Omcan BB-CN-0017-HC User Manual

Reach In Bottle Coolers

Models BB-CN-0005-HC, 0014-HC, 0017-HC, 0026-HC

Items 50038, 50039, 50040, 50041

Instruction Manual

Revised - 08/23/2019

Toll Free: 1-800-465-0234

Fax: [phone]

Email: [e-mail]

www.omcan.com

Table of Contents

Model BB-CN-0005-HC / Model BB-CN-0014-HC
Model BB-CN-0017-HC / Model BB-CN-0026-HC

Section

General Information

Safety and Warranty

Technical Specications

Installation / Operation

Maintenance

Troubleshooting

------------------------------------------------------------------------------------ 8 - 9

--------------------------------------------------------------------------- 3 - 4

--------------------------------------------------------------------------- 4 - 5

------------------------------------------------------------------------------- 9 - 10

Page

-------------------------------------------------------------------------- 6

------------------------------------------------------------------------ 6 - 8

Parts Breakdown

Electrical Schematics

Warranty Registration

---------------------------------------------------------------------------- 11 - 18

---------------------------------------------------------------------- 19 - 22

---------------------------------------------------------------------------- 23

2

General Information

Omcan Manufacturing and Distributing Company Inc., Food Machinery of America, Inc. dba Omcan
and Omcan Inc. are not responsible for any harm or injury caused due to any person’s improper or
negligent use of this equipment. The product shall only be operated by someone over the age of 18, of

sound mind, and not under the inuence of any drugs or alcohol, who has been trained in the correct
operation of this machine, and is wearing authorized, proper safety clothing. Any modication to the
machine voids any warranty, and may cause harm to individuals using the machine or in the vicinity of
the machine while in operation.

CHECK PACKAGE UPON ARRIVAL

Upon receipt of an Omcan shipment please inspect for external damage. If no damage is evident on the
external packaging, open carton to ensure all ordered items are within the box, and there is no concealed
damage to the machine. If the package has suffered rough handling, bumps or damage (visible or concealed),
please note it on the bill of lading before accepting the delivery and contact Omcan within 24 hours, so we may
initiate a claim with the carrier. A detailed report on the extent of the damage caused to the machine must be

lled out within three days, from the delivery date shown in the shipping documents. Omcan has no recourse

for damaged products that were shipped collect or third party.

Before operating any equipment, always read and familiarize yourself with all operation and safety

instructions.

Omcan would like to thank you for purchasing this machine. It’s of the utmost importance to save
these instructions for future reference. Also save the original box and packaging for shipping the

equipment if servicing or returning of the machine is required.

---------------------------------------------------------------------------------------------------------------------------------------------------

Omcan Fabrication et distribution Companie Limité et Food Machinery d’Amerique, dba Omcan et
Omcan Inc. ne sont pas responsables de tout dommage ou blessure causé du fait que toute personne
ait utilisé cet équipement de façon irrégulière. Le produit ne doit être exploité que par quelqu’un de

plus de 18 ans, saine d’esprit, et pas sous l’inuence d’une drogue ou d’acohol, qui a été formé pour
utiliser cette machine correctement, et est vêtu de vêtements de sécurité approprié. Toute modication

de la machine annule toute garantie, et peut causer un préjudice à des personnes utilisant la machine
ou des personnes à proximité de la machine pendant son fonctionnement.

VÉRIFIEZ LE COLIS DÈS RÉCEPTION

Dès réception d’une expédition d’Omcan veuillez inspecter pour dommages externes. Si aucun dommage

n’est visible sur l’emballage externe, ouvrez le carton an de s’assurer que tous les éléments commandés

sont dans la boîte, et il n’y a aucun dommage dissimulé à la machine. Si le colis n’a subi aucune mauvaises
manipulations, de bosses ou de dommages (visible ou cachée), notez-le sur le bond de livraison avant

d’accepter la livraison et contactez Omcan dans les 24 heures qui suivent, pour que nous puissions engager

une réclamation auprès du transporteur. Un rapport détaillé sur l’étendue des dommages causés à la machine

doit être rempli dans un délai de trois jours, à compter de la date de livraison indiquée dans les documents
d’expédition. Omcan n’a aucun droit de recours pour les produits endommagés qui ont été expédiées ou cueilli

par un tiers transporteur.

