Page 1
_____________________________________________________________________________________________
OPERATING MANUAL
Before attempting to connect or operate this product, please read these
instructions completely
ON-SCREEN-DISPLAY
Optical Low Pass Filter (OLPF) Switching Mechanism
CCD ZOOM CAMERA
SZX23-1480 NTSC
SZX23-1480P PAL
12V DC
WARNING:
TO REDUCETHE RISK OF FIRE OR ELECTRONIC SHOCK,
DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE
AND DO NOT REMOVE COVER OR BACK.
CAUTION:
1. CONNECT 24VAC UL LISTED CLASS 2 POWER SUPPLY.
2. INSTALL CAMERA UNDER UNSTABLE LIGHT SOURCE MAY
CAUSE ABNORMAL FUNCTION.
3. ONLY USE CAMERA UNDER CONDITIONS WHERE
TWMPERA TURES ARE BETWEEN
FIELS INSTALLATION MARKING:
INSTALLATION SHOULD BE MADE BY A QUALIFIED
-10°C to 50°C.
SERVICE PERSON AND SHOULD CONFORM TO ALL LOCAL
CODES
Page 2
______________________________________________________________________
1. General
This camera features a new Ultra Super high sensitive Near Infra-red CCD sensor
and the combination of special optical and digital electronic processing circuit,
deliver a high resolution, sharp, crisp image at daytime, and a clear monochrome
picture under low light or minimal IR projection. This superior and high sensitive
series ensure to meet any strike 24 hour’s surveillance monitoring demand. This
color CCD video camera employs a 1/4 inch charge coupled device solid-state
imaging device with 470/410 k (hi- res.) picture elements, a 23x optical zoom lens,
a 10x digital zoom, and external sync function. This unit is equipped with a newly
developed DSP (Digital Signal Processor) for video signal process. A
micro-controller is also introduced to provide excellent color reproduction, sharp,
stable picture and most of the function’s control; The special for this camera is it
has more than 4 times sensitivity on NIR range and 2 times on visible light range
compare to conventional camera.
2. Features…………………………… ………………………
1. Easy recognize the objects under extreme low light.
2. Accept minimal IR illumination for completely dark surveillance for excellent
picture quality.
3. Daytime color and auto switchover to black-white picture at night (IR filter
removable).
4. 480 lines of horizontal resolution and high quality picture by utilizing digital
processing LSI’s
5. 230x zoom (23x optical & 10x digital zoom).
6. Minimum illumination of 0.5Lux (F1.2, Target) and signal-to-noise ratio of 50
dB is realized by employing an extra high sensitivity image sensor with micro
lenses and low noise circuit design.
7. High quality picture –A digital signal processor (DSP) performs digital
horizontal and vertical aperture enhancement to produce high-resolution
picture.
8. A newly developed intelligent wide range Auto Tracing White Balance (ATW)
that automatically adjusts the white balance according to the color
temperature of the light source illuminating the subject.
9. Smart digital control Auto BLC.
10. Advanced Auto Exposure System for both fix iris and auto iris lenses control
the amount of light to ensure it is always optimized.
11. Internal or Line-lock external sync.
12. Long life and high reliability.
- 1 -
Page 3
______________________________________________________________________
3. Major Control And Their Function--
109.5
123.5
C
70
D
1
63.6
DC12V
WIDE
+
-
TELE
FZRS485D0
I
03 1211100908070605040201
0
5
4
3
2
NEARFAR
1
PROTOCOL
PL
DI
VIDEO OUT
E
G
H
F
36.4
A. Holder screw hole
The mounting hole is a standard photographic pan-head screw size
(1/4” – 20)
B. DC12V Block Terminal
This terminal accepts DC12V Please add + & - to power terminals drawing
C. Zoom adjustment ( WIDE / TELE )
230X
COLOR CCD CAMERA
DIGITAL ZOOM
A
B
DC 12V
D. Focus adjustment ( FAR / NEAR )
E. Protocol select DIP Switch
F. Video output terminal (BNC)
This connector is used to connect with the VIDEO IN connector of monitor.
