Olivetti 3501MF, 4501, 4501MF, 3501 User Manual

Operation Manual

d-Copia 3501 / 3501MF

d-Copia 4501 / 4501MF

Be sure to become thoroughly familiar with this manual to gain the maximum benefit from the product. Before

installing this product, be sure to read the installation requirements and cautions sections.

Be sure to keep all operation manuals handy for reference including this manual, the "Operation manual (for general information and copier operation)" and operation manuals for any optional equipment which has been installed.

PUBLICATION ISSUED BY:

Olivetti S.p.A. Gruppo Telecom Italia

Via Jervis, 77 - 10015 Ivrea (ITALY) www.olivetti.com

The manufacturer reserves the right to carry out modifications to the product described in this manual at any time and without any notice.

The ENERGY STAR program is an energy reduction plan introduced by the

United States Environmental Protection Agency in response to environmental issues and for the purpose of advancing the development and utilization of more energy efficient office equipment.

ENERGY STAR is a U.S. registered mark.

The mark affixed to the product certifies that the product satisfies the basic quality requirements.

Your attention is drawn to the following actions which could compromise the conformity attested to above, as well

as the characteristics of the product:

• incorrect electrical power supply;

• incorrect installation, incorrect or improper use or use not in compliance with the warnings provided in the

User’s Manual supplied with the product;

• replacement of original components or accessories with others of a type not approved by the manufacturer, or

performed by unauthorised personnel.

orm or by any means, electronic or mechanical, including photocopying, recording or

y any information storage and retrieval system, without permission in writing from

the Pub

lisher.

Warranty

While every effort has been made to make this document as accurate and helpful as possible, Olivetti S.p.A. makes no warranty of any kind with regard to its content. All information included herein is subject to change without notice. Olivetti is not responsible for any loss or damages, direct or indirect, arising from or related to the use of this operation manual. © Copyright Olivetti S.p.A. 2006. All rights reserved. Reproduction, adaptation or translation without prior written permission is prohibited, except as allowed under copyright laws.

Warning:

This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.

In some areas, the "POWER" switch positions are marked "I" and " " on the copier instead of "ON" and "OFF". The symbol " " denotes the copier is not completely de-energized but in a stand-by condition at this "POWER" switch position. If your copier is so marked, please read "I" for "ON" and " " for "OFF".

Caution! For a complete electrical disconnection, pull out the main plug. The socket-outlet shall be installed near the equipment and shall be easily accessible.

Required in IEC-950 (EN 60 950) - Europe

• The equipment should be installed near an accessible socket outlet for easy disconnection.

Required in Appendix ZB of BS 7002 (En 60 950) — United Kingdom

MAINS PLUG WIRING INSTRUCTIONS

The mains lead of this equipment is already fitted with a mains plug which is either a non-rewireable (moulded) or a rewireable type. Should the fuse need to be replaced, a BSI or ASTA approved fuse to BS1362 marked or and of the same rating as the one removed from the plug must be used. Always refit the fuse cover after replacing the fuse on the moulded plug. Never use the plug without the fuse cover fitted. In the unlikely event of the socket outlet in your home not being compatible with the plug supplied either cut-off the moulded plug (if this type is fitted) or remove by undoing the screws if a rewireable plug is fitted and fit an appropriate type observing the wiring code below.

DANGER: The fuse should be removed from the cut-off plug and the plug destroyed immediately and disposed of in a safe manner. Under no circumstances should the cut-off plug be inserted elsewhere into a 13A socket outlet as a serious electric shock may occur.

To fit an appropriate plug to the mains lead, follow the instructions below:

IMPORTANT: The wires in this mains lead are coloured in accordance with the following code:

GREEN-AND-YELLOW: Earth BLUE: Neutral BROWN: Live

As the colours of the wires in this mains lead may not correspond with coloured markings identifying the terminals in your plug, proceed as follows: The wire which is coloured GREEN-AND YELLOW must be connected to the terminal in the plug which is marked with the letter E, or by the safety earth symbol Å@, or coloured green or greenand-yellow. The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured black. The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured red.

If you have any doubt, consult a qualified electrician. WARNING: THIS APPARATUS MUST BE EARTHED.

➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢

➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢

➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣

➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢

DIRECTIVE 2002/96/CE ON THE TREA TMENT, COLLECTION, RECYCLING AND DISPOSAL OF ELECTRIC AND ELECTRONIC DEVICES AND THEIR COMPONENTS

INFORMATION

1. FOR COUNTRIES IN THE EUROPEAN UNION (EU)

The disposal of electric and electronic devices as solid urban waste is strictly prohibited: it must be collected separately. The dumping of these devices at unequipped and unauthorized places may have hazardous effects on health and the

environment. Offenders will be subjected to the penalties and measures laid down by the law.

DISPOSE OF OUR DEVICES CORRECTLY

a) Contact the Local Authorities, who will give you the practical information you need and the instructions for handling the

waste correctly, for example: location and times of the waste collection centres, etc.

b) When you purchase a new device of ours, give a used device similar to the one purchased to our dealer for disposal.

The crossed dustbin symbol on the device means that:

- when it to be disposed of, the device is to be taken to the equipped waste collection centres and is to be handled separately from urban waste;

- The producer guarantees the activation of the treatment, collection, recycling and disposal procedures in accordance with Directive 2002/96/CE (and subsequent amendments).

2. FOR OTHER COUNTRIES (NOT IN THE EU)

The treatment, collection, recycling and disposal of electric and electronic devices will be carried out in accordance with the laws in force in the country in question.

Part 1: General Information

0-1

PRODUCT CONFIGURATIONS

The table below shows the product models covered by this manual.

(As of March 2006)

OPERATION MANUALS

The following operation manuals are provided for the machine. Please read the appropriate manuals as needed for the features you wish to learn about.

● Operation manual (for general information and copier oper ation) (this manual): The first half of this manual pr ovides general inf ormation about the machine, includ ing safety inf ormation, loading paper, removing misfeeds, an d regular maintenance. The second half of the manual explains how to use the copy and document filing functions.

● Key operator's guide: This primarily explains key operator programs for machine management and copier related functions. Key operator programs for the fax, printer and network scanner functions are explained in the manuals for those functions. Key operator programs are used by key operators to configure function settings to meet the needs of the customer.