3

General Information

Avant d’utiliser n’importe quel équipement, toujours lire et vous familiariser avec toutes les opérations
et les consignes de sécurité.

Omcan voudrais vous remercier d’avoir choisi cette machine. Il est primordial de conserver ces

instructions pour une référence ultérieure. Également conservez la boîte originale et l’emballage pour

l’expédition de l’équipement si l’entretien ou le retour de la machine est nécessaire.

---------------------------------------------------------------------------------------------------------------------------------------------------

Omcan Empresa De Fabricacion Y Distribucion Inc. Y Maquinaria De Alimentos De America, Inc. dba
Omcan y Omcan Inc. no son responsables de ningun daño o perjuicío causado por cualquier persona
inadecuada o el uso descuidado de este equipo. El producto solo podra ser operado por una persona

mayor de 18 años, en su sano juicio y no bajo alguna inuencia de droga o alcohol, y que este ha sido
entrenado en el correcto funcionamiento de esta máquina, y ésta usando ropa apropiada y autorizada.
Cualquier modicación a la máquina anúla la garantía y puede causar daños a las personas usando la

máquina mientras esta en el funcionamiento.

REVISE EL PAQUETE A SU LLEGADA

Tras la recepcion de un envio Omcan favor inspeccionar daños externos. Si no hay daños evidentes en el

empaque exterior, Habra el carton para asegurararse que todos los articulos solicitados ésten dentro de la
caja y no encuentre daños ocultos en la máquina. Si el paquete ha sufrido un manejo de poco cuidado, golpes

o daños (visible o oculto) por favor anote en la factura antes de aceptar la entrega y contacte Omcan dentro

de las 24 horas, de modo que podamos iniciar una reclamación con la compañia. Un informe detallado sobre
los daños causados a la máquina debe ser llenado en el plazo de tres días, desde la fecha de entrega que se
muestra en los documentos de envío. Omcan no tiene ningun recurso por productos dañados que se enviaron

a recoger por terceros.

Antes de utilizar cualquier equipo, siempre lea y familiarizarse con todas las instrucciones de

funcionamiento y seguridad.

Omcan le gustaría darle las gracias por la compra de esta máquina. Es de la mayor importancia para
salvar estas instrucciones para futuras consultas. Además, guarda la caja original y el embalaje para el

envío del equipo si servicio técnico o devolución de la máquina que se requiere.

Safety and Warranty

Please pay close attention to the safety notices in this section. Disregarding these notices may lead to
serious injury and/or damage to the unit.

ATTENTION

• To minimize shock and re hazards, be sure not to overload outlet. Please designate one outlet for your

unit.

4

Safety and Warranty

• Do not use extension cords.

• Do not put your hands under the unit when the units is required to be moved.

• When the unit is not in use for a long period of time, please unplug the unit from the outlet.

• After unplugging the unit, wait at least 10 minutes before re-plugging it. Failure to do so could cause

damage to the compressor.

UNPLUG CORD

• To minimize shock and re hazards, please do not plug or unplug the cord with wet hands.

• During maintenance and cleaning, please unplug the unit.

PROPER GROUNDING REQUIRED

• To minimize shock and re hazards, make sure that the unit is properly grounded.

PROHIBITION

• Do not attempt to remove or repair any component unless instructed by factory.

• Make sure that the unit is not resting on or against the electrical cord and plug.

• To minimize personal injury, do not hang on the doors.

• Do not store any ammable and explosive gas or liquids inside the unit.

• Do not attempt to alter or tamper with the electrical cord.

• Do not set the desired temperature out of the recommended temperature range: (Ref: 32°F - 50°F).

2 YEARS PARTS AND LABOUR / 5 YEARS PARTS ONLY ON COMPRESSOR

WARRANTY

Within the warranty period, contact Omcan Inc. at 1-800-465-0234 to schedule an Omcan authorized

service technician to repair the equipment locally.

Unauthorized maintenance will void the warranty. Warranty covers electrical and part failures, not

improper use.

Please see https://omcan.com/disclaimer for complete info.

WARNING:

The packaging components are classied as normal solid urban waste and can therefore be disposed of
without difculty.

In any case, for suitable recycling, we suggest disposing of the products separately (differentiated
waste) according to the current norms.