G. Power LED
H. Screwless type terminal 12 pin (Remote).
I. On-Screen Display keypad (UP / DOWN / ENTER / ESC)
J. Filter holder(M30.5 x 0.5mm)
4. User OSD Setting Menu and Functions-----
[UP]
[DOWN]
[ENTER]
[ESC]
Push [ENTER] key 3 sec. to get into the OSD menu.
Push [ESC] key to leave menu.
If pushed [ESC] key, all set parameter data will be saved and return back to the previous menu page, this will occur while
setting the parameter and without push [ENTER] key.
：
UP & RIGHT MOVE KEY
：
DOWN & LEFT MOVE KEY
：
ENTER KEY
：
ESC KEY
- 2 -
Page 4
______________________________________________________________________
SETUP MENU [1/5]
CAMERA ID ON
SENSE UP x4
AISHUT AUTO.
AES FIX.
BLC OFF
AGC +4
Page1 MAIN MENU Page2 MAIN MENU
SETUP MENU [3/5]
POSITION LOAD.
H-GAIN +6
V-GAIN +6
MOTION OFF
IR ON.
INITIAL ON
Page3 MAIN MENU Page4 MAIN MENU
SETUP MENU [5/5]
ZOOM+AF OFF
AF SLEEP OFF
SCALE OFF
LANGUAGE ENGLISH
WINKER OFF
MISC
Page 5 MAIN MENU
4.1 Camera Identification Setting (CAMERA ID)
SETUP MENU [1/5]
CAMERA ID →ON.
SENSE UP x4
AISHUT AUTO.
AES FIX.
BLC OFF
AGC +4
CAMERA ID
EDIT
POSITION L-U
↓
- - - - - - - - - - - - - - - - - - - -
CAMERA ID
EDIT
POSITION L-U
↓
- - - - - - - - - - - - - - - - - - - -
Move cursor to CAMERA ID, press ENTER key to enter ID FUNCTION SELECTING
menu, then Press UP or DOWN key to select ON.
Press ENTER key to enter CAMERA ID EDIT menu.
Page1 MAIN MENU
Press ENTER key to edit ID character, and then press UP or DOWN key to select ID
character position (total twenty character positions).
Press ENTER key to enter ID characters menu.
CAMERA ID EDIT MENU
Select the desired character by using UP and DOWN button, and Press ENTER key
to confirm the blinking character .The first character is saved and the cursor in the
button of the screen moves to next (Maximum 20 characters).
SETUP MENU [2/5]
WHITE BAL ATW.
SYNC OFF
ZOOM
DIGITAL ZOOM OFF
FOCUS
AUTO FOCUS OFF
SETUP MENU [4/5]
DEFAULT CANCEL
FREEZE OFF
FREEZE MODE FIELD
ZOOM SPEED +3
FOCUS SPEED MIN
GAMMA GAMMA1
- 3 -
Page 5
______________________________________________________________________
ID CHARACTER MENU
CAMERA ID
EDIT
→POSITION L-U
- - - - - - - - - - - - - - - - - - - -
4.2 SENSE UP
SETUP MENU [1/5]
CAMERA ID ON
SENSE UP →x4
AISHUT AUTO.
AES FIX.
BLC OFF
AGC +4
4.3 AISHUT (Auto Iris)
4.3.1 AISHUT AUTO MODE
SETUP MENU [1/5]
CAMERA ID ON
SENSE UP x4
AISHUT →AUTO.
AES FIX.
BLC OFF
AGC +4
AISHUT
AUTO LEVEL →+4
4.3.2AISHUT FIX MODE
SETUP MENU [1/5]
CAMERA ID ON
SENSE UP x4
AISHUT →FIX.
AES FIX.
BLC OFF
AGC +4
Move cursor to POSITION, press ENTER key to enter ID POSITION SELECTING
menu, then Press UP or DOWN key to select ID POSTION L-U, R-D, L-D or R-U.
