47
64209 LED Light (1m) for DC120-HC-SS 12 64224
64210 Bottom Shelf for DC120-HC-SS 13 64225 Left Bracket for DC120-HC-SS 31 64237
64211
64212
64213 Upper Shelf for DC120-HC-SS 16 64228
64214
64215 Right Hanger of Grill for DC120-HC-SS 18 64230 Inner Drain Pipe for DC120-HC-SS 36 67555 Display Cover Board for DC120-HC-SS 54
Right Track of Installation Board for
DC120-HC-SS
Installation Board of Compressor for
DC120-HC-SS
Blade of Condenser Fan Motor (φ230
V34) for DC120-HC-SS
Condenser (3R10K260L) for DC120-
HC-SS
Adjustable Feet (M12x45) for DC120-
HC-SS
Support Board of Adjustable Feet for
DC120-HC-SS
Limited Block of Installation Board for
DC120-HC-SS
Front Grill Stainless Steel for DC120HC-SS
Fixed Board of Curve Glass for DC120HC-SS
Connection Board of Shelf Support Board
for DC120-HC-SS
Right Shelf Support Board for DC120HC-SS
Left Shelf Support Board for DC120HC-SS
1 64216 Grill Components for DC120-HC-SS 19 26670 Compressor for DC120-HC-SS 37
2 64217
3 64218 Digital Thermostat for DC120-HC-SS 21 62036 Filter for DC120-HC-SS 39
4 26192 Lamp Switch (Red) for DC120-HC-SS 22 26188 Filter Base for DC120-HC-SS 40
5 64219
6 64220 Inner Drain Pipe for DC120-HC-SS 24 24293
7 64221
8 62322 Power Cord (16 AWG) for DC120-HC-SS 26 64232
9 26539
14 64226 Glass Door for DC120-HC-SS 32 64238 Left Hanger of Grill for DC120-HC-SS 50
15 64227
17 64229 Outer Drain Pan for DC120-HC-SS 35 67554 Defroster for DC120-HC-SS 53
Evaporator (2R6K850L φ12.7) for
DC120-HC-SS
Temperature Sensor Clip for DC120HC-SS
Waterproof Cover of Thermostat for
DC120-HC-SS
Digital Thermostat Installation Box for
DC120-HC-SS
Air Pipe Protection Board for DC120HC-SS
Plastic Connector of Drain Pipe for
DC120-HC-SS
Coiled Copper Pipe of Outer Drain Pan
for DC120-HC-SS
20 62318
23 26233
25 64231
27 64233
30 64236 Large Back Grill for DC120-HC-SS 48
33 64239 Sealing Rubber Strip for DC120-HC-SS 51
34 67553
Compressor Components for DC120HC-SS
Cover of Condenser Fan Motor for
DC120-HC-SS
Condenser Fan Motor (M4Q045-
CF07-04) for DC120-HC-SS
Left Track of Installation Board for
DC120-HC-SS
Cover Board of Machine Room for
DC120-HC-SS
Support Holder of Cabinet for DC120HC-SS
Cover Board of Machine Room for
DC120-HC-SS
Framework of Door Track for DC120HC-SS
Evaporator Cover Panel for DC120HC-SS
38
41
42
43
44
45
46
49
52
13
Parts Breakdown
Model RS-CN-0200-B 50078
Model RS-CN-0200-S 50080
14
Parts Breakdown
Model RS-CN-0200-B 50078
Item No. Description Position Item No. Description Position Item No. Description Position
64201
64202
26233
26231
62357
64203
64204
64240 Front Grill Black for DC200-HC-BK 8 64233
64241
64242 Curve Glass for DC200-HC-BK 10 64247 Left Hinge of Grill for DC200-HC-BK 28 64231
64208 Socket of LED Lamp for DC200-HC-BK 11 26539
64209 LED Light for DC200-HC-BK 12 64220 Inner Drain Pipe for DC200-HC-BK 30 64250
64243 Bottom Shelf for DC200-HC-BK 13 64225 Left Bracket for DC200-HC-BK 31 64251
64244
64212
64207 Upper Shelf for DC200-HC-BK 16 64224
64213
64215 Right Hanger of Grill for DC200-HC-BK 18 64249
Right Track of Installation Board for
DC200-HC-BK
Installation Board of Compressor for
DC200-HC-BK
Blade of Condenser Fan Motor (φ230
V34) for DC200-HC-BK
Condenser (4R10K260L) for DC200-
HC-BK
Adjustable Feet (M12x45) for DC200-
HC-BK
Support Board of Adjustable Feet for
DC200-HC-BK
Limited Block of Installation Board for
DC200-HC-BK
Fixed Board of Curve Glass for DC200HC-BK
Connection Board of Shelf Support Board
for DC200-HC-BK
Right Shelf Support Board for DC200HC-BK
Left Shelf Support Board for DC200HC-BK
1 64245 Grill Components for DC200-HC-BK 19 64228
2 64246
3 62322 Power Cord (16 AWG) for DC200-HC-BK 21 64230 Inner Drain Pan for DC200-HC-BK 39
4 64227
5 64219
6 26192 Lamp Switch (Red) for DC200-HC-BK 24 26188 Filter Base for DC200-HC-BK 42
7 64218 Digital Thermostat for DC200-HC-BK 25 62036 Filter for DC200-HC-BK 43
9 64239 Sealing Rubber Strip for DC200-HC-BK 27 26330
