Page 1
http://www.olympus.com/
PT-EP05L/06L Instruction Manual
PT-EP05L/06L
©2011
Printed in China
VR808501
Jp
En
Fr
De
Sp
Cs
Kr
取扱説明書
Instruction Manual
Mode d’emploi
Bedienungsanleitung
Manual de instrucciones
Page 2
Thank you for buying the Underwater Case PT-EP05L/06L (hereinafter Case).
Please read this instruction manual carefully and use the product safely and correctly. Please keep
this instruction manual for reference after reading it.
Wrong usage may cause damage to the camera inside the Case due to water leakage, and repair
may not be possible.
Before use, perform an advance check as described in this manual.
Introduction
z Unauthorized copying of this manual in part or in full, except for private use, is prohibited.
Unauthorized reproduction is strictly prohibited.
z OLYMPUS IMAGING CORP. shall not be responsible in any way for lost profits or any claims by third
parties in case of any damage occurring from improper use of this product.
Please read the following items before use
z This Case is a precision device designed for use at a water depth within 45 m. Please handle it with
sufficient care.
z Please use the Case correctly after sufficient understanding of the contents of this manual in regard
to handling of the Case, checks before use, maintenance, and storage after use.
z OLYMPUS IMAGING CORP. shall not be responsible for accidents involving immersion of a digital
camera in water. In addition, expenses incurred for damage of internal materials or loss of recorded
contents due to water entering the camera will not be compensated.
z OLYMPUS IMAGING CORP. shall not pay any compensation for accidents (injuries or material
damage) at the time of use.
En
For safe use
This instruction manual uses various pictographs for correct use of the product and to prevent danger to
the user and other person, as well as property damage. These pictographs and their meanings are
shown below.
WARNING
CAUTION
EN 1
This shows the content regarding assumption of possibility of human death or
severe injury in case of handling with disregard of this indication.
This shows the contents regarding assumption of possibility of injury or damage
to property in case of handling with disregard of this indication.
Page 3
For customers in Europe
The "CE" mark indicates that this product complies with the European requirements
for safety, health, environment and customer protection. CE-mark products are for
sale in Europe.
This symbol [crossed-out wheeled bin WEEE Annex IV] indicates separate collection
of waste electrical and electronic equipment in the EU countries.
Please do not throw the equipment into the domestic refuse.
Please use the return and collection systems available in your country for the disposal
of this product.
For customers in USA
FCC Notice
This device complies with part 15 of the FCC rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
Any unauthorized changes or modifications to this equipment would void the user's authority to
operate.
For customers in CANADA
This Class B digital apparatus complies with Canadian ICES-003.
WARNING
1 Keep this product out of the reach of babies, infants, and children. There is the possibility of
occurrence of the following types of accidents.
• Injury by dropping onto the body from heights.
• Injury from parts of the body getting caught in parts which open and close.
• Swallowing of small parts, O-ring, silicone grease and silica gel. Please consult a physician
immediately if any parts have been swallowed.
2 Do not store this product with batteries for light or a digital camera still containing batteries loaded in
it.
Storage with batteries inserted may lead to battery leakage and fire hazard.
3 If leakage of water should occur with a camera installed in this product, quickly remove the batteries
from the camera or the Case. There is the possibility of ignition and explosion from generation of
hydrogen gas.
4 This product is made of resin. There is the possibility that injuries may be caused when it becomes
broken due to strong impact with a rock or other hard objects. Please handle it with sufficient care.
5 Do not look directly at the light when it is on.
En
CAUTION
1 Do not disassemble or modify this product. This may cause water leakage or defect. In case of the
loss of image data caused by disassembly, repair or modification etc. by any party other than those
appointed by OLYMPUS IMAGING CORP., we shall bear no responsibility for damage.
2 Use or storage of the product at the following locations may cause defective operation, defects,
damage, fire, internal fogging, or water leakage. This should be avoided.
• Locations reaching high temperatures such as those under direct sunlight, in an automobile, etc.