● Operation manual (for facsimile) This manual explains the proced ures for using the machine as a facsimile. To use the fax function, the facsimile expansion kit must be installed.

● Software setup guide (for printer) This explains how to co nnect the mach ine to y our computer, install the printer driver for Windows , and configur e the printer driver settings.

● Operation manual (for printer)* This manual explains the procedures for using the machine as a printer.

● Operation manual (for network scanner)* This manual explains the procedur es for using the machine as a netwo rk scanner when connected to a computer . To use the network scanner function, the NS3 network scanner expansion kit must be installed. *The operation manual (f or printer) an d the operation manual (f or net work scanner) are pro vided as PDF files in

the CD-ROM. This manual is not provided as printed man ual.

NOTES

● Considerable care has been taken in preparing this manual. If you have any comments or concerns about the manual, please contact your nearest Olivetti Service Department.

● This product has undergone strict quality control and inspection procedures. In the unlikely event that a defect or other problem is discovered, please contact your dealer or nearest Olivetti Service Department.

● Aside from instances provided for by law, Olivetti is not responsible for failures occurring during use of the product or its options, or failures due to incorrect operation of the product and its options, or other f ailures , or f or any damage that occurs due to use of the product.

The display screens , messages, and ke y names show n in the manual ma y diff er fr om those on the actual m achine due to product improvements and modifications.

Model Product configuration

Laser printer

Olivetti d-Copia 4501/d-Copia 4501MF Laser printer

Olivetti d-Copia 3501/d-Copia 3501MF

0-2

Improper installation may damage this product. Please note the following during initial installation and whenever the machine is moved.

1.The machine should be installed near an accessible power outlet for easy connection.

2.Be sure to connect the power cord only to a power outlet that meets the specified voltage and current requirements. Also make certain the outlet is properly grounded. For the power supply requirements, see the

name plate on the back of the main unit.

3.Do not install your machine in areas that are:

damp, humid, or very dusty exposed to direct sunlight poorly ventilated subject to extreme temperature or humidity

changes, e.g., near an air conditioner or heater.

4.Be sure to allow the required space around the machine for servicing and proper ventilation.

A small amount of ozone is produced within the machine during operation. The emission level is insufficient to cause any health hazard.

NOTE:

The present recommended long term exposure limit for ozone is 0.1 ppm (0.2 mg/m

) calculated as an 8 hr. timeweighted average concentration. However, since the small amount that is emitted may have an objectionable odor, it is advisable to place the copier in a ventilated area.

60cm

(23-5/8")

80cm

(31-1/2")

30cm (11-13/16")

60cm (23-5/8")

INSTALLATION REQUIREMENTS

0-3

CAUTIONS

1.Do not touch the photoconductive drum. Scratches or smudges on the drum will cause dirty prints.

2.The fusing unit is extremely hot. Exercise care in this area.

3.Do not look directly at the light source. Doing so may damage your eyes.

4.Five adjusters are provided on all optional stand/paper drawer units. These adjusters should be lowered until they contact the floor. When moving the machine with the optional stand/paper drawer, be sure to raise the adjusters. Also, unlock the two casters at the front of the optional stand/paper drawer. After moving the machine, lower the four adjusters until they reach the floor and lock the two casters.

5.Do not make any modifications to this machine. Doing so may result in personal injury or damage to the machine.

6.Since this machine is heavy, it is recommended that it be moved by more than one person to prevent injury.

7.When connecting this machine to a computer, be sure to first turn both the computer and the machine off.

8.Do not make copies of anything which is prohibited from copying by law. The following items are normally prohibited from printing by national law. Other items may be prohibited by local law.

●

Money

●

tamps

●

Bonds

●

Sto

cks

●

Bank drafts

●

hecks

●

assports

●

river's licences

The part indicated in the illustration is only to be handled by a service technician. Absolutely do not touch this part.

Some models include the document filling function, which stores document image on the machine's hard disk. Stored documents can be called up and printed or transmitted as needed. If a hard disk failure occurs, it will no longer be possible to call up the stored document data. To prevent the loss of important documents in the unlikely event of a hard disk failure, keep the originals of important documents or store the original data elsewhere. With the exception of instances provided for by law, Olivetti S.p.A.: bears no responsibility for any damages or loss due to the loss of stored document data.

"BATTERY DISPOSAL"

THIS PRODUCT CONTAINS A LITHIUM PRIMARY MEMORY BACK-UP BATTERY THAT MUST BE DISPOSED OF PROPERLY. PLEASE CONTACT YOUR LOCAL OLIVETTI DEALER OR AUTHORISED SERVICE REPRESENTATIVE FOR ASSISTANCE IN DISPOSING OF THIS BATTERY.

This product utilizes tin-lead solder, and a fluorescent lamp containing a small amount of mercury. Disposal of these materials may be regulated due to environmental considerations. For disposal or recycling information, please contac t your local author it ies or th e Electr onics Ind ustr ies Allian ce: www.eia.org

Fusing unit

Adjuster

Lock

Release

CAUTIONS

0-4

Laser Information

Wave length

785 nm

+10 nm

-15 nm

Pulse times North America: 35 cpm model: (4.1 µs ± 4.1 ns)/7 mm

45 cpm model: (5.7 µs ± 5.7 ns)/7 mm

Europe: 35 cpm model: (3.8 µs ± 3.8 ns)/7 mm

45 cpm model: (4.4 µs ± 4.4 ns)/7 mm

Output power 0.2 mW - 0.4 mW

At the production line, the output power of the scanner unit is adjusted to 0.4 MILLIWATT PLUS 8 % and is maintained constant by the operation of the Automatic Power Control (APC).

Caution

Use of controls or adjustments or performance of procedures other than those spe cified herein may result in hazardous radiation exposure.

For North America:

SAFETY PRECAUTIONS

This Digital Equipment is rated Class 1 and complies with 21 CFR 1040.10 and 1040.11 of the CDRH standards. This means that the equipment does not produce hazardous laser radiation. For your safety, observe the precautions below.

 Do not remove the cabinet, operation panel or any other covers.  The equipment's exterior covers contain several safety interlock switches. Do not bypass any safety interlock by

inserting wedges or other items into switch slots.

