Olympia L-6160, L-6170, L-6161, L-6180, L-6171 Installation Manual

Tools:

OLYMPIA FAUCETS, INC.

Interchange City Distribution Center #20
1277 Heil Quaker Boulevard
La Vergne, TN 37086
[phone]
www.olympiafaucets.com

Adjustable Wrench Plumbers Putty Sealant Tape Rags

Model Number: L-6160,L-6170,L-6180,L-6161
L-6171,L-6181,L-6162,L-6172,L-6182

Warnings and Notes:

Check with local plumbing code requirements before installation.
This product should be installed by a local listed plumber.

Do not use plumbers putty on threads.

Installation Steps:

Single Handle Lavatory Faucet

Pop-up Drain Installation:

INSTALLATION

(1) Shut off water supplies. Remove old faucet.
Clean mounting surface in preparation for new
faucet.

(2) Place the faucet in position on the sink.
Apply plumbers putty under the base gasket.
Place washer and tighten with locknut.

(3a) When using ball-nose exible supplies

to connect faucet to water supply lines,

slip coupling nut onto exible supply. Ball-

nose coupling will go partially into shank.
Tighten coupling nut (DO NOT OVER
TIGHTEN). Install opposite end according to
manufacturer’s instruction for both tubes.

(3b) When using stainless steel braided
faucet supply hose, this faucet requires one
end of the supply hose to have a 1/2” female
IPS connection. The other end of this supply
hose must match the thread on the water
supply valve under your sink. Once you’ve

identied the required size, carefully follow

the manufacturer’s installation instructions for
each hose.

(1) Remove pop-up ange from body

(2) Place a ring of putty on the bottom of

ange.

(3) Insert pop-up ange through drain hole
and attach ange to body. Ensure the pop-up

outlet faces towards the back of the sink.
Tighten the locknut securely with a wrench.
Do not overtighten.

(4) Remove the excess putty. Connect the

trap (check manufacturer’s instructions for
installation).

(4) Important: After installation is complete,
remove aerator. Turn water supply on and
allow both hot and cold water to run at least
one minute each. While water is running,
check for leaks. Turn off water and replace
aerator.

(5) Remove pivot rod nut from pop-up body,
ensure the washers is in place, insert pivot
rod, tighten pivot rod nut back to pop-up body.

(6) Push pivot rod down, insert drain plug
carefully. Test to ensure drain plug works
properly.

Exploded Drawing:

(7) Connect lift rod strap to pivot rod by using
clip. Tighten the thumbscrew to connect lift rod
strap to pop-up lift rod.

* Note: Please specify nish/color when ordering.

ITEM # DESCRIPTION

A1 OP-190001* Metal Lever Handle

A2 OP-190002* Metal Loop Handle

A3 OP-190008 Acrylic Ball Handle

A4 OP-490023 Acrylic Handle Adapter

B OP-490003* Cap & Adjusting Ring

C OP-490004 Cam & Washer

D OP-390001 Stainless Steel Ball

E OP-490041 Springs & Seats

F OP-490035* 1.5 GPM Aerator

G OP-530001 Mounting Kit

H OP-590001 Supply Nut

I OP-630004*

OP-630002*

50/50 Pop-Up Drain Assembly
Brass Pop-Up Drain Assembly

1 OP-490002 Hot & Cold Indicator

2 OP-490043 Allen Screw

3 OP-490021 Acrylic Ball Handle Button

4 OP-490022 Acrylic Ball Handle Screw

For more care information or trouble shooting

inquiries about your Olympia product, Please call:

OLYMPIA FAUCETS, INC. [phone]

8AM - 8PM EST (5AM to 5PM PST)

www.olympiafaucets.com