• Locations close to fire
• A water depth in excess of 45 m
• Locations subject to vibrations
EN 2
Page 4
En
• Locations with high temperature and humidity or with extreme temperature changes
• Locations with volatile substances
3 Opening and closing at locations with much sand, dust, or dirt may impair the waterproof
characteristic and cause water leakage. This should be avoided.
4 This product is not a case to soften impacts to the camera inside the product. When this product with
a digital camera inside is subjected to impacts or heavy objects are placed onto it, the digital camera
may be damaged. Please handle it with sufficient care.
5 Do not use the following chemicals for cleaning, corrosion prevention, prevention of fogging, repair
or other purposes. When these are used for the Case directly or indirectly (with the chemicals in
vaporized state), they may cause cracking under high pressure or other problems.
Chemicals which cannot be
Volatile organic solvents,
chemical detergents
Anticorrosion agent
Commercial defogging
agents
Grease other than specified
silicone grease
Adhesive
6 Jumping into the water with the Case in your hand, throwing the Case from a boat or ship into the
water, and other rough handling may cause water leakage. Please handle with sufficient care, when
handing it over from hand to hand etc.
7 There is the light circuitry inside, so do not let the inside of the Case getting wet.
8 If the Case interior or the camera should become wet because of water leakage, etc., immediately
wipe off all moisture and contact your local service station or dealer.
9 Be careful not to apply excessive force to the zoom dial, accessory mount or tripod seat.
0 Remove the O-ring when traveling by air. Otherwise air pressure may make it impossible to open the
Case.
a For safe use of the digital camera in this product, please read the “Instruction Manual” for the digital
camera carefully.
b When sealing this product, take sufficient care that no foreign matter gets caught at the O-ring and
the contact surface. It is caused for water leakage.
c The lens port cannot be removed.
d Do not use as an underwater torch for diving.
used
Do not clean the Case with alcohol, gasoline, thinner or other volatile
organic solvents or with chemical detergents etc. Pure water or
lukewarm water is sufficient for cleaning.
Do not use anticorrosion agents. Pure water is sufficient when washing
the metal parts as stainless steel and brass are used.
Do not use commercial defogging agents. Always use the specified
desiccant silica gel.
Use only the specified silicone grease for the O-ring, as otherwise the
O-ring surface may deteriorate and water leakage may occur.
Do not use adhesive for repairs or other purposes. When repair is
required, please contact a dealer or a service station of OLYMPUS
IMAGING CORP.
Explanation
EN 3
Page 5
Battery handling precautions
Follow these important guidelines to prevent batteries from leaking, overheating, burning, exploding, or
causing electrical shocks or burns.
DANGER
z Never heat or incinerate batteries.
z Never contact terminals (+) and (–) with metal.
z Do not use solder, transform, modify or dismantle the batteries.
WARNING
z Keep batteries dry at all times.
z Do not touch the batteries with wet hands.
z Use only batteries recommended for use with this product.
z Never mix batteries (old and new batteries, charged and uncharged batteries, batteries of different
manufacture or capacity, etc.).
z If a battery leaks, becomes discolored or deformed, or becomes abnormal in any other way during
operation, stop using it. It may cause a fire or an electrical shock. Please contact your local service
station or dealer.
z Always remove batteries if they are not used for a long period.