For Europe:

CLASS 1 LASER PRODUCT

LASER KLASSE 1

LUOKAN 1 LASERLAITE

KLASS 1 LASERAPPARAT

CAUTION

INVISIBLE LASER RADIATION WHEN OPEN INTERLOCKS DEFEATED. AVOID EXPOSURE TO BEAM.

VORSICHT

UNSICHTBARE LASERSTRAHLUNG WENN ABDECKUNG GEÖFFNET UND SICHERHEITSVERRIEGELUNG ÜBERBRÜCKT. NICHT DEM STRAHL AUSSETZEN.

ADVARSEL

USYNLIG LASERSTRÅLNING VED ÅBNING, NÅR SIKKERHEDSBRYDERE ER UDE AF FUNKTION. UNDGÅ UDSAETTELSE FOR STRÅLNING.

VAROITUS!

LAITTEEN KÄYTTÄMINEN MUULLA KUIN TÄSSÄ KÄYTTÖOHJEESSA MAINITULLA T A VALLA SAATTAA ALTISTAA KÄYTTÄJÄN TURVALLISUUSLUOKAN 1 YLITTÄVÄLLE NÄKYMÄTTÖMÄLLE LASERSÄTEILYLLE.

VARNING

OM APPARATEN ANVÄNDS PÅ ANNAT SÄTT ÄN I DENNA BRUKSANVISNING SPECIFICERATS, KAN ANVÄNDAREN UTSÄTTAS FÖR OSYNLIG LASERSTRÅLNING, SOM ÖVERSKRIDER GRÄNSEN FÖR LASERKLASS 1.

CLASS 1

LASER PRODUCT

LASER KLASSE 1

CAUTION VORSICHT ADVARSEL ADVERSEL VARNING VARO!

INVISIBLE LASER RADIATION WHEN OPEN AND INTERLOCKS DEFEATED. AVOID EXPOSURE TO BEAM.

Laserstrahl

UNSICHTBARE LASERSTRAHLUNG WENN ABDECKUNG GEÖFFNET UND SICHERHEITSVERRIEGELUNG ÜBERERÜCKT. NICHT DEM STRAHL AUSSETZEN.

USYNLIG LASERSTRÅLING VED ÅBNING, NÅR SIKKERHEDSAFBRYDERE ER UDE AF FUNKTION. UNDGÅ UDSAETTELSE FOR STRÅLNING.

USYNLIG LASERSTRÅLING NÅR DEKSEL ÅPNES OG SIKKERHEDSLÅS BRYTES. UNNGÅ EKSPONERING FOR STRÅLEN.

OSYNLIG LASERSTRÅLNING NÄR DENNA DEL ÄR ÖPPNAD OCH SPÄRRAR ÄR URKOPPLADE. STRÅLEN ÄR FARLIG. BETRAKTA EJ STRÅLEN.

AVATTAESSA JA SUOJALUKITUS OHITETTAESSA OLET ALTTIINA NÄKYMÄTÖNTÄ LASERSÄTEILYLLE. ÄLÄ KATSO SÄTEESEEN.

0-5

CONTENTS

Page

PRODUCT CONFIGURATIONS..................................0-1

OPERATION MANUALS..............................................0-1

INSTALLATION REQUIREMENTS..............................0-2

CAUTIONS...................................................................0-3

 Laser Information .................................................0-4

CONTENTS .................................................................0-5

CHAPTER 1 BEFORE USING THE PRODUCT

INTRODUCTION..........................................................1-2

MAIN FEATURES........................................................1-3

PART NAMES AND FUNCTIONS ...............................1-9

 Exterior.................................................................1-9

 Interior.................................................................. 1-10

 Part names and functions of peripheral devices..1-11

 Operation panel....................................................1-13

 Touch panel .........................................................1-14

TURNING THE POWER ON AND OFF.......................1-17

AUDITING MODE.................................. ......................1-18

 Using the machine when the auditing mode is

enabled ................................................................1-18

CHAPTER 2 MANAGING THE MA CHINE

LOADING PAPER........................................................2-2

 Loading paper in paper tray 1 ..............................2-2

 Changing the paper size in paper tray 1..............2-2

 Specifications of paper trays................................2-3

 Setting the paper type and paper size .................2-5

 Setting the paper size when a special size is

loaded ..................................................................2-6

 Programming and editing paper types .................2-7

 Loading paper in the multi purpose drawer..........2-8

 Specifications (multi purpose drawer) ..................2-10

 Loading paper in the stand/3 x 500 sheet paper

drawer ..................................................................2-10

 Specifications (stand/3 x 500 sheet paper

drawer).................................................................2-10

 Loading paper in the stand/MPD & 2000 sheet

paper drawer........................................................2-11

 Specifications (stand/MPD & 2000 sheet paper

drawer).................................................................2-11

CUSTOM SETTINGS...................................................2-13

 General procedure for custom settings................2-13

 About the settings ................................................2-15

REPLACING THE TONER CARTRIDGE ....................2-16

STORAGE OF SUPPLIES...........................................2-17

MISFEED REMOVAL........................................... .. ......2-18

 Misfeed removal guidance ...................................2-18

 Misfeed in the transport area, fusing area, and

exit area ...............................................................2-19

 Misfeed in the duplex module ..............................2-20

 Misfeed in the paper feed area ............................2-21

REMOVING AN ORIGINAL MISFEED ........................2-23

 Removing a misfed original from the automatic

document feeder..................................................2-23

TROUBLESHOOTING.................................................2-24

CHAPTER 3 PERIPHERAL DEVICES

DUPLEX MODULE.......................................................3-2

 Part names ........................................................ ...3-2

 Specifications .......................................................3-2

 Loading paper in the bypass tray .........................3-3



Troubleshooting (concerning the duplex module)