DO NOT DISCARD ANY PACKAGING MATERIALS IN THE ENVIRONMENT!

5

Technical Specications

Model BB-CN-0005-HC BB-CN-0014-HC BB-CN-0017-HC BB-CN-0026-HC

Product
Capacity

Power 1/6 HP 1/4 HP

Net Volume 141 L / 5 cu.ft. 382 L / 13.5 cu.ft. 488 L / 17.23 cu.ft. 580 L / 20.5 cu.ft.
Temperature

Range
Electrical 115V / 60Hz / 1Ph
Amps 2.04A 2.28A 2.6A 4.2A
Refrigerant R290
Isolation

Material
Cooling

System
Defrosting Automatic

Dimensions

Interior
Dimensions

Weight 154 lbs. / 69.9 kgs. 181 lbs. / 82 kgs. 253 lbs. / 115 kgs. 341.7 lbs. / 155 kgs.
Item Number 50038 50039 50040 50041

12 oz bottles - 4.5

cases

12 oz cans - 6 cases

28.1” x 26.4” x 34.2”
714 x 670 x 869mm

22.3” x 23” x 15.7”

566 x 584 x 399mm

12 oz. bottles - 16.5

cases

12 oz. cans - 24 cases

0.5 - 3.3°C / 33 - 38°F

Cyclopentane

28” x 49.5” x 34.2”

713 x 1257 x 869mm

23” x 45” x 26”

584 x 1143 x 660mm

12 oz. bottles - 22 cases

12 oz. cans - 32 cases

Ventilated

28” x 64.5” x 34.2”

713 x 1638 x 869mm

23” x 60” x 26”

584 x 1524 x 600mm

12 oz. bottles - 37.5 cases

12 oz. cans - 55 cases

28” x 95.2” x 34.2”

713 x 2418 x 869mm

23” x 91” x 26”

583 x 2314 x 662mm

Installation / Operation

IMPORTANT!!!PLEASE READ BEFORE INSTALLATION

• If the unit has recently been transported. Please let unit stand still for a minimum of 24 hours before

plugging it in.

• Make sure that the unit drops down to desired temperature before loading the unit with product.

• Maker sure that there is proper ventilation around the unit in the area where it will operate.

• Make sure all accessories are installed(i.e. shelves, shelf clips, casters) before plugging the unit in.

• Please read through the Operation / Owners Manual in its entirety.

CABINET LOCATION GUIDELINES

• Install the unit on strong and leveled surfaces.

- Unit may make unpleasant noises if surface is uneven.

6

Installation / Operation

- Unit may malfunction if surface is uneven.

• Install the unit in an indoor, well-ventilated area.

- Unit performs more efciently in a well-ventilated area.

- For best performance, please maintain clearance of 6” on the back of the unit.

- Outdoor use may cause decreased efciency and damage to the unit.

• Avoid installation in a high humidity and/or dusty area.

- Humidity could cause unit to rust and decrease efciency of the unit.

- Dust collected on condenser coil will cause unit to malfunction. Clean the condenser at least once a

month with a brush or clean cloth.

• Select a location away from heat and moisture-generating equipment.

- High ambient temperature will cause the compressor to overwork, leading to higher energy bills and

gradual breakdown of the unit.

ELECTRICAL

Please ensure that the required voltage of the compressor is being supplied at all times. Low or high voltage

can detrimentally affect the refrigeration unit. All units should be plugged into a grounded and properly-sized

electrical outlet with appropriate overcurrent protection. Please refer to the electrical requirement on the
nameplate. Please make sure that your unit has its own dedicated outlet. Do not use an extension cord.

TEMPERATURE CONTROLS

The temperature controls are factory-set to maintain an average temperature of 38°F in refrigeration. To

maintain a different temperature, simply adjust the control knob located inside the unit. To decrease the
temperature (colder), turn clockwise. To increase the temperature(warmer), turn counter-clockwise – see
diagram.

LOADING PRODUCT

The bin dividers have been installed at the factory for your convenience. Feel free to reposition the dividers
as you see t. To remove the bin dividers, simply push the divider towards the back wall unit the front of the

divider is removed from the positioning holes. To install, position the divider to the desired holes, making sure
that the pressure spring is installed properly.