EN 4
En
Page 6
Contents
Introduction ............................................................................................................................ 1
Please read the following items before use ........................................................................... 1
For safe use ........................................................................................................................... 1
Battery handling precautions.................................................................................................. 4
1.Preparations .........................................................................................................7
Check the contents of the package........................................................................................ 7
Names of the parts........................................................................................................... 8
Using the accesories.............................................................................................................. 9
Installing and removing of the LCD hood ......................................................................... 9
Mounting and removing the body cap.............................................................................. 9
Installing the diffuser ...................................................................................................... 10
2.Advance check of the Case...........................................................................11
Advance check before use ................................................................................................... 11
3.Loading the digital camera............................................................................12
Check the digital camera...................................................................................................... 12
Open the Case ..................................................................................................................... 13
Attach the flash to the camera and raise the light emitting part ........................................... 13
Insert the batteries for the light............................................................................................. 14
Load the digital camera ........................................................................................................ 15
Make sure the camera is loaded properly ............................................................................ 15
Seal the Case....................................................................................................................... 16
Attach the diffuser ................................................................................................................ 16
Check the operation of the loaded camera .......................................................................... 16
Water leakage test ............................................................................................................... 17
En
4.Connecting the underwater flash ................................................................18
Connecting the underwater optical fiber cable ..................................................................... 18
5.Installing the underweater conversion lens ............................................19
6.Taking pictures under water.........................................................................20
Select the shooting modes ................................................................................................... 20
Underwater shooting modes ................................................................................................ 20
7.Handling after shooting ..................................................................................21
Wipe off any waterdrop ........................................................................................................ 21
Unload the digital camera and batteries............................................................................... 21
Wash the Case with pure water ........................................................................................... 21
Dry the Case ........................................................................................................................ 22
8.Maintaining the waterproof function..........................................................23
Remove the O-ring...............................................................................................................23
Remove any sand, dirt, etc. ................................................................................................. 23
EN 5
Page 7
Install the O-ring................................................................................................................... 23
Applying grease to the O-ring .............................................................................................. 24
Replace consumable products............................................................................................. 24
9.Appendix ..............................................................................................................25
Specifications....................................................................................................................... 25
Supplied accessories for PT-EP05L/06L ....................................................................... 25
Optional accessories...................................................................................................... 25
EN 6
En
Page 8
1. Preparations
•
Check the contents of the package
Check that all accessories are in the box.
Contact your dealer if accessories are missing or damaged.
Case body
(Check that the O-ring is installed.)
• Hand strap
• LCD hood (on the body)
• Body cap
• O-ring remover
• Silica gel (1g)
• Silicone grease
• Diffuser
En
• Optical fiber cable
insertion slot cap (2)
• Flash window cover
• Antireflective ring
• Instruction manual (this manual)
CAUTION:
• After purchase, be sure to do maintenance even in brand-new condition. Neglecting the maintenance may
become the cause of water leakage.
For how to maintenance the case, refer to P.23.
• The zoom gear PPZR-EP02 (sold separately) is required to use the zoom.
For details, refer to P.12.
EN 7
Page 9
Names of the parts
PT-EP05L
PT-EP06L
1 Open/close dial
2 Slide lock
*3 Shutter lever
*4 ON/OFF button
5 Accessory mount
6 Light ON/OFF button
7 Light
8 Optical fiber cable insertion
slots
9 Zoom dial
*0 q (Play) button
*a (Erase) button
*b Mode dial knob
Note:
Case operation parts marked by * corresponds to the operation parts of the digital camera. When the
operation parts of the Case are operated, the corresponding functions of the digital camera will operate. For
details of the functions, refer to the instruction manual for the digital camera.
*c G/Fn button (PT-EP05L)
*d U button (PT-EP05L)
*e ( (REC) button
*f INFO (Info display) button
*g F (Exposure correction)
button/Cross-cursor button
S
*h# button/Cross-cursor
button X (PT-EP05L)
*i OK button
*j jY button/Cross-cursor
button T
*k MENU button
*l P button/Cross-cursor
button W (PT-EP05L)
m LCD monitor window
n LCD hood
o# button/U button/Cross-
cursor button X
(PT-EP06L)
p P button/G button/
Cross-cursor button W
(PT-EP06L)
q O-ring
r LCD inner hood
s Tripod seat
t Battery box
En
EN 8
Page 10
Using the accesories
Installing and removing of the LCD hood
Installation
Fit the LCD hood as shown in the figure into the rails above and below the LCD monitor window one after
the other.
Removal
Remove the LCD hood from the rails above and below the LCD monitor window one after the other by
widening the LCD hood.