..3-4

MAIL-BIN STACKER....................................................3-5

 Part names ........................................................ ...3-5

 Specifications .......................................................3-5

 Misfeed in the mail-bin stacker.............................3-6

FINISHER.....................................................................3-7

 Part names ........................................................ ...3-7

 Specifications .......................................................3-7

 Finisher functions .................................................3-8

 Using the finisher functions ..................................3-9

 Staple cartridge replacement................................3-10

 Misfeed in the finisher...........................................3-12

 Troubleshooting finisher problems .......................3-13

SADDLE STITCH FINISHER .......................................3-14

 Part names ........................................................ ...3-14

 Specifications .......................................................3-14

 Saddle stitch finisher functions.............................3-15

 Using the saddle stitch finisher.............................3-18

 Staple cartridge replacement and staple jam

removal.................................................................3-19

 Misfeed in the saddle stitch finisher......................3-22

 Troubleshooting (concerning the saddle stitch

finisher).................................................................3-24

CHAPTER 4 MAKING COPIES

AUTOMATIC DOCUMENT FEEDER...........................4-2

 Acceptable originals .................................... .........4-2

PLACING ORIGINALS.................................................4-3

CHECKING THE SIZE OF A PLACED ORIGINAL ......4-5

 Manually setting the scannin g size.......................4-5

STORING, DELETING, AND USING ORIGINAL

SIZES...........................................................................4-6

 Storing or deleting an original size .......................4-6

NORMAL COPYING.....................................................4-7

 Making copies with the automatic document

feeder ...................................................................4-7

 Automatic two-sided copying using the automatic

document feeder................................................ ...4-10

 Copying from the document glass........................4-11

 Automatic two-sided copying from the document

glass.....................................................................4-13

ADJUSTING THE EXPOSURE....................................4-14

REDUCTION/ENLARGEMENT/ZOOM........................4-15

 Automatic selection (auto image) .........................4-15

 Manual selection (preset copy ratios/zoom).........4-16

 XY ZOOM.............................................................4-18

SPECIAL PAPERS.......................................................4-20

CONTENTS

0-6

CHAPTER 5 CONVENIENT COPY FUNCTIONS

SPECIAL MODES........................................................5-2

 General procedure for using special functions.....5-2

 Margin shift...........................................................5-3

 Erase ....................................................................5-4

 Dual page copy.....................................................5-5

 Pamphlet copy......................................................5-6

 Job build ............................................. ... ... ............5-8

 Tandem copy........................................................5-9

 Covers/inserts.......................................................5-11

 Transparency film with insert sheets....................5-22

 Multi shot ..............................................................5-23

 Book copy............................. ................................5-25

 Card shot

.................................................................

5-26

 Mirror image .........................................................5-28

 B/W reverse..........................................................5-28

 Print menu ............................................................5-29

STORING, USING AND DELETING JOB

PROGRAMS ................................................................5-41

 Storing a job program...........................................5-41

 Calling up a job program ......................................5-42

 Deleting a stored job program ..............................5-42

INTERRUPTING A COPY RUN...................................5-43

CHAPTER 6 MACHINE MAINTENANCE (FOR COPYING)

USER MAINTENANCE................................................6-2

 Cleaning the document glass and the automatic

document feeder...................................................6-2

 Cleaning the main charger of the

photoconductive drum..........................................6-2

TROUBLESHOOTING.................................................6-3

CHAPTER 7 DOCUMENT FILING FUNCTION

OVERVIEW..................................................................7-2

 Document filing function .......................................7-2

TO USE THE DOCUMENT FILING FUNCTION..........7-4

 A look at the operation panel................................7-4

 Saving files ...........................................................7-4

 Main screen of document filing.............................7-5

 Document filing icons ......................... ... ... ............7-5

SAVING A DOCUMENT IMAGE FILE..........................7-6

 Quick File..............................................................7-6

 Filing.....................................................................7-7

 Print jobs...............................................................7-9

 Scan Save ............................................. ... ... .........7-10

CALLING UP AND USING A FILE...............................7-13

 Searching for and calling up a saved file

..............

7-13

 Calling up and using a saved file..........................7-15

CUSTOM SETTINGS............................ .......................7-21

 Creating, editing, and deleting user names and

folders...................................................................7-21

ENTERING CHARACTERS.........................................7-26

TROUBLESHOOTING.................................................7-28

CHAPTER 8 SPECIFICATIONS

SPECIFICATIONS.......................................................8-2

LIST OF COMBINATION OF PERIPHERAL DEVICES..

8-4

INDEX..........................................................................8-5

1-1

CHAPTER 1

BEFORE USING THE

PRODUCT

This chapter contains basic information that should be read before using the product.

Page

INTRODUCTION .................................................................................... 1-2

MAIN FEATURES...................................................................................1-3

PART NAMES AND FUNCTIONS.......................................................... 1 -9



Exterior............................................................................................ 1-9



Interior.............................................................................................1-10



Part names and functions of peripheral devices............................. 1-11



Operation panel............................................................................... 1-13



Touch panel .................................................................................... 1-14

TURNING THE POWER ON AND OFF.................................................. 1-17

AUDITING MODE................................................................................... 1-18



Using the machine when the auditing mode is enabled.................. 1-18

1-2

INTRODUCTION

Thank you for purchasing a Olivetti digital multifunction copier. Please read this manual before using the machine. In particular, be sure to read "INSTALLATION REQUIREMENTS" before using the machine. Please keep this manual close at hand for reference whenever necessary. This manual provides general information on using the machine, such as routine main tenance and how to load paper and remove misfeeds. It also explains how to use the copier and document filing functions. Separate manuals have been provided for the fax function, printer function, and network scanner function.

 Original and paper sizes

This machine allows use of standard sizes in both the AB and inch systems. These are shown in the tables below.

 The meaning of "R" in original and paper size indications

Some original and paper sizes can be placed in either the portrait or landscape orientations. To differentiate between landscape and portrait, the landscape orientation size indication will contain an "R". These are indicated as A4R, B5R, 8-1/2" x 11"R, 5-1/2" x 8-1/2"R, etc. Sizes that can be placed only in the landscape orient ation (A3, B4, 11" x 17", 8-1/2" x 14", 8-1/2" x 13") do not contain the "R" in their size indication.

Sizes in the AB system Sizes in the inch system A3 11" x 17" (LEDGER) B4 8-1/2" x 14" (LEGAL) A4 8-1/2" x 13" (FOOLSCAP) B5 8-1/2" x 11" (LETTER) A5 7-1/4" x 10-1/2" (EXECUTIVE)

5-1/2" x 8-1/2" (INVOICE)

Size indication with "R"

Landscape orientation

Size indication without "R"

Portrait orientation

1-3

MAIN FEATURES

The digital multifunction copier is capable of performing a variety of functions. This page shows features related to the copy function.