CAMERA ID EDIT MENU
Move cursor to SENSE UP, press ENTER key to enter SENSE UP FUNCTION
SELECTING menu, then Press UP or DOWN key to select OFF, x2, x4, x6, x8, x12, x16,
x32 or x64 (0 Frame, 2 Frames, 4 Frames, 6 Frames, 8 Frames, 12 Frames, 16 Frames,
32 Frames, 64 Frames, 9 steps adjustable).
Page1 MAIN MENU
Move cursor to AISHUT, press ENTER key to enter AISHUT FUNCTION SELECTING
menu, then Press UP or DOWN key to select AUTO.
Press ENTER key to enter AUTO LEVEL ADJUSTMENT menu.
Page1 MAIN MENU
Press ENTER key to enter AUTO LEVEL SELECTING menu, then Press UP or DOWN
key to select MIN, +1, +2, +3, +4, +5, +6, +7, MAX.
AUTO LEVEL ADJUSTMENT MENU
Move cursor to AISHUT, press ENTER key to enter AISHUT FUNCTION SELECTING
menu, then Press UP or DOWN key to select FIX.
Press ENTER key to enter FIX LEVEL ADJUSTMENT menu.
Page1 MAIN MENU
- 4 -
Page 6
______________________________________________________________________
AISHUT
FIX LEVEL →+4
FIX LEVEL ADJUSTMENT MENU
4.4 AES (Auto Exposure Mode)
4.4.1 AES FIX MODE
SETUP MENU [1/5]
CAMERA ID ON
SENSE UP x4
AISHUT AUTO.
AES →FIX.
BLC OFF
AGC +4
AES
FIX LEVEL →OFF
4.4.2 AES AUTO MODE
SETUP MENU [1/5]
CAMERA ID OFF
SENSE UP OFF
AISHUT AUTO.
AES →AUTO.
BLC OFF
AGC +4
AES
AUTO LEVEL →+4
4.5 BLC (Backlight Compensation)
SETUP MENU [1/5]
CAMERA ID ON
SENSE UP x4
AISHUT AUTO.
AES AUTO.
BLC →ON.
AGC +4
Press ENTER key to enter FIX LEVEL SELECTING menu, then Press UP or DOWN key
to select MIN, +1, +2, +3, +4, +5, +6, +7, MAX.
Move cursor to AES, press ENTER key to enter AES FUNCTION SELECTING menu,
then Press UP or DOWN key to select FIX.
Press ENTER key to enter FIX LEVEL ADJUSTMENT menu.
Page1 MAIN MENU
Press ENTER key to enter FIX LEVEL SELECTING menu, then Press UP or DOWN key
to select OFF, 1/100, 1/250, 1/500, 1/1000, 1/2000, 1/4000 or 1/10000.
FIX LEVEL ADJUSTMENT MENU
Move cursor to AES, press ENTER key to enter AES FUNCTION SELECTING menu,
then Press UP or DOWN key to select AUTO.
Press ENTER key to enter AUTO LEVEL ADJUSTMENT menu.
Page1 MAIN MENU
Press ENTER key to enter AUTO LEVEL SELECTING menu, then Press UP or DOWN
key to select MIN, +1, +2, +3, +4, +5, +6, +7, MAX.
AUTO LEVEL ADJUSTMENT MENU
Move cursor to BLC, press ENTER key to enter BLC FUNCTION SELECTING menu,
then Press UP or DOWN key to select ON.
Press ENTER key to enter BLC AREAS AND LEVEL ADJUSTMENT menu.
Page1 MAIN MENU
- 5 -
Page 7
______________________________________________________________________
BLC
→BLC AREA
BLC LEVEL MIN
Press ENTER key to set BLC AREA BLOCK. Press UP or DOWN key to select BLC AREA BLOCK.
OPD WINDOW
This method is suited for cases where the main subject is fixed within the screen.
The important object in a scene is usually placed in the center of the monitor’s screen. In this mode more photometric
weight is given to the center of the screen than to the edge of the picture, this function will eliminate the interference by
strong background light, which makes the camera picture dark. The size and location of center window can be adjusted
freely by user within 48 areas on screen.