Rails
Installation Removal
Mounting and removing the body cap
Install to fit the concave and convex parts of the body cap and lens port. Be sure to remove the body cap
before shooting.
En
EN 9
Page 11
Installing the diffuser
1 Attach the diffuser to the port adapter.
Port adapter
2 Attach the hand strap on the Case body.
3 Install the diffuser on the Case.
Diffuser
EN 10
En
Page 12
2. Advance check of the Case
Advance check before use
This Case has been the subject of thorough quality control for the parts during the manufacturing
process and thorough function inspections during the assembly. In addition, a water pressure test is
performed with a water pressure tester for all products to confirm that the performance conforms to the
specifications.
However, depending on the carrying, storage conditions and the maintenance status, etc., the
waterproof function may be damaged.
Before using, always perform the following advance checks.
Advance check
1 Before loading the digital camera in the Case, immerse the empty Case to confirm that there is no
water leakage. When it is difficult, water leakage can be checked by referring “Water leakage
test” (P. 17).
2 Main causes of water leakage are as follows.
• Forgetting to install the O-ring
• Part of an O-ring or an entire O-ring is outside the specified groove.
• O-ring damage, cracks, deterioration or deformation
• Sand, fibers, hair or other foreign matter sticking to the O-ring, the O-ring groove or the O-ring
contact surface.
• Damage to an O-ring groove or O-ring contact surface.
• Attached strap or silica gel getting caught when closing the Case.
Perform the test after the above causes have been eliminated.
CAUTION:
If the advance test should show water leakage with normal handling, stop using the Case and contact your
dealer or an Olympus service station.
En
EN 11
Page 13
3. Loading the digital camera
Check the digital camera
Check the digital camera before loading it in the Case.
1. Battery confirmation
It is impossible to change the batteries when using the Case. Make sure that you have sufficient
remaining battery capacity before use.
2. Check the remaining number of pictures
Check that the image storage medium has enough room for the number of pictures you want to take.
3. Remove the strap, lens cap and filter from the digital camera.
If the digital camera is loaded without removing the strap, lens cap and the Case cannot be sealed
properly and water leakage may be caused.
4. When using PT-EP05L, insert the back monitor of the camera.
5. Attach the zoom gear (optional) and the antireflective ring.
POSR-EP03 cannot be used.
M.ZUIKO DIGITAL ED 14-42mm II
M.ZUIKO DIGITAL ED 14-42mm II R
Antireflective ring
Zoom gear Antireflective ring
PPZR-EP02 POSR-EP05 (supplied)
En
EN 12
Page 14
Open the Case
1 Slide and hold the slide lock towards the arrow direction (1) and turn the open/close dial clockwise
(2).
2 Open the rear lid of the Case gently.
1
Slide lock
2
CAUTION:
Do not apply too much force while turning the open/close dial. Doing so may damage the dial.
Attach the flash to the camera and raise the light emitting part
Attach the flash supplied with the camera.
Make sure to raise the light emitting part.
En
EN 13
Page 15
Insert the batteries for the light
Open the battery lid.
Insert 2 AAA batteries on the ribbon. Pay attention to the battery direction.
Close the battery lid.
En
EN 14
Page 16
Load the digital camera
1 Confirm that the digital camera is OFF.
2 Gently load the digital camera into the Case.
3 Insert a silica gel bag (1g) between the bottom of the digital camera and the Case.
The silica gel bag provided for prevention of fogging.
2
3
CAUTION:
• If the silica gel bag is caught when the Case is sealed, water leakage will occur.
• Once silica gel has been used, the moisture absorption performance will be impaired. Always replace the
silica gel when the Case is opened and closed.
• Clean the surface of the dials of the Case and the camera.
The dials may slip if there is grease or foreign matter on them.
En
Make sure the camera is loaded properly
Check the following points before sealing the Case.
• Is the digital camera loaded properly?
• Is silica gel inserted all the way at the specified location?
• Is the O-ring attached properly to the opening on the Case?