● Sort mode See page 1-3

● Group mode See page 1-3

● 2-sided Copy See page 1-3

(When the duplex module is installed.)

● Exposure Adjustments See page 1-3

● Reduction/Enlargement See page 1-4

● XY Zoom See page 1-4

● Margin Shift See page 1-4

● Erase See page 1-4

● Dual Page Copy See page 1-4

● Pamphlet Copy See page 1-4

● Job Build See page 1-5

● Tandem Copy See page 1-5

(Olivetti d-Copia 3501 / d-Copia 4501 version

● Covers/inserts See page 1-5

● Transparency Insert See page 1-5

● Multi Shot See page 1-5

● Book Copy See page 1-5

● Card Shot See page 1-6

● Job programs See page 1-6

● Mirror Image See page 1-6

● B/W Reverse See page 1-6

● Date See page 1-6

● Stamp See page 1-6

● Page numbering See page 1-7

● Text See page 1- 7

● Interrupting a copy run See page 1-7

● Offset mode See page 1-7

(When the Finisher or Saddle stitch finisher is installed.)

● Staple sort mode See page 1-7 (When the Finisher or Saddle stitch finisher is installed.)

● Saddle stitch See page 1-7 (When the Saddle stitch finisher is installed.)

● Hole punching See page 1-8 (When the Saddle stitch finisher and Punch Module are installed.)

● Document filing function See page 1-8 (Olivetti d-Copia 3501/4501 version or when the document filling function has been added.)

Sort mode See page 4-9

Copies can be collated.

Group mode See page 4-9

Copies can be grouped by page.

2-sided Copy See pages 4-10, 4-13

Copy onto both sides of the paper using the document glass or the automatic document feeder.

Exposure Adjustments See page 4-14

The desired image type for the original can be selected.

Original Copy

Original

Copy

* When the duplex module is installed.

Exposure

Text Text/Photo Photo

Resolution

ABCDE

DarkerLighter

or when the document filling function has been added.)

MAIN FEATURES

1-4

Reduction / Enlargement See page 4-15

Copies can be enlarged or reduced to the desired size.

XY Zoom See page 4-18

Separate ratio settings can be selected for the length and width of a copy.

Margin Shift See page 5-3

Margins can be added to copies.

Erase See page 5-4

Shadows that appear around the edges of copies of books or thick originals can be erased.

Dual Page Copy See page 5-5

The left and right pages of a book can be successively copied onto separate sheets.

Pamphlet Copy See page 5-6

One-sided or two-sided pamphlet style copies can be made.

Original

Enlargement Reduction

Copy

Original Copy

Image shifted to the right

Image shifted to the left

Margin

One-sided copying Original

Two-sided copying Original

Image shifted to the right

Margin

Image shifted to the left

Margin

Original

Copy

Edge erase

Centre erase

Edge+Centre

erase

CopyBook original

Finished copies are folded in two.

Originals (one-sided)

Originals (two-sided)

Left binding

Right binding

First page

MAIN FEATURES

1-5

Job Build See page 5-8

When you have a very large number of originals, the pages can be scanned in sets.

Tandem Copy See page 5-9

Two machines can be used to run a large copy job in parallel.

Covers/inserts See page 5-11

Front covers, back covers, and inserts can be added. These can also be copied on.

Transparency Insert See page 5-22

Inserts can be automatically inserted between transparencies.

Multi Shot See page 5-23

Multiple original pages can be copied onto a single sheet of paper in a uniform layout.

Book Copy See page 5-25

Books and other bound originals can be copied pamphlet style.

50 sheets100 sheets 50 sheets

100 sets of

copies

50 sets of

copies

50 sets of

copies

* Olivetti d-Copia 3501 / 4501 version or when the document filling function has been added.

Front cover

Back cover

Originals

Insert sheets

Originals (1-sided)

Originals (2-sided)

Copy

Originals (1-sided)

Originals (2-sided)

Copy

CopyOriginal

Left binding

Right binding

First page

MAIN FEATURES

1-6

Card Shot See page 5-26

The front and back of a card can be copied onto one sheet of paper. This function is convenient for making copies for certification purposes and helps save paper.

Job programs See page 5-41

Various steps of a copy operation can be stored as a program, and up to 10 programs can be stored. Saving frequently used sets of settings in a program saves you the trouble of selecting those settings each time you wish to use them.

Mirror Image See page 5-28

A mirror image copy can be made.

B/W Reverse See page 5-28

White and black can be inverted on a copy to produce a negative image.

Date See page 5-32

The date can be added to copies.

Stamp See page 5-33

Reverse text can be added to copies ("stamp").

Original

Example: Portrait A4 (8-1/2" x 11") size

Example: Landscape A4 (8-1/2" x 11") size

Copy

Back of

card

Front of

card

CARD

JOB PROGRAMS

PRESS PROGRAM NUMBER.

RECALL

Original Copy

2004/OCT/1

CONFIDENTIAL

MAIN FEATURES

1-7

Page numbering See page 5-34

Page numbers can be added to copies.

Text See page 5-38

Entered text can be added to copies.

Interrupting a copy run See page 5-43

A copy job in progress can be interrupted for a rush job.

Offset mode See page 3-8

Each set of output can be offset slightly from other sets for easy separation.

Staple sort mode See page 3-8, 3-16

Sets of copies can be automatically stapled.

Saddle stitch See page 3-14

When a saddle stitch finisher is installed, copies can be automatically folded in half and stapled at the fold. (Use with the pamphlet function (see page 5-6) or book copy function (see page 5-25).)

October, 2004 Meeting

AUTO

ORIGINA

EXPOSUR

INTERRUPT

ORIGINAL

Offset mode Non-Offset mode

*When the Finisher or Saddle stitch finisher is

installed.

Original

Copy

*When the Finisher or Saddle stitch finisher is

installed.

Saddle stitch binding

*When the Saddle stitch finisher is installed.

MAIN FEATURES

1-8

Hole punching See page 3-17

Copies can be punched to add holes.

Document filing function See CHAPTER 7

A document image can be stored on the hard disk. A stored file can easily be called up and printed or transmitted.

Energy saving features

This product has the following two power reducing modes to help conserve natural resources and reduce environmental pollution.

