Oliso TG1100 User Manual [fr]

User Manual Manuel de l’utilisateur
SAVE THESE INSTRUCTIONS
CONSERVEZ CES INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
When using your iron, basic safety precautions should always be followed, including the following:
1 ) Use iron only for its intended use. 2 ) To protect against a risk of electric shock, do not immerse the iron in water or other liquids. 3 ) The iron should always be turned to “Off” before plugging or unplugging from the outlet. Never tug cord to disconnect from the outlet; instead, grasp plug and pull to disconnect. 4 ) Do not allow cord to touch hot surfaces. Let iron cool completely before putting away. Loop cord loosely around iron when storing. 5 ) Always disconnect iron from electrical outlet when filling with water or emptying and when not in use. 6 ) Do not operate iron with a damaged cord or if the iron has been dropped or damaged. To avoid the risk of electric shock, do not disassemble the iron. Take it to a qualified serviceman for examination and repair. Incorrect reassembly can cause a risk of electric shock when the iron is used. 7 ) Do not allow children to use iron. Close supervision is necessary for any appliance being used near children. Do not leave iron unattended while connected or on an ironing board. 8 ) Burns can occur from touching hot metal parts, hot water, or steam. Use caution when you turn a steam iron upside down – there may be hot water in the reservoir. 9 ) If the LED flashes orange (not red or green), the iron is not operating normally. Disconnect from the power supply and have the iron serviced by qualified service personnel.
Read all instructions before using this product.
SPECIAL INSTRUCTIONS
1 ) The iron must be used on a stable surface. When placing the iron on a stand or resting surface, make sure the stand or surface is stable. 2 ) Oliso irons are high wattage appliances: The EU version is 2000-2400W at 220-240V. The US and Canada versions are 1600W at 120V for models TG1050, 1800W at 125V for models TG1100, TG1250, and TG1600. To avoid a circuit overload, do not operate another high wattage appliance on the same circuit. 3 ) If an extension cord is absolutely necessary, a 15A cord should be used. Cords rated for less amperage may overheat. Care should be taken to arrange the cord so that it cannot be pulled or tripped over.
4) This iron uses hot steam!
5) Never direct fill the iron from a water tap while the iron is plugged into a power source.
6) FOR HOUSEHOLD USE ONLY
3 Simple Steps To Start
iTouch™ Technology
1
2
3
FILL UNPLUGGED
Open the Flip Funnel™ and add water to the tank with the fill cup or directly from a faucet.
Note: 2 fill cups equal the max capacity of the water tank.
SET UP
Plug in, then choose a fabric and steam settings.
IRON
When the green light stops blinking and is solid, the iron is ready for use. Touch the handle and begin using.
To operate, place the iron, soleplate down, on a flat surface. Plug the iron into an outlet and make sure the iTouch™ switch is in the ON position.
Simply touch the iron handle, and the iron will sense your hand and lower. Let it go, and the iron’s scorch guards will automatically raise the iron above the fabric.
OFF ON
As a safety precaution, when iTouch™ is deactivated, if the soleplate is left face down for more than 30 seconds, the scorch guards will automatically lift the iron off fabric, preventing scorching and burns. For more information regarding the auto shut-off safety feature, see page 4.
DEACTIVATING THE ITOUCH™ TECHNOLOGY
If you wish to deactivate the iTouch™ feature, set the switch on the back of the iron to the OFF position. The iron will function like a standard iron. If you wish to reactivate the iTouch™ feature, set the switch back to the ON position.
ENGLISH
1
Getting To Know Your Oliso® Smart Iron™
1 2
3 4
5
6
7
8
9
10 11
12
Water Tank
Before filling, slide the steam selector to off ( ). Make sure the iron is
unplugged.
Open the Flip Funnel™.
Alternatively, fill directly from a faucet holding the iron horizontally. Do not fill the tank past the MAX fill line on the side of the iron. Close the port when done.
If you need to add water during ironing, unplug the iron and repeat the above steps. After filling, make sure the iron is fully reheated before ironing.
1. Status Light
2. Steam Burst
3. Spray Mist
4. Steam Selector
5. Fabric Selector
6. Spray Nozzle
7. Detailer
2
13
8. iTouch™ Handle
9. iTouch™ over-ride
Flip Funnel
10.
11. Water Tank
12. Soleplate
13. Scorch Guards
Leave the iron in a horizontal position and fill using the included fill cup. Two fill cups equal the maximum capacity of the water tank.
WATER RECOMMENDATIONS
This iron is designed to be used with regular tap water. If your water is over 12 grams of hardness, we recommend using either inexpensive bottled spring water or mixing half tap water with half distilled water.
Never use 100% distilled water as this can cause the iron to spit and leak.
Fabric Selector
FABRIC SELECTOR
FABRIC SELECTOR
STATUS LIGHT
Extreme Steam Triple Play
Steam Selector: Slide the steam selector
to set the amount of continuous steam. The iron can only produce steam when the fabric selector knob is set to the wool ( •• ), cotton, or linen range (•••). Allow the iron to heat up (solid green status light) before activating the steam control. Steam will be produced as soon as the iron is lowered. Steam will stop when iron lifts up.
Dry Ironing: To turn off the steam, slide the steam selector off ( ).
Zero-Drip: The Oliso® Smart Iron™ has a zero-drip feature which
shuts off steam any time the iron’s scorch guards are extended.
ENGLISH
dry ironing
steam okay
Turn the fabric selector to select a fabric setting. To use continous steam or steam burst, the temperature must be set to the wool, cotton, or linen range.
STATUS LIGHT
red flashing green
optimizing
off
temperature
solid green
ready
flashing red
auto off
The Oliso® iron uses a status light to display the iron’s status. To ensure correct temperature, wait until the light displays solid green before ironing.
1. Spray
• Press spray button for spray mist
• Spray will help remove wrinkles
2. Burst of Steam
• Press steam button for a strong
burst of steam from the soleplate.
• Steam button can only be used
when the iron is heated to the wool (••), cotton, or linen range (•••).
• Wait at least 3 seconds between
each press of steam button.
3. Vertical Steam
• Press the steam button while
holding the iron upright.
• Use to get creases and wrinkles
out of hanging clothes or curtains.
• Wait at least 3 seconds between
each press of steam button.
1
2
3
3
Loading...
+ 11 hidden pages