• Is there any dirt or foreign matter on the O-ring or the O-ring contact surface on the front lid?
• Is the waterproof function maintenance performed? (For details of the maintenance, refer to
“Maintaining the waterproof function” (P. 23) of this manual.)
EN 15
Page 17
Seal the Case
1 Close the Case gently while aligning the mounting projection of the rear lid and groove of the open/close dial.
2 Turn the open/close dial counter clockwise.
• The Case is sealed.
Close
CAUTION:
• If the open/close dial is not fully turned, the Case will not be sealed. This will cause water leakage.
• Close the rear lid of the Case so that the lens cap or LCD hood strap is not caught. If it is caught, water
leakage may be caused.
Attach the diffuser
• Do not cap to optical fiber cable insertion slot.
Check the operation of the loaded camera
After sealing the Case, check that the camera operations normally.
• Push the ON/OFF button on the Case and confirm that the camera turns ON/OFF.
• Turn the mode dial knob on the Case and confirm that the camera mode switches properly.
• Press the shutter lever on the Case and confirm that the camera shutter releases.
• Operate the zoom dial on the Case and confirm that the camera’s lens is controlled.
• Operate other control buttons on the Case and confirm that the camera functions properly as intended.
• Push the ON/OFF button of the light and confirm that the light turns ON/OFF.
En
EN 16
Page 18
Water leakage test
The final test after loading the camera is explained below. Always perform this test. It can be performed
easily in a water tank or a bathtub. The required time is about five minutes. Confirm the operation of the
different buttons.
• At first, immerse the Case for only three seconds and check that no water drop etc. to inside of the
Case.
• Next, immerse the Case for 30 seconds and check that no water drop etc. to inside of the Case.
• Then, immerse the Case for three minutes, operate all buttons and levers, and check the following:
- check that no water has accumulated inside of the Case.
- check that the Case is not fogged.
- check that no water has entered inside of the Case.
• If inside of the Case is fogged or there is a water drop, do the maintenance of the O-ring and perform
the water leakage test again.
En
EN 17
Page 19
4. Connecting the underwater flash
Connecting the underwater optical fiber cable
To connect the UFL-2 underwater flash (optional) to the Case using an underwater optical fiber cable
(optional: PTCB-E02), follow the procedures below.
Connecting the underwater optical fiber
cable
1 Put the underwater optical fiber cable plug into
the optical fiber cable insertion slot.
Insert firmly until it stops next to the flash window
cover.
2 Put the cap to the optical fiber cable insertion slot
when not in use.
Setting of the digital camera
Set the RC mode of the camera to ON so that the camera's built-in flash is activated.
In case of UFL-2, turn the RC mode to ON.
For details, refer to the instruction manual of UFL-2.
In case of UFL-1, plug the optical fiber cable in the same way.
Turn the RC mode of the camera to OFF.
En
EN 18
Page 20
5. Installing the underweater conversion lens
Attaching the conversion lens.
The underwater macro conversion lens PTMC-01 (optional) and underwater wide conversion lens
PTWC-01 (optional) are supported.
En
Vignetting in the four corners may occur when using the underwater wide conversion lens (PTWC-01)
on land.
Also, the camera built-in flash cannot be used with the underwater wide conversion lens.
EN 19
Page 21
6. Taking pictures under water
Select the shooting modes
For E-PL3
Assign the underwater mode to an Fn button to easily switch to that mode.
Select [ / ] in [Button Function] in [ ] of [ ] in [MENU], then press the OK button.
* [ menu display] of [ ] in [MENU] must be set to ON.
In case of E-PM1, assign to the ((REC) button or Cross-cursor button T.
Note:
• Press the Fn button to switch between Underwater Wide-Angle and Underwater Macro modes.
• Turn the mode dial knob or hold down the Fn button to exit the underwater mode. Press the Fn button again
to return to the underwater mode.
• However, in SCN, iAUTO and movie modes, pressing the Fn button will not set the camera in underwater
mode.