Preheat mode

When the machine remains in the standby state for the amount of time set in the key operator programs, preheat mode automatically reduces the temperature of the fusing unit to save power while the machine is on standby. When a fax or print job is received, or keys are pressed on the operation panel, or an original is placed for a copy, fax, or network scanner job, preheat mode automatically turns off.

Auto power shut-off mode

The auto power shut-off mode is the second level of power reduction. In this mode power is shut off to the fusing unit and the touch panel. In this state more energy is saved than in the preheat mode but the time to recover to the ready condition will be longer. The preset time to enter this mode can be set by a key operator program.

When this product is used as a printer, and either of the above modes is active, the mode will be deactivated automatically by an incoming job and the machine will automatically warm up and start to print when it has reached the ready temperature. When this product is configured for multi-function operation, and either of the above modes is active, the mode will be deactivated as above by an incoming print job. Either mode will also be deactivated by operation of DOCUMENT FILING, IMAGE SEND or COPY mode key.

Original Punch positions

* When the saddle stitch finisher and punch

module are installed.

Save to machine's hard disk

HDD

Document Image

Call up a saved file to reuse

Printed

Transmitted

* Olivetti d-Copia 3501 / 4501 version or when the document filling function has been added.

The ENERGY STAR program is an energy reduction plan introduced by theUnited States Environmental Protection Agency in response to environmental issues and for the purpose of advancing the development and utilization of more energy efficient office equipment.

ENERGY STAR is a U.S. registered mark.

1-9

PART NAMES AND FUNCTIONS

Exterior

(1) Bypass tray*

(2) Exit tray*

(3) Automatic document feeder (See page 4-2.)

This automatically feeds and scans multiple sheet originals. Both sides of two-sided originals can be scanned at once.

(4) Duplex module*

Module for two-sided printing

(5) Upper paper output area (Centre tray)

Finished sheets are deposited here.

(6) Upper exit tray extension*

Provides support for large size paper.

(7) Operation panel

(8) Front cover

Open to add toner.

(9) Power switch

Press to turn power on and off.

(

)Paper tray 1

(11)

Stand/3 x 500 sheet paper drawer*

(12)

Stand/MPD & 2000 sheet paper drawer* (See page 2-11.)

(13)

Multi purpose drawer* (See page 2-8. )

* (1), (2), (4),

(6), (11)

, (12) and

(13)

are peripheral devices. For description of these devices, see page 1-11.

(1) (2) (3) (4) (5) (6) (7) (8) (9) (10)

(11)

(12)

(13)

PART NAMES AND FUNCTIONS

1-10

Interior

(14)Duplex module side cover

Open when a misfeed has occurred in the duplex module.

(

)Side cover latch

Push up to open the side cover when a misfeed has occurred in the main unit.

(

)Fusing unit

Lift up to open the side cover when a misfeed has occurred in the main unit.

(

)Toner cartridge (drum/toner cartridge)

The toner cartridge must be replaced when indicated on the operation panel. (See page 2-15)

(

)Photoconductive drum

Images are formed on the photoconduct ive drum.

(

)Cartridge lock lever

When replacing the drum, toner or developer cartridge, turn down this lever and pull it out.

(14) (15) (16) (17)

(18) (19)

CAUTION

The fusing unit is hot. Take care in removing misfed paper.

NOTE

Do not touch or damage the photoconductive drum.

PART NAMES AND FUNCTIONS

1-11

Part names and functions of peripheral devices

(1) Upper exit tray extension (AR-TE4)

Mount this unit to the upper paper exit tray. This extension is needed to support large size paper.

(2) Finisher (AR-FN6)

Output sheets can either be sorted in page order or grouped by page. Sorted sets or groups are offset stacked for easy separation when removed. Sorted sets can be delivered either stapled or unstapled.

(3) Mail-bin stacker (AR-MS1)

This unit is an output sorter that has seven receiving bins. The bin to receive printed output can be selected in the printer driver. Each bin can be assigned to receive printed output by an individual person or by groups of people so that their prints are separated from other users making them easy to retrieve. When this unit is installed, any copies or facsimile prints will be sent to the top tray and not into the mail bins.

(4) Stand/MPD & 2000 sheet paper drawer (AR-D28)

This paper feed unit contains an upper multipurpose drawer (see item (6)) and a lower drawer which can hold a maximum of 2000 sheets of 80 g/m

(20 lbs.) paper.

(5) Multi purpose drawer (ARMU2)

Up to 500 sheets of 80 g/m

(20 lbs.) paper can be loaded. Also special papers such as envelopes (standard sizes only) and postcards can be set.

(6) Stand/3 x 500 sheet paper drawer (AR-D27)

This paper feed unit contains an upper multipurpose drawer (see item (6)) and two lower drawers each of which can hold a maximum of 500 sheets of 80 g/m

(20 lbs.) paper.

(7) Saddle stitch finisher (AR-FN7)

The saddle stitch finisher can automatically place two staples for centreline binding of paper and fold them along the centreline. An optional punch module is available for installation into the finisher.

(8) Duplex module (AR-DU3)

An optional duplex module must be installed for automatic two-sided printing.

(

)Duplex module/bypass tray (AR-DU4)

This module is basically the same as (9) above with the addition of a manual bypass paper feed unit.

(

)Exit tray (AR-TE3)

Mounted to the paper output port of a duplex module.

(1)

(2)

(6)

(7)

(8)

(9)

(10)

(3)

(4)

(5)

PART NAMES AND FUNCTIONS

1-12

■ Other optional equipment

●Printer server card (AR-NC7)

This is an NIC card (Network Inte rface Card ) that is required to use the network printer and network scanner functions.

●Printer server card (AR-NC8)

This is an NIC card (Network Inte rface Card ) that is required to use the network pr inter and documen t filling functions, and the network scanner function.

●Barcode font kit (AR-PF1)

This kit adds bar code fonts to the machine.

●PS3 expansion kit (AR-PK6)

This kit provides compatibility of PostScript level 3 to the printer.

●Facsimile expansion kit (AR-FX12)

This kit is required to add fax function.

●Network scanner expansion kit (AR-EF3)

This kit is required to add the network scanning feature. The network printer function is required to add on the network scanner function. On models that do not have the network printer function as a standard feature, the printer server card is required.