BLC
BLC AREA
BLC LEVEL →MIN
4.6 AGC (Auto Gain Control)
SETUP MENU [1/5]
CAMERA ID ON
SENSE UP x4
AISHUT AUTO.
AES FIX.
BLC OFF
AGC →+4
4.7 WHITE BALANCE
4.7.1 ATW (Auto Trace White Balance)
SETUP MENU [2/5]
WHITE BAL →ATW.
SYNC OFF
ZOOM
DIGITAL ZOOM OFF
FOCUS
AUTO FOCUS OFF
Press ENTER key to enter BLC AREA ADJUSTMENT menu.
AREA AND LEVEL ADJUSTMENT MENU
Press ENTER key to enter BLC LEVEL ADJUSTMENT menu, then Press UP or DOWN
key to select MIN, +1, +2, +3, +4, +5, +6, MAX.
Move cursor to AGC, press ENTER key to enter AGC LEVEL SELECTING menu, then
Press UP or DOWN key to select BASE, +1, +2, +3, +4, +5, +6, +7, MAX (0dB ~ 36dB, 9
steps adjustable).
AGC ADJUSTMENT MENU
Move cursor to WHITE BAL, press ENTER key to enter WHITE BAL FUNCTION
SELECTING menu, then Press UP or DOWN key to select ATW.
Press ENTER key to enter ATW LEVEL ADJUSTMENT menu.
- 6 -
Page 8
______________________________________________________________________
Y
Y
Y
Page 2 MAIN MENU
ATW LEVEL
ATW LEVEL →MIDDLE
R-
GAIN +4
B-Y GAIN +4
ATW LEVEL
ATW LEVEL MIDDLE
R-Y GAIN →+4
B-Y GAIN +4
ATW LEVEL
ATW LEVEL MIDDLE
R-
GAIN +4
B-Y GAIN →+4
Press ENTER key to enter ATW LEVEL ADJUSTMENT menu, then Press UP or DOWN
key to select RED, RED+, RED++, RED+++, MIDDLE, BLUE, BLUE+,
BLUE++,BLUE+++, 9 steps adjustable.
Move cursor to R-Y GAIN, press ENTER key to enter R-Y GAIN ADJUSTMENT menu,
then Press UP or DOWN key to select MIN, +1, +2, +3, +4, +5, +6, +7, MAX, 9 steps
adjustable.
Move cursor to B-Y GAIN, press ENTER key to enter B-Y GAIN ADJUSTMENT menu,
then Press UP or DOWN key to select MIN, +1, +2, +3, +4, +5, +6, +7, MAX, 9 steps
adjustable.
4.7.2 AWB (Auto White Balance)
SETUP MENU [2/5]
WHITE BAL →AWB.
SYNC OFF
ZOOM
DIGITAL ZOOM OFF
FOCUS
AUTO FOCUS OFF
AWB LEVEL
AWB LEVEL →MIDDLE
GAIN +4
R-
B-Y GAIN +4
AWB LEVEL
AWB LEVEL MIDDLE
R-Y GAIN →+4
B-Y GAIN +4
Move cursor to WHITE BAL, press ENTER key to enter WHITE BAL FUNCTION
SELECTING menu, then Press UP or DOWN key to select AWB.
Press ENTER key to enter AWB LEVEL ADJUSTMENT menu.
Press ENTER key to enter AWB LEVEL ADJUSTMENT menu, then Press UP or
DOWN key to select RED, RED+, RED++, RED+++, MIDDLE, BLUE, BLUE+, BLUE++,
BLUE+++, 9 steps adjustable.
Move cursor to R-Y GAIN, press ENTER key to enter R-Y GAIN ADJUSTMENT menu,
then Press UP or DOWN key to select MIN, +1, +2, +3, +4, +5, +6, +7, MAX, 9 steps
adjustable.