For details, refer to the instruction manual of the digital camera.
Underwater shooting modes
Underwater Wide-Angle
Suitable for shooting a scene that extends across a wide range such as a school of fish swimming
through the water. Background blues are vividly reproduced.
Underwater Macro
Suitable for close-up shooting of small fish and other underwater creatures. Natural colors of the
underwater are accurately reproduced.
EN 20
En
Page 22
7. Handling after shooting
Wipe off any waterdrop
After underwater shooting, remove any water drop from the case. Use pressurized air or a soft, lint-free
cloth to carefully wipe away any moisture from the hinge between the front and rear lids, the shutter lever
and the open/close dial.
CAUTION:
Water left between the front and rear lids can get inside the Case once it is opened. Please dry these areas
carefully.
Unload the digital camera and batteries
Open the Case carefully and remove the digital camera and light batteries.
CAUTION:
• When opening the Case, make sure no water from outside (e.g. drops from your hair or the diving suit) gets
inside the Case and/or on the camera.
• Before opening the case, ensure that your hands or gloves are completely clean (free of sand, loose fibers,
etc.).
• Never open the Case in areas where water could splash or spray or where sand or dust could be blown in
the air. When this cannot be avoided, for example if the battery or memory card needs to be changed, the
Case and camera should be protected from the wind or spray with a plastic sheet or similar object.
• Never touch the digital camera and/or battery when your hands are wet with sea water.
En
Wash the Case with pure water
After use, seal the Case again after taking out the camera and wash it sufficiently in pure water as soon
as possible.
After use in sea water, it is effective to immerse it for a fixed time (30 minutes to 1 hour) in pure water to
remove any salt.
CAUTION:
• Water leakage may occur when a high water pressure is applied partially. Before washing the Case with
water, remove the digital camera from it.
• Operate the shutter lever and each buttons of this produ ct in pure water to remove salt adhering to the shaft.
Do not disassemble for cleaning.
• Letting salt dry on the Case may impair the function. Always wash off any salt after use.
EN 21
Page 23
Dry the Case
After washing with pure water, use a lint-free soft cloth without any salt on it to wipe off any water drop
and dry the Case completely at a well ventilated location in the shade.
CAUTION:
Do not use hot air from a hair drier or the like for drying and do not expose the Case to direct sunlight, as this
may accelerate deterioration and deformation of the Case and deterioration of the O-ring, leading to leakage
of water.
When wiping the Case, take care not to cause scratches.
EN 22
En
Page 24
En
8. Maintaining the waterproof function
The O-ring is a consumable product. Before each use, perform proper maintenance. Always be sure to
perform the O-ring maintenance operation as described below. Neglecting this maintenance may
become the cause of water leakage.
Perform at the location without sand or dust, after washing and drying your hands.
Remove the O-ring
Open the Case and remove the O-ring.
Procedure
1 Insert the O-ring remover into the gap between the O-ring and O-ring groove wall.
2 Bring the tip of the inserted O-ring remover below the O-ring. (Be careful not to damage the groove
with the tip of the O-ring remover.)
3 Lift the O-ring, pinch it with your fingertips and pull it out of the Case.
Remove any sand, dirt, etc.
After visually checking that dirt has been removed from the O-ring, check for attached sand and other
foreign matter, as well as for damage and cracks by squeezing the entire circumference of the O-ring
lightly with your fingertips.
Remove attached foreign matter from the O-ring groove with a clean cloth or a cotton swab. Also remove
any sand or dirt attached to any part of the Case that comes into contact with the O-ring.
CAUTION:
• When a sharp object is used to remove the O-ring or to clean the inside of the O-ring groove, the Case and
the O-ring may be damaged and water leakage may be caused.
• When the O-ring is checked with the fingertips, take care not to stretch the O-ring.
• Never use alcohol, thinner, benzene or similar solvents or chemicals detergents to clean the O-ring. When
such chemicals are used, it is likely that the O-ring will be damaged or that its deterioration will be
accelerated.