Some peripheral devices cannot be inst alled together while others ma y require the installation of one or more others to be functional. See page 8-4, "LIST OF COMBINATION OF PERIPHERAL DEVICES". Peripheral devices are basically optional, but some are provided as standard equipment for some models.

 Additional fax memory (8MB) (AR-MM9)



Data security kit ( AR-FR21U, AR-FR22U)

The AR-FR21U is for models that have a hard disk drive, and the and AR-FR22U is for models without a hard disk drive. This kit is used to erase electronic data from the hard disk and memory immediately after a document is printed or transmitted.

●

PART NAMES AND FUNCTIONS

1-13

Operation panel

(1) Touch panel

The machine status, messages and touch k eys are displayed on the panel. The document filing*

copy, network scanner*

, and fax*3 functions are used by switching to the screen for the desired function. See the following page.

(2) Mode select keys and indicators

Use to change modes and the corresponding display on the touch panel.

[DOCUMENT FILING] key

Press to select the document filing mode*

. (See page 7-5.) When the document filing function has not been added, this key is the [PRINT] key. This key is pressed to change to the print mode screen when the printer function has been added.

[IMAGE SEND] key/LINE indicator/DATA indicator

Press to change the display to network scanner mode*

or fax mode*3. (See the "Operation man ual (for network scanner)") a nd "Operation m anual (f or facsimile)".)

[COPY] key

Press to select the copy mode.

(3) PRINT mode indicators

READY indicator

Print data can be received when this indicator is lit.

DATA indicator

Lights up or blinks when print data is being received. Also lights up or blinks when printing is being performed.

(4) [JOB STATUS] key

Press to display the current job status. (See page 1-15.)

(5) [CUSTOM SETTINGS] key

This is used to store, edit, and delete user names and folder names for the document filing function*

, and to configure the key operator programs and printer configuration settings. (See page 7-21)

(6) Numeric keys

Use to enter numeric values for various settings.

(7) [ ] key ([ACC.#-C] key)

This key is used in copy mode, document filing mode*

, network scanner mode*2, and fax mode*3.

(8) [#/P] key

This is used as a program ke y when using the cop y function, and to dial when using the fax function*

(9) [C] key (Clear key)

This key is used in copy mode, document filing mode

*1, network scanner mode*2, and fax mode*3.

(10)

[START] key

Use this key to start copying in copy mode, scan a document in network scanner mode*

, or scan a

document for transmission in fax mode*

(11)

[CA] key (Clear all key)

This key is used in copy mode, document filing mode

*1, network scanner mode*2, and fax mode*3. Use the key to cancel settings and perform an operation from the initial machine state.

*1 When the document filing function has been added. *2 When the network scanner option is installed. *3 When the fax op tion is installed.

(2)

(9)

(6)

(10) (11)

(7)

(1)

(3)

(8)

(4)

(5)

When the document filing function has not been added.

PART NAMES AND FUNCTIONS

1-14

Touch panel

The touch panel screens shown in this manual ar e printed images, and may appear different from the actual screens.

 Using the touch panel

[Example 1]

Items on the touch panel are easily selectable by touching the key associated with the item with a finger. Selection of an item will be accompanied with a beep tone* to confirm

the item was selected. Also, the key area for the item will be highlighted for visual confirmation.

*If a greyed out key is touched, double beeps will

sound.

[Example 2]

Keys which are greyed

out on any screen are

not selectable.

The confirmation beeps can be disabled by a key operator program. (See page 10 of the key operator's guide.)

 Selecting a function

[Example 1]

If a key is highlighted in a setting screen at the time the screen appears, the [OK] key can be pressed to store the selection without further operation.

[Example 2]

A function in the special functions screen is selected by touching the key so that it is highlighted. To cancel the selection, touch the highlighted key once again.

[Example 3]

A corresponding icon representing the feature will appear on the touch panel and on the main screen of the mode selected. If this icon is touched, the setting screen of the function (or

a menu screen) will appear, allowing the settings to be checked or adjusted and the function to be cancelled easily.

JOB QUEUE

COPY

Suzuki

0666211221

003 / 000

010 / 000

SETS / PROG

Beep

tone

1/13

COMPLETE

Copier feature

 Dual page copy  Job bu i l d  Tandem copy  Mirror image  B/W Reverse

PER.

COVER

SETTING

RIGHT

BINDING

LEFT

BINDING

CANCEL OK

DUAL PAGE

COPY

TANDEM

COPY

READY TO SCAN FOR COPY.

SPECIAL MODES

2-SIDED COPY

OUTPUT

QUICK FILE

FILE

PART NAMES AND FUNCTIONS

1-15

■ Job status screen (common to print, copy, fax, network scan and Internet fax)

This screen is displayed when the [JOB STATUS] key on the operation panel is pressed. This screen can be used to display the "JOB QUEUE" (showing stored jobs and the current job) or the "COMPLETE" job list (showing finished jo bs). This screen can be used to chec k job s, interrupt a job in prog ress to perform another job, and cancel a job.

(1) Job list

The displayed jobs in the job list are themselves operation keys. To cancel printing or to give a job the highest print priority, touch the relevant job k ey to select the job and execute the desired operation using the keys described in (8) and (9). This shows the current job and the jobs waiting to be run. The icons to the left of the jobs in the queue show the job mode. The document filing reprint job icon is highlighted. Note that the icon does not become highlighted during retransmission of a fax/image transmission job.

*1 "PAPER EMPTY" in the job status display

When a job status display indicates "PAPER EMPTY", the specified paper size for the job is not loaded in any of the trays. In this case, the job will be suspended until the required paper is loaded. Other stored jobs will be printed (if possible) until the required paper is loaded. (Other jobs will not be printed if the paper runs out during printing.) If you need to change the paper size because the specified paper size is not available, touch the current job key to select it and then touch the [DETAIL] key described in (10).

(2) Mode select key

This switches the job list display between "JOB QUEUE" and "COMPLETE".

"JOB QUEUE": Shows stored jobs and the job in

progress.

"COMPLETE": Shows finished jobs.