ATW LEVEL ADJUSTMENT MENU
R-Y GAIN ADJUSTMENT MENU
R-Y GAIN ADJUSTMENT MENU
Page 2 MAIN MENU
AWB LEVEL ADJUSTMENT MENU
- 7 -
Page 9
______________________________________________________________________
Y
R-Y GAIN ADJUSTMENT MENU
AWB LEVEL
AWB LEVEL MIDDLE
R-
GAIN +4
B-Y GAIN →+4
4.8 SYNC
SETUP MENU [2/5]
WHITE BAL AWB.
SYNC →OFF
ZOOM
DIGITAL ZOOM OFF
FOCUS
AUTO FOCUS OFF
4.9 ZOOM
SETUP MENU [2/5]
WHITE BAL AWB.
SYNC OFF
→ZOOM
DIGITAL ZOOM OFF
FOCUS
AUTO FOCUS OFF
ZOOM
WIDE - - - - - - - - - - - TELE
4.10 DIGITAL ZOOM
SETUP MENU [2/5]
WHITE BAL AWB.
SYNC OFF
ZOOM
DIGITAL ZOOM →ON
FOCUS
AUTO FOCUS OFF
Page 2 MAIN MENU
Move cursor to B-Y GAIN, press ENTER key to enter B-Y GAIN ADJUSTMENT menu,
then Press UP or DOWN key to select MIN, +1, +2, +3, +4, +5, +6, +7, MAX, 9 steps
adjustable.
R-Y GAIN ADJUSTMENT MENU
This function is used to adjust phase of external sync.
When input external sync, we can press ENTER key to set SYNC ON, then press UP
or DOWN key to adjust phase.
Page 2 MAIN MENU
Move cursor to ZOOM, press ENTER key to enter ZOOM ADJUSTMENT menu.
Page 2 MAIN MENU
Press UP or DOWN key to select ZOOM WIDE to TELE, 1 to 23 times adjustable.
ZOOM ADJUSTMENT MENU
Move cursor to DIGITAL ZOOM, press ENTER key to enter DIGITAL ZOOM
FUNCTION SELECTING menu.
Press UP or DOWN key to select DIGITAL ZOOM ON or OFF (1 to 10 times
adjustable).
- 8 -
Page 10
______________________________________________________________________
4.11 FOCUS
SETUP MENU [2/5]
WHITE BAL AWB.
SYNC OFF
ZOOM
DIGITAL ZOOM OFF
→FOCUS
AUTO FOCUS OFF
Page 2 MAIN MENU
FOCUS
FAR - - - - - - - - - - - NEAR
Move cursor to FOCUS, press ENTER key to enter FOCUS ADJUSTMENT menu.
Press UP or DOWN key to select FOCUS FAR to NEAR.
FOCUS ADJUSTMENT MENU
4.12 AUTO FOCUS
Move cursor to AUTO FOCUS, press ENTER key to enter AUTO FOCUS FUNCTION
SETUP MENU [2/5]
WHITE BAL AWB.
SYNC OFF
ZOOM
DIGITAL ZOOM OFF
FOCUS
AUTO FOCUS →ON
SELECTING menu.
Press UP or DOWN key to select AUTO FOCUS ON or OFF.
Page 2 MAIN MENU
4.13 POSITION
Move cursor to POSITION, press ENTER key to enter POSITION FUNCTION
SETUP MENU [3/5]
POSITION →LOAD.
H-GAIN +6
V-GAIN +6
MOTION OFF
IR ON.
INITIAL ON
Page3 MAIN MENU
POSITION SAVE
POSITION SAVE →1
SELECTING menu.
Press UP or DOWN key to select LOAD, SAVE, ALARM, and OSD.
There have 64 steps (position with zoom & focus) can be programmed.
After adjusting position with zoom & focus, Press ENTER key to enter POSITION
SAVE SELECTNG menu.
Press UP or DOWN key to select position (1 to 64 position that you want to save),
then press ENTER key that will be saved.