PAY CLOSE ATTENTION TO THE LOAD LIMIT STICKERS LOCATED ON THE INTERIOR WALLS TO THE
UNIT. DO NOT LOAD PRODUCT ABOVE THE LOAD LIMIT STICKERS OR ABOVE THE TOP CROSS BAR
OF THE BIN DIVIDERS. LOADING PRODUCT ABOVE THE LOAD LIMIT STICKERS WILL HARM THE
PERFORMANCE OF THE UNIT.

7

Installation / Operation

CAUTION

Setting the temperature control to the coldest

setting may cause the Evaporator coil to freeze

and ice up. This will eventually result in a warmer

Cabinet temperature.

Temperature range from 7 (coldest) to 1

(warmest).

Do not load Product above the top crossbar.

Doing so will harm the Refrigeration.

MECHANICAL CONTROLLER INSTRUCTIONS

OFF: shut the compressor off

Temperature range from 7 (coldest) to 1 (warmest).

CAUTION: Setting the temperature control to the coldest setting may cause the
evaporator coil to freeze and ice up. This will eventually result in a warmer cabinet
temperature.

Maintenance

CLEANING THE CONDENSER COIL

• For efcient operation, it is important that the condenser surface be kept free of dust, dirt, and lint.

• We recommend cleaning the condenser coil and ns at least once per month.

• Clean with a commercial condenser coil cleaner, available from any kitchen equipment retailer. Brush the
condenser ns from top to bottom, not side to side.

• After cleaning, straighten any bent condenser ns with a n comb.

CLEANING THE FAN BLADE AND MOTOR

• If necessary, clean the fan blades and motor with a soft cloth. If it is necessary to wash the fan blades,
cover the fan motor to prevent moisture damage.

CLEANING THE INTERIOR OF UNIT

• When cleaning the cabinet interior, use a solvent of warm water and mild soap.

• Do not use steel wool, caustic soap, abrasive cleaners, or bleach that may damage the stainless steel

8

Maintenance

surface.

• Wash door gaskets on a regular basis, preferably weekly. Simply remove door gasket from the frame of the
door, soak in warm water and soap for thirty (30) minutes, dry with soft cloth, and replace.

• Check door gaskets for proper seal after they are replaced.

• Periodically remove the shelves and pilasters from the unit and clean them with mild soap and warm water.
To remove the pilasters, rst remove the shelves and shelf brackets. Then, simply lift the pilaster up and

out.

WARNING: Disconnect power cord before cleaning any parts of the unit.

Troubleshooting

Before requesting any service on your unit, please check the following points. Please note that this guide serve

only as a reference for solutions to common problems.

PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION

Compressor not running. Fuse blown or circuit breaker

tripped.

Power cord unplugged. Plug in power cord.

Thermostat set too high. Set thermostat to lower

Cabinet in defrost cycle. Wait for defrost cycle to nish.

Condensing unit runs for long

periods of time.

Excessive amount of warm product
Placed in cabinet.

Prolonged door opening or door

ajar.

Door gasket(s) not sealing
properly.

Dirty condenser coil. Clean the condenser coil.
Evaporator coil iced over. Unplug unit and allow coil to

Replace fuse or reset circuit
breaker.

Temperature.

Allow adequate time for Product to

cool down.

Ensure doors are closed when not

in use. Avoid opening doors for
long periods of time.

Ensure gaskets are snapped in
Completely. Remove gasket and
Wash with soap and water. Check

condition of gasket and Replace if
necessary.

defrost. Make sure thermostat is

not set too cold. Ensure that door

gasket(s) are sealing properly.

9

Troubleshooting

Cabinet Temperature Is too warm. Thermostat set too warm. Set thermostat to lower

Temperature.

Blocking air ow. Re-arrange product to allow for

Proper air ow. Make sure there

Is at least four inches of clearance
from evaporator.

Excessive amount of warm product
Placed in cabinet.

Fuse blown or circuit breaker

tripped.
Dirty condenser coil. Clean the condenser coil.

Prolonged door opening or door

ajar.

Evaporator coil iced over. (See above)

Cabinet is noisy. Loose part(s). Locate and tighten loose part(s).

Tubing vibration. Ensure tubing is free from contact

Allow adequate time for product to

cool down.
Replace fuse or reset circuit

breaker.