Files saved using the "FILE"

*2 and "QUICK

FILE"

*2 functions and finished broadcast transmission jobs appear as keys in the finished job screen. The "FILE"

*2 or "QUICK FILE"

*2 job keys in the finished job screen can be touched, followed by the [CALL] key

*2, to call up a finished job and print or transmit it. A finished broadcast transmission job key can be touched followed by the [DETAIL] key to check the result of the transmission.

Can only be used on the d-Copia 3501/4501

version

, or when the document filling function

has been added.

JOB QUEUE

COPY

Suzuki

066211221

STATUS

020 / 001

020 / 000

002 / 000

PRINT JOB

E-MAIL/FTP

FAX JOB

INTERNET-FAX

JOB QUEUE

COMPLETE

JOB QUEUE

COMPLETE

DETAIL

PRIORITY

STOP/DELETE

DETAIL

CALL

PAPER EMPTY

WAITING

1/1

SETS / PROGRESS

COPYING

"JOB QUEUE" screen

"COMPLETE" job screen

(1)

(2)

(3) (4) (5) (6) (7) (8) (9)(10) (11)

Print mode Copy mode

Scan to e-mail job

Scan to FTP job

Scan to Desktop job

Fax send job Fax reception job

PC-Fax send job

i-Fax send job

i-Fax reception job

PC-Internet Fax send job

Internet Fax mode

E-MAIL/FTP mode

Fax mode

PART NAMES AND FUNCTIONS

1-16

(3) [PRINT JOB] key

This displays the print job list of print mode (copying, printing, fax reception, Internet fax reception, and self printing).

(4) [E-MAIL/FTP] key

This displays the transmission status and finished jobs of scan mode (Scan to e-mail, Scan to FTP, and Scan to Desktop) when the network scanner option is installed.

(5) [FAX JOB] key

This displays the transmission/reception status and finished jobs of fax mode (fax and PC-Fax) when the fax option is installed.

(6) Display switching keys

Use to switch the page of the displayed job list.

(7) [INTERNET-FAX] key

This displays the transmission/reception status and finished jobs of Internet fax mode and PC Internet fax mode when the network scanner option is installed.

(8) [STOP/DELETE] key

Use to cancel or delete the current job or delete the stored job. Note that printing of received faxes and received Internet faxes cannot be cancelled or deleted.

(9) [PRIORITY] key

Touch this key after selecting a stored job in this [JOB QUEUE] list to print the job ahead of the other jobs. Note that a job in progress cannot be interrupted if it is an interrupt copy job or if it is a list print job.

(10)

[DETAIL] key

This shows detailed information on the selected job.

Files saved using the "FILE"

*2 and "QUICK

FILE"

*2 functions and finished broadcast

transmission jobs

appear as keys in the finished job screen. A Quick File in the finished job screen or the [Filing] key*

can be touched, followed by the

[CALL] key*

, to call up a finished job and print or transmit it. A finished broadcast transmission job key can be touched followed by the [D ETAIL] key to check the result of the transmission.

(11)

[CALL] key

When this key is touched after selecting a job in the COMPLETE job status screen (a job stored using the FILE or QUICK FILE keys of the document filing function), the "JOB SETTINGS" menu screen appears to let you resend or reprint the finished job. (See "Document filing function" on page 7-2.)

2 Can only be used on the Olivetti d-Copia 3501 / 4501 version or when the document filling function has been added.

1-17

TURNING THE PO WER ON AND OFF

Use the power switch on the front of the machine to turn the power on or off.

Power switch

"OFF" position

"ON" position

CAUTION

Before turning off the main power switch, make sure that the communication and data indicators are not blinking on the operation panel. Turning off the main power switch or unplugging the power cord while the lights are blinking may damage the hard disk and cause the data being stored or received to be lost.

NOTES

 Turn both switches off and unplug the power cord if you suspect a machine failure, if there is a bad thunderstorm

nearby, or when you are moving the machine.

 If the fax function has been added, always keep the fax po wer switch turned on. Faxes cannot be received if the

fax power switch is turned off. (Faxes can be received when the main power switch is turned off.)

1-18

AUDITING MODE

Auditing mode can be enabled to keep track of the number of pages printed and tran smitte d (scanned) b y eac h account (up to 500 accounts can be established). The page counts can be viewed and totaled as needed. <This mode is enabled in the key operator programs separately for the copy, printer, fax, Internet fax, network scanner, document filing functions. (Page 7 of the key operator's guide)>

Using the machine when the auditing mode is enabled

The procedure for making copies when auditing mode has been enabled for the copy function is explained below.

When the auditing mode is turned on, the right message appears on the touch panel.

When the above screen appears, enter your 5-digit account number and then begin the copying procedure.

Enter your account number (5 digits) with the numeric keys.

As you enter your account number, the hyphens (-) change to asterisks ( ). If you enter an incorrect digit, press the [C] (Clear) key and re-enter the correct

digit. When a correct account number is entered, the

following message will appear.

If a limit has been set by a key operator program for the number of copies that can be made by the account, the remaining number that can be made is displayed.

Check the number in the display and touch the [OK] key.

Follow the appropriate steps to perform the copy job.

When copying is begun, the following message will appear.

To perform an interrupt copy job (page 5-43), touch the [INTERRUPT] key and then enter your account number as explained in step 1. The following message will appear.

When the copy job is finished, press the [ ] key ([ACC.#-C] key)

NOTES



When auditing mode is enabled for document filing and fax/image transmission, a message will appear asking you to enter your account number each time you switch to the main screen of one of those functio ns in the touch panel. Enter your account number in the same way as for copy mode, and then begin the scanning procedure.



When the a

ccount counter is turned on for the printer function, you must enter your account number in the setting screen

of the printer driver on your computer in order to print.

ENTER YOUR ACCOUNT NUMBER.

NOTE

If "ACCOUNT NUMBER SECURITY" is enabled in the key operator programs and an incorrect account number is entered three times in a row, "PLEASE SEE YOUR KEY OPERATOR FOR ASSISTANCE." will appear. (Page 8 of the key operator's guide.) Operation is not possible while this message appears (about one minute).

ACCOUNT STATUS :MADE /REMAINING COPIES :00,123,000/00,012,456

READY TO SCAN FOR COPY. PRESS [ACC.#-C] WHEN FINISHED.

COPY INTERRUPT MODE. READY TO SCAN FOR COPY.

+ 158 hidden pages