Install the O-ring
Confirm that no foreign matter is attached, apply a thin coat of the accessory grease to the O-ring, and
fit the O-ring into the groove. At this time, confirm that the O-ring does not stick out from the groove.
When sealing this product, make sure that no hairs, fibers, sand particles or other foreign matter stick
not only to the O-ring, but also to the contact surface (front cover). Even a single hair or a single grain of
sand may cause water leakage. Please check with special care.
EN 23
Page 25
Applying grease to the O-ring
1 Apply only Olympus
exclusive grease to O-ring.
2 Spread the grease onto the
entire circumference of the
O-ring.
3 Check that the O-ring is free
of scratches or unevenness.
CAUTION:
• Always perform maintenance of the waterproof function even when the Case has been opened every
shooting. Neglecting this maintenance may become the cause of water leakage.
• When the Case is not to be used for a long time, remove the O-ring from the groove to prevent deformation
of the O-ring, apply a thin coat of silicone grease, and store it in a clean plastic bag or the like.
Examples of foreign matter sticking to the O-ring
Make sure that your fingers and the O-ring are
free of dirt, and squeeze about 5 mm of grease
onto a finger. (5 mm is the most appropriate
amount.)
Spread the grease onto the entire
circumference of the O-ring using 3 fingers.
Be careful not to use excessive force as this
may stretch the O-ring.
After spreading the grease, check visually and
by touch that the O-ring is not scratched and
that its surface is flat. If it is damaged in any
way, replace it with a brand-new O-ring.
Hair Fibers Grains of sand
Replace consumable products
• The O-ring is a consumable product. Independent of the number of times the Case is used, it is
recommended that the O-ring should be replaced by a new piece at least once a year.
• Deterioration of the O-ring is accelerated by the usage conditions and the storage conditions. Replace
the O-ring even before a year has passed if it shows signs of damage, cracking or loss of elasticity.
CAUTION:
• Use genuine Olympus silicone grease, silica gel and O-ring.
• Do not try to replace the O-ring by yourself.
• We recommend to perform the check periodically.
En
EN 24
Page 26
9. Appendix
Specifications
Underwater case PT-EP05L PT-EP06L
Supported camera E-PL3 E-PM1
Pressure resistance Depth of down to 45 m (147 feet)
Main materials Main body: Polycarbonate
Light batteries 2 AAA batteries (Alkaline / NiMH)
Lighting time Approx. 4 hours in continuous use (when using alkaline batteries)
Dimensions Width 175 mm × height 149 mm ×
depth 156 mm
Weight Approx. 1,110 g (camera and accessories not included)
Weight under water Approx. –30 g (in the freshwater)
(including camera, lens, zoom gear, antirefletive ring, batteries and media
* We reserve the right to change the external appearance and the specifications without notice.
Supplied accessories for PT-EP05L/06L
O-ring: PO L-EP03
Silicone grease: PSOLG-2
Silica gel: SILCA-5S
LCD hood: PFUD-EP05
Body cap: PBC-EP01
Diffuser: PTDP-EP05
Antireflective ring: POSR-EP05
Flash window cover: PFC-EP05
O-ring remover: PTAC-05
O-ring: Silicone rubber
Width 175 mm × height 149 mm ×
depth 152 mm
card)
En
Optional accessories
Silicone grease: PSOLG-3
Underwater optical fiber cable: PTCB-E02
Bracket: PTBK-E01, PTBK-E02
Short arm: PTSA-02/PTSA-03
Underwater flash: UFL-2, UFL-1
Underwater macro conversion lens: PTMC-01
Underwater wide conversion lens: PTWC-01
Zoom gear: PPZR-EP02
* When use combining PTBK-E01 and the Case, the dedicated washers are necessary in the screw part.
If you have PTBK-E01 to which dedicated washers are not bundled, please contact to customer support
center.
Supplied accessories can be purchased. Products of other model types than those describing above cannot be
used.
EN 25
Page 27
Loading...