Ensure doors are closed when not

in use. Avoid opening doors for
long periods of time.

with other tubing or components.

For service call 1-800-465-0234.

REFERENCE

Item Number Model Number Description Manufacturer Model Number

50038 BB-CN-0005-HC

50039 BB-CN-0014-HC

50040 BB-CN-0017-HC

50041 BB-CN-0026-HC

Cooler Back Bar 5 cu ft Reach In

115V/60/1 ETL cETLus INTERTEK

Cooler Back Bar 13.5 cu ft Reach In

115V/60/1 ETL cETLus INTERTEK

Cooler Back Bar 17.2 cu ft Reach In

115V/60/1 ETL cETLus INTERTEK

Cooler Back Bar 25.8 cu ft Reach In

115V/60/1 ETL cETLus INTERTEK

JBC-25-HC

JBC-50-HC

JBC-65-HC

JBC-95-HC

10

Model BB-CN-0005-HC 50038

Parts Breakdown

11

Parts Breakdown

Model BB-CN-0005-HC 50038

Item No. Description Position Item No. Description Position Item No. Description Position

AA183

AA184

AA185 Leveling Feet for JBC-25-HC 3 AA199 Base Board for Lock for JBC-25-HC 17 AA211 Outer Drain Pan for JBC-25-HC 31

AA186 Cabinet Base for JBC-25-HC 4 AA200

AA187 Front Grill for JBC-25-HC 5 AA201

AA188 Back Grill for JBC-25-HC 6 AA202

AA189 Door for JBC-25-HC 7 AA128 Evaporator Fan Motor for JBC-25-HC 21 AA124 Power Switch for JBC-25-HC 35

AA190 Door Gasket for JBC-25-HC 8 AA203 Evaporator for JBC-25-HC 22 AA123 Thermostat for JBC-25-HC 36

AA191 Door Handle for JBC-25-HC 9 AA204 Evaporator Cover for JBC-25-HC 23 AA215

AA192 Back Limit Block for JBC-25-HC 10 AA205 Inner Drain Pipe for JBC-25-HC 24 AA216 Drain Tube for JBC-25-HC 38

AA193 Door Limit Block for JBC-25-HC 11 AA206 Inner Drain Pan for JBC-25-HC 25 AA217

AA194 Panel Under Table for JBC-25-HC 12 64172 Compressor for JBC-25-HC 26 AA135 Power Cord for JBC-25-HC 40

AA195 Under Table Component for JBC-25-HC 13 AA207

AA196 Key for JBC-25-HC 14 AA208 Condenser Fan Blade for JBC-25-HC 28 AA129 Filter Fixer for JBC-25-HC 42

Compressor Unit Installation Board for
JBC-25-HC

Installation Board Limited Block for
JBC-25-HC

1 AA197 Lock for JBC-25-HC 15 AA209 Condenser Fan Motor for JBC-25-HC 29

2 AA198 Top Board for JBC-25-HC 16 AA210 Condenser for JBC-25-HC 30

Evaporator Fan Right and Left Bafe for

JBC-25-HC

Evaporator Fan Motor Cover for JBC­25-HC

Evaporator Fan Bottom Bafe for

JBC-25-HC

Condenser Fan Motor Cover for JBC­25-HC

18 AA212

19 AA213 Fixer for Front Grill for JBC-25-HC 33

20 AA214

27 AA130

Right Rail for Installation Board for
JBC-25-HC

Thermostat Water Proof Cover for
JBC-25-HC

Thermostat Installation Cover for
JBC-25-HC

Left Rail for Installation Board for
JBC-25-HC

Filter for JBC-25-HC 41

32

34

37

39

12

Model BB-CN-0014-HC 50039

Parts Breakdown

13

Parts Breakdown

Model BB-CN-0014-HC 50039

Item No. Description Position Item No. Description Position Item No. Description Position

AA218

AA219 Base Board for JBC-50-HC 2 AA233 Top Board for JBC-50-HC 19 AA245 Bottle Opener Board for JBC-50-HC 36

AA185 Leveling Feet for JBC-50-HC 3 AA234

AA220 Front Grill for JBC-50-HC 4 AA235 Evaporator Cover for JBC-50-HC 21 64172 Compressor for JBC-50-HC 38