14 64223 Middle Bracket for DC200-HC-BK 32 64233 Cabinet Support for DC200-HC-BK 50
15 64222 Right Bracket for DC200-HC-BK 33 64252 Right Back Grill for DC200-HC-BK 51
17 64248 Glass Door for DC200-HC-BK 35 67556
Evaporator (2R6K1700L φ12.7) for
DC200-HC-BK
Plastic Connector of Drain Pipe for
DC200-HC-BK
Temperature Sensor Clip for DC200HC-BK
Waterproof of Thermostat for DC200HC-BK
Digital Thermostat Installation Box for
DC200-HC-BK
Air Pipe Protection Board for DC200HC-BK
Framework of Glass Door for DC200HC-BK
20 64229 Outer Drain Pan for DC200-HC-BK 38
22 26280 Compressor for DC200-HC-BK 40
23 61473
26 26282
29 64232
34 64236 Back Grill for DC200-HC-BK 52
36 67557 Defroster for DC200-HC-BK 54
Coiled Copper Pipe of Outer Drain Pan
for DC200-HC-BK
Compressor Components for DC200HC-BK
Condenser Fan Motor (M4Q045-
CF07-04) for DC200-HC-BK
Condenser Fan Motor Cover for DC200HC-BK
Left Track of Installation Board for
DC200-HC-BK
Cover Board of Machine Room (Small)
for DC200-HC-BK
Support Board of Machine Room for
DC200-HC-BK
Cover Board of Machine Room (Big) for
DC200-HC-BK
Evaporator Cover Panel for DC200HC-BK
37
41
44
45
46
47
48
49
53
15
Parts Breakdown
Model RS-CN-0200-S 50080
Item No. Description Position Item No. Description Position Item No. Description Position
64201
64202
26233
26231
62357
64203
64204
66997
64241
64242 Curve Glass for DC200-HC-SS 10 64247 Left Hinge of Grill for DC200-HC-SS 28 64231
64208 Socket of LED Lamp for DC200-HC-SS 11 26539
64209 LED Light for DC200-HC-SS 12 64220 Inner Drain Pipe for DC200-HC-SS 30
64243 Bottom Shelf for DC200-HC-SS 13 64225 Left Bracket for DC200-HC-SS 31 64251
64244
64212
64207 Upper Shelf for DC200-HC-SS 16 64224
64213
64215 Right Hanger of Grill for DC200-HC-SS 18 64249
Right Track of Installation Board for
DC200-HC-SS
Installation Board of Compressor for
DC200-HC-SS
Blade of Condenser Fan Motor (φ230
V34) for DC200-HC-SS
Condenser (4R10K260L) for DC200-
HC-SS
Adjustable Feet (M12x45) for DC200-
HC-SS
Support Board of Adjustable Feet for
DC200-HC-SS
Limited Block of Installation Board for
DC200-HC-SS
Front Grill Stainless Steel for DC200HC-SS
Fixed Board of Curve Glass for DC200HC-SS
Connection Board of Shelf Support Board
for DC200-HC-SS
Right Shelf Support Board for DC200HC-SS
Left Shelf Support Board for DC200HC-SS
1 64245 Grill Components for DC200-HC-SS 19 64228
2 64246
3 62322 Power Cord (16 AWG) for DC200-HC-SS 21 64230 Inner Drain Pan for DC200-HC-SS 39
4 64227
5 64219
6 26192 Lamp Switch (Red) for DC200-HC-SS 24 26188 Filter Base for DC200-HC-SS 42
7 64218 Digital Thermostat for DC200-HC-SS 25 62036 Filter for DC200-HC-SS 43
8 64233
9 64239 Sealing Rubber Strip for DC200-HC-SS 27 26330
14 64223 Middle Bracket for DC200-HC-SS 32 64233 Cabinet Support for DC200-HC-SS 50
15 64222 Right Bracket for DC200-HC-SS 33 64252 Right Back Grill for DC200-HC-SS 51
17 64248 Glass Door for DC200-HC-SS 35 67556
Evaporator (2R6K1700L φ12.7) for
DC200-HC-SS
Plastic Connector of Drain Pipe for
DC200-HC-SS
Temperature Sensor Clip for DC200HC-SS
Waterproof of Thermostat for DC200HC-SS
Digital Thermostat Installation Box for
DC200-HC-SS
Air Pipe Protection Board for DC200HC-SS
Framework of Glass Door for DC200HC-SS
20 64229 Outer Drain Pan for DC200-HC-SS 38
22 26280 Compressor for DC200-HC-SS 40
23 61473
26 26282
29 64232
64250
34 64236 Back Grill for DC200-HC-SS 52
36 67557 Defroster for DC200-HC-SS 54
Coiled Copper Pipe of Outer Drain Pan
for DC200-HC-SS
Compressor Components for DC200HC-SS
Condenser Fan Motor (M4Q045-
CF07-04) for DC200-HC-SS
Condenser Fan Motor Cover for DC200HC-SS
Left Track of Installation Board for
DC200-HC-SS
Cover Board of Machine Room (Small)
for DC200-HC-SS
Support Board of Machine Room for
DC200-HC-SS
Cover Board of Machine Room (Big) for
DC200-HC-SS
Evaporator Cover Panel for DC200HC-SS
37
41
44
45
46
47
48
49
53
16
Model RS-CN-0120-B 50077
Model RS-CN-0200-B 50078
Model RS-CN-0120-S 50079
Model RS-CN-0200-S 50080
Electrical Schematics
17
Notes