POSITION SAVE MENU
- 9 -
Page 11
______________________________________________________________________
POSITION LOAD
POSITION LOAD →1
ALARM POSITION
ALARM POSITION →OFF
POSITION OSD
OSD →OFF
POSITION R-U
4.14 H-GAIN
This is used to enhance the compensation of the picture quality.
H-GAIN: Horizontal Compensation
SETUP MENU [3/5]
POSITION LOAD.
H-GAIN →+6
V-GAIN +6
MOTION OFF
IR ON.
INITIAL ON
4.15 V-GAIN
This is used to enhance the compensation of the picture quality.
V-GAIN: Vertical Compensation
SETUP MENU [3/5]
POSITION LOAD.
H-GAIN +6
V-GAIN →+6
MOTION OFF
IR ON.
INITIAL ON
Press ENTER key to enter POSITION LOAD SELECTNG menu. Press UP or DOWN
key to select position (1 to 64 position that you want to LOAD), then press ENTER
key that will be loaded.
POSITION LOAD MENU
Press ENTER key to enter ALARM POSITION SELECTNG menu.
Press UP or DOWN key to select alarm position (OFF, 1 to 64 position that you want
to set), then press ENTER key that will be set.
When input alarm signal, alarm position will be loaded.
ALARM POSITION MENU
Display position number.
OSD set ON, position number will be display on right-up(R-U) or right-down(R-D) of
the screen.
POSITION OSD MENU
Move cursor to H-GAIN, press ENTER key to enter H-GAIN ADJUSTMENT menu.
Press UP or DOWN key to select MIN, +1, +2, +3, +4, +5, +6, +7, +8, +9, +11, MAX, 13
steps adjustable.
Page 3 MAIN MENU
Move cursor to V-GAIN, press ENTER key to enter V-GAIN ADJUSTMENT menu.
Press UP or DOWN key to select MIN, +1, +2, +3, +4, +5, +6, +7, +8, +9, +11, MAX, 13
steps adjustable.
- 10 -
Page 12
______________________________________________________________________
Page 3 MAIN MENU
4.16 MOTION
MOTION DETECTION FUNCTION
SETUP MENU [3/5]
POSITION LOAD.
H-GAIN +6
V-GAIN +6
MOTION →ON.
IR ON.
INITIAL ON
MOTION
→AREA
LEVEL +4
TIME 30sec
OSD OFF
IR FILTER REMOVABLE FUNTION (DAY & NIGHT FUNCTION)
SETUP MENU [3/5]
POSITION LOAD.
H-GAIN +6
V-GAIN +6
MOTION ON.
IR →ON.
INITIAL ON
IR SW
IR SW →INT.
IR SW INT. MENU
IR INT LEVEL
IR INT LEVEL →MAX
Move cursor to MOTION, press ENTER key to enter MOTION ON/OFF menu.
Press UP or DOWN key to select ON.
Page 3 MAIN MENU
Press ENTER key to enter MOTION FUNCTION menu.
Press UP or DOWN key to select motion detection AREA, LEVEL (Sensitivity), TIME,
OSD.
When detecting motion, it will output alarm signal.
MOTION MENU
4.17 IR
Move cursor to IR, press ENTER key to enter IR ON/OFF menu.
Press UP or DOWN key to select ON.
Page 3 MAIN MENU
Press ENTER key to enter IR SW FUNCTION menu.
Press UP or DOWN key to select IR SW detection INT.
IR SW can detect INT. (AGC and SENSE UP) signal.
Press ENTER key to enter IR INT LEVEL ADJUSTMENT menu.
Press UP or DOWN key to select IR INT LEVEL MIN, +1, +2, +3, +4, +5, +6, +7, +8, +9,
+11, +12, +13, +14, +15, +16, MAX, 18 steps adjustable.