AA221 Cabinet Base for JBC-50-HC 5 AA201

AA222 Door for JBC-50-HC 6 AA128 Evaporator Fan Motor for JBC-50-HC 23 AA248 Condenser Fan Blade for JBC-50-HC 40

AA191 Door Handle for JBC-50-HC 7 AA236 Inner Drain Pan for JBC-50-HC 24 AA249

AA223 Door Gasket for JBC-50-HC 8 AA237 Cabinet for JBC-50-HC 25 AA130 Filter for JBC-50-HC 42

AA224 Door Limit Block for JBC-50-HC 9 AA238

AA225 Shelf for JBC-50-HC 10 AA192 Back Limit Block for JBC-50-HC 27 AA216 Drain Tube for JBC-50-HC 44

AA226 Shelf Spring for JBC-50-HC 11 AA239 Back Grill for JBC-50-HC 28 AA250 Condenser for JBC-50-HC 45

AA227 Shelf Cap for JBC-50-HC 12 AA240 Inner Bafe for JBC-50-HC 29 AA251 Outer Drain Pan for JBC-50-HC 46

AA228 Panel Under Table for JBC-50-HC 13 AA241

AA229 Under Table Component for JBC-50-HC

AA197 Lock for JBC-50-HC 15 AA124 Power Switch for JBC-50-HC 32 AA214

AA230 Base Board for Lock for JBC-50-HC 16 AA242 Evaporator for JBC-50-HC 33 AA253 Thermostat Bafe for JBC-50-HC 50

AA231 Decoration Cover for JBC-50-HC 17 AA243

Compressor Unit Installation Board for
JBC-50-HC

1 AA232 Decoration Strip for JBC-50-HC 18 AA244 Bottle Opener for JBC-50-HC 35

Left Support for Evaporator Cover for
JBC-50-HC

Evaporator Fan Motor Cover for JBC­50-HC

Right Support for Evaporator Cover for
JBC-50-HC

Thermostat Installation Cover for
JBC-50-HC

14 AA123 Thermostat for JBC-50-HC 31 AA196 Key for JBC-50-HC 48

Screw for Bottle Opener Component for
JBC-50-HC

20 AA246 Bottle Opener Cover for JBC-50-HC 37

22 AA247 Condenser Fan Motor for JBC-50-HC 39

Condenser Fan Motor Cover for JBC­50-HC

26 AA129 Filter Fixer for JBC-50-HC 43

30 AA252 Power Cord for JBC-50-HC 47

Thermostat Water Proof Cover for
JBC-50-HC

34

41

49

14

Model BB-CN-0017-HC 50040

Parts Breakdown

15

Parts Breakdown

Model BB-CN-0017-HC 50040

Item No. Description Position Item No. Description Position Item No. Description Position

AA254

AA255 Base Board for JBC-65-HC 2 AA265 Top Board for JBC-65-HC 19 AA275 Bottle Opener Board for JBC-65-HC 36

AA185 Leveling Feet for JBC-65-HC 3 AA266

AA256 Front Grill for JBC-65-HC 4 AA267 Evaporator Cover for JBC-65-HC 21 64172 Compressor for JBC-65-HC 38

AA257 Cabinet Base for JBC-65-HC 5 AA201

AA258 Door for JBC-65-HC 6 AA128 Evaporator Fan Motor for JBC-65-HC 23 AA248 Condenser Fan Blade for JBC-65-HC 40

AA191 Door Handle for JBC-65-HC 7 AA268 Inner Drain Pan for JBC-65-HC 24 AA249

AA259 Door Gasket for JBC-65-HC 8 AA269 Cabinet for JBC-65-HC 25 AA130 Filter for JBC-65-HC 42

AA260 Door Limit Block for JBC-65-HC 9 AA270

AA225 Shelf for JBC-65-HC 10 AA192 Back Limit Block for JBC-65-HC 27 AA216 Drain Tube for JBC-65-HC 44

AA226 Shelf Spring for JBC-65-HC 11 AA271 Back Grill for JBC-65-HC 28 AA250 Condenser for JBC-65-HC 45

AA227 Shelf Cap for JBC-65-HC 12 AA272 Inner Bafe for JBC-65-HC 29 AA276 Outer Drain Pan for JBC-65-HC 46