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
________________________________________________________________________________________
18
Warranty Registration
Thank you for purchasing an Omcan product. To register your warranty for this product, complete the information below, tear o the card at
the perforation and then send to the address specied below. You can also register online by visiting:
Merci d’avoir acheté un produit Omcan. Pour enregistrer votre garantie pour ce produit, complétez les informations ci-dessous, détachez la
carte au niveau de la perforation, puis l’envoyer à l’adresse spécié ci-dessous. Vous pouvez également vous inscrire en ligne en visitant:
Gracias por comprar un producto Omcan usted. Para registrar su garantía para este producto, complete la información a continuación,
cortar la tarjeta en la perforación y luego enviarlo a la dirección indicada a continuación. También puede registrarse en línea en:
www.omcan.com/warrantyregistration.html
For mailing in Canada
Pour postale au Canada
Por correo en Canadá
OMCAN
PRODUCT WARRANTY REGISTRATION
3115 Pepper Mill Court,
Mississauga, Ontario
Canada, L5L 4X5
PRODUCT WARRANTY REGISTRATION
4450 Witmer Industrial Estates, Unit 4,
For mailing in the US
Pour diusion aux États-Unis
Por correo en los EE.UU.
OMCAN
Niagara Falls, New York
USA, 14305
or email to: service@omcan.com
Purchaser’s Information
Name: Company Name:
Address:
Telephone:
City: Province or State: Postal or Zip: Email Address:
Country: Type of Company:
Restaurant Bakery Deli
Dealer from which Purchased: Butcher Supermarket Caterer
Dealer City: Dealer Province or State: Institution (specify):
Invoice: Other (specify):
Model Name: Model Number: Serial Number:
Machine Description:
Date of Purchase (MM/DD/YYYY): Date of Installation (MM/DD/YYYY):
Would you like to extend the warranty? Yes No
Thank you for choosing Omcan | Merci d’avoir choisi Omcan | Gracias por elegir Omcan
19
Since 1951 Omcan has grown to become a leading distributor of equipment and supplies to the North
American food service industry. Our success over these many years can be attributed to our commitment
to strengthen and develop new and existing relationships with our valued customers and manufacturers.
Today with partners in North America, Europe, Asia and South America, we continually work to improve
and grow the company. We strive to offer customers exceptional value through our qualied local sales
and service representatives who provide convenient access to over 5,000 globally sourced products.
Depuis 1951 Omcan a grandi pour devenir un des “leaders” de la distribution des équipements et
matériel pour l’industrie des services alimentaires en Amérique du Nord. Notre succès au cours de ces
nombreuses années peut être attribué à notre engagement à renforcer et à développer de nouvelles
et existantes relations avec nos clients et les fabricants de valeur. Aujourd’hui avec des partenaires en
Amérique du Nord, Europe, Asie et Amérique du Sud, nous travaillons continuellement à améliorer et
développer l’entreprise. Nous nous efforçons d’offrir à nos clients une valeur exceptionnelle grâce à
nos ventes locales qualiées et des représentants de service qui offrent un accès facile à plus de 5000
produits provenant du monde entier.
Desde 1951 Omcan ha crecido hasta convertirse en un líder en la distribución de equipos y suministros
de alimentos en América del Norte industria de servicios. Nuestro éxito en estos años se puede atribuir
a nuestro compromiso de fortalecer y desarrollar nuevas relaciones existentes con nuestros valiosos
clientes y fabricantes. Hoy con socios de América del Norte, Europa, Asia y América del Sur, que trabajan
continuamente para mejorar y crecer la empresa. Nos esforzamos por ofrecer a nuestros clientes valor
excepcional a través de nuestro local de ventas y representantes de los servicios que proporcionan un
fácil acceso a más de 5,000 productos con origen a nivel mundial.
Loading...