AA261 Panel Under Table for JBC-65-HC 13 AA273

AA262 Under Table Component for JBC-65-HC

AA197 Lock for JBC-65-HC 15 AA124 Power Switch for JBC-65-HC 32 AA214

AA263 Base Board for Lock for JBC-65-HC 16 AA274 Evaporator for JBC-65-HC 33 AA277 Thermostat Bafe for JBC-65-HC 50

AA231 Decoration Cover for JBC-65-HC 17 AA243

Compressor Unit Installation Board for
JBC-65-HC

1 AA264 Decoration Strip for JBC-65-HC 18 AA244 Bottle Opener for JBC-65-HC 35

Left Support for Evaporator Cover for
JBC-65-HC

Evaporator Fan Motor Cover for JBC­65-HC

Right Support for Evaporator Cover for
JBC-65-HC

Thermostat Installation Cover for
JBC-65-HC

14 AA123 Thermostat for JBC-65-HC 31 AA196 Key for JBC-65-HC 48

Screw for Bottle Opener Component for
JBC-65-HC

20 AA246 Bottle Opener Cover for JBC-65-HC 37

22 AA247 Condenser Fan Motor for JBC-65-HC 39

Condenser Fan Motor Cover for JBC­65-HC

26 AA129 Filter Fixer for JBC-65-HC 43

30 AA252 Power Cord for JBC-65-HC 47

Thermostat Water Proof Cover for
JBC-65-HC

34

41

49

16

Model BB-CN-0026-HC 50041

Parts Breakdown

17

Parts Breakdown

Model BB-CN-0026-HC 50041

Item No. Description Position Item No. Description Position Item No. Description Position

AA278

AA279 Base Board for JBC-95-HC 2 AA289 Top Board for JBC-95-HC 19 AA299 Bottle Opener Board for JBC-95-HC 36

AA185 Leveling Feet for JBC-95-HC 3 AA290

AA280 Front Grill for JBC-95-HC 4 AA291 Evaporator Cover for JBC-95-HC 21 64168 Compressor for JBC-95-HC 38

AA281 Cabinet Base for JBC-95-HC 5 AA201

AA282 Door for JBC-95-HC 6 AA128 Evaporator Fan Motor for JBC-95-HC 23 AA248 Condenser Fan Blade for JBC-95-HC 40

AA191 Door Handle for JBC-95-HC 7 AA292 Inner Drain Pan for JBC-95-HC 24 AA249

AA283 Door Gasket for JBC-95-HC 8 AA293 Cabinet for JBC-95-HC 25 AA130 Filter for JBC-95-HC 42

AA284 Door Limit Block for JBC-95-HC 9 AA294

AA225 Shelf for JBC-95-HC 10 AA192 Back Limit Block for JBC-95-HC 27 AA216 Drain Tube for JBC-95-HC 44

AA226 Shelf Spring for JBC-95-HC 11 AA295 Back Grill for JBC-95-HC 28 AA300 Condenser for JBC-95-HC 45

AA227 Shelf Cap for JBC-95-HC 12 AA296 Inner Bafe for JBC-95-HC 29 AA301 Outer Drain Pan for JBC-95-HC 46

AA285 Panel Under Table for JBC-95-HC 13 AA297

AA286 Under Table Component for JBC-95-HC

AA197 Lock for JBC-95-HC 15 AA124 Power Switch for JBC-95-HC 32 AA214

AA287 Base Board for Lock for JBC-95-HC 16 AA298 Evaporator for JBC-95-HC 33 AA302 Thermostat Bafe for JBC-95-HC 50

AA231 Decoration Cover for JBC-95-HC 17 AA243

Compressor Unit Installation Board for
JBC-95-HC

1 AA288 Decoration Strip for JBC-95-HC 18 AA244 Bottle Opener for JBC-95-HC 35

Left Support For Evaporator Cover for
JBC-95-HC

Evaporator Fan Motor Cover for JBC­95-HC

Right Support for Evaporator Cover for
JBC-95-HC

Thermostat Installation Cover for
JBC-95-HC

14 AA123 Thermostat for JBC-95-HC 31 AA196 Key for JBC-95-HC 48

Screw for Bottle Opener Component for
JBC-95-HC

20 AA246 Bottle Opener Cover for JBC-95-HC 37

22 AA247 Condenser Fan Motor for JBC-95-HC 39

Condenser Fan Motor Cover for JBC­95-HC

26 AA129 Filter Fixer for JBC-95-HC 43

30 AA252 Power Cord for JBC-95-HC 47

Thermostat Water Proof Cover for
JBC-95-HC

34

41

49

18

Model BB-CN-0005-HC 50038

Electrical Schematics

19

Electrical Schematics

Model BB-CN-0014-HC 50039

20

Model BB-CN-0017-HC 50040

Electrical Schematics

21

Electrical Schematics

Model BB-CN-0026-HC 50041

22

Warranty Registration

Thank you for purchasing an Omcan product. To register your warranty for this product, complete the information below, tear off the card at

the perforation and then send to the address specied below. You can also register online by visiting:

Merci d’avoir acheté un produit Omcan. Pour enregistrer votre garantie pour ce produit, complétez les informations ci-dessous, détachez la
carte au niveau de la perforation, puis l’envoyer à l’adresse spécié ci-dessous. Vous pouvez également vous inscrire en ligne en visitant:

Gracias por comprar un producto Omcan usted. Para registrar su garantía para este producto, complete la información a continuación,
cortar la tarjeta en la perforación y luego enviarlo a la dirección indicada a continuación. También puede registrarse en línea en:

https://omcan.com/warranty-registration/

For mailing in Canada

Pour postale au Canada

Por correo en Canadá

OMCAN

PRODUCT WARRANTY REGISTRATION

3115 Pepper Mill Court,

Mississauga, Ontario

Canada, L5L 4X5

PRODUCT WARRANTY REGISTRATION

4450 Witmer Industrial Estates, Unit 4,

For mailing in the US

Pour diffusion aux États-Unis

Por correo en los EE.UU.

OMCAN

Niagara Falls, New York

USA, 14305

or email to: [e-mail]



Purchaser’s Information

Name: Company Name:

Address:

Telephone:

City: Province or State: Postal or Zip: Email Address:

Country: Type of Company:

Restaurant Bakery Deli

Dealer from which Purchased: Butcher Supermarket Caterer

Dealer City: Dealer Province or State: Institution (specify):

Invoice: Other (specify):

Model Name: Model Number: Serial Number:

Machine Description:

Date of Purchase (MM/DD/YYYY): Date of Installation (MM/DD/YYYY):

Would you like to extend the warranty? Yes No

Thank you for choosing Omcan | Merci d’avoir choisi Omcan | Gracias por elegir Omcan

23

Since 1951 Omcan has grown to become a leading distributor of equipment and supplies to the North
American food service industry. Our success over these many years can be attributed to our commitment
to strengthen and develop new and existing relationships with our valued customers and manufacturers.
Today with partners in North America, Europe, Asia and South America, we continually work to improve

and grow the company. We strive to offer customers exceptional value through our qualied local sales

and service representatives who provide convenient access to over 5,000 globally sourced products.

Depuis 1951 Omcan a grandi pour devenir un des “leaders” de la distribution des équipements et
matériel pour l’industrie des services alimentaires en Amérique du Nord. Notre succès au cours de ces
nombreuses années peut être attribué à notre engagement à renforcer et à développer de nouvelles
et existantes relations avec nos clients et les fabricants de valeur. Aujourd’hui avec des partenaires en
Amérique du Nord, Europe, Asie et Amérique du Sud, nous travaillons continuellement à améliorer et
développer l’entreprise. Nous nous efforçons d’offrir à nos clients une valeur exceptionnelle grâce à

nos ventes locales qualiées et des représentants de service qui offrent un accès facile à plus de 5000

produits provenant du monde entier.

Desde 1951 Omcan ha crecido hasta convertirse en un líder en la distribución de equipos y suministros
de alimentos en América del Norte industria de servicios. Nuestro éxito en estos años se puede atribuir
a nuestro compromiso de fortalecer y desarrollar nuevas relaciones existentes con nuestros valiosos
clientes y fabricantes. Hoy con socios de América del Norte, Europa, Asia y América del Sur, que trabajan
continuamente para mejorar y crecer la empresa. Nos esforzamos por ofrecer a nuestros clientes valor
excepcional a través de nuestro local de ventas y representantes de los servicios que proporcionan un
fácil acceso a más de 5,000 productos con origen a nivel mundial.