IR INT LEVEL MENU
- 11 -
Page 13
______________________________________________________________________
*3
*2
OFF x 2 x 4 x 6 x 8 x 12 x 16 x 32 x 64
*1
BASE x x MAX 16 15 14 13 11 9
+1 x MAX 15 14 13 12 11 9 7
+2 x 16 14 13 12 11 10 8 6
+3 x 15 13 12 11 10 9 7 5
+4 MAX 14 12 11 10 9 8 6 4
+5 16 13 11 10 9 8 7 5 3
+6 15 12 10 9 8 7 6 4 2
+7 14 11 9 8 7 6 5 3 1
MAX 13 10 8 7 6 5 4 2 MIN
NOTE1:
*1
*2:IR INT LEVEL (ACT UP THE LEVEL)
*3:SENSE UP
NOTE2: IR INT LEVEL (MAX) Approach 15Lux (illumination)
IR INT LEVEL (MIN) Approach 0.02Lux (illumination)
: AGC LEVEL
IR SW
IR SW →EXT.
IR EXT LEVEL
IR INT LEVEL →MAX
4.18 INITIAL
FOCUS RESET FUNCTION
SETUP MENU [3/5]
POSITION LOAD.
H-GAIN +6
V-GAIN +6
MOTION ON.
IR ON.
INITIAL →ON
IR INT LEVEL TABLE
Press ENTER key to enter IR SW FUNCTION menu.
Press UP or DOWN key to select IR SW detection EXT.
IR SW will be set manual mode.
IR SW EXT. MENU
Press UP or DOWN key to select IR EXT LEVEL MAX or MIN.
IR EXT LEVEL MAX : IR CUT OFF (B/W MODE)
IR EXT LEVEL MIN : IR CUT ON (COLOR MODE)
IR EXT LEVEL MENU
Move cursor to INITIAL, press ENTER key to enter INITIAL ON/OFF menu.
Press UP or DOWN key to select ON/OFF.
Page 3 MAIN MENU
- 12 -
Page 14
______________________________________________________________________
4.19 DEFAULT
RESTART THE CAMERA AND RESET PARAMETERS TO FACTORY’S DEFAULT.
SETUP MENU [4/5]
DEFAULT →CANCEL
FREEZE OFF
FREEZE MODE FIELD
ZOOM SPEED +3
FOCUS SPEED MIN
GAMMA GAMMA1
Move cursor to DEFAULT, press ENTER key to enter DEFAULT CANCEL/OK menu.
Press UP or DOWN key to select OK, and then press ENTER key.
Page 4 MAIN MENU
4.20 FREEZE
FREEZE PICTURE FUNCTION
SETUP MENU [4/5]
DEFAULT CANCEL
FREEZE →OFF
FREEZE MODE FIELD
ZOOM SPEED +3
FOCUS SPEED MIN
GAMMA GAMMA1
Move cursor to FREEZE, press ENTER key to enter FREEZE ON/OFF menu.
Press UP or DOWN key to select ON/OFF.
Page 4 MAIN MENU
4.21 FREEZE MODE
FREEZE FIELD (or FRAME) OF PICTURE FUNCTION
Move cursor to FREEZE MODE, press ENTER key to select FREEZE MODE menu.
SETUP MENU [4/5]
DEFAULT CANCEL
FREEZE OFF
FREEZE MODE →FIELD
ZOOM SPEED +3
FOCUS SPEED MIN
GAMMA GAMMA1
Press UP or DOWN key to select FIELD/FRAME.
Page 4 MAIN MENU
4.22 ZOOM SPEED
ZOOM SPEED ADJUSTMENT
SETUP MENU [4/5]
DEFAULT CANCEL
FREEZE OFF
FREEZE MODE FIELD
ZOOM SPEED →+3
FOCUS SPEED MIN
GAMMA GAMMA1
Move cursor to ZOOM SPEED, press ENTER key to enter ZOOM SPEED
SELECTING menu, then Press UP or DOWN key to select MAX, +3, +2, +1, MIN (5
steps adjustable).
Page 4 MAIN MENU
- 13 -
Page 15
______________________________________________________________________
4.23 FOCUS SPEED
FOCUS SPEED ADJUSTMENT
SETUP MENU [4/5]
DEFAULT CANCEL
FREEZE OFF
FREEZE MODE FIELD
ZOOM SPEED +3
FOCUS SPEED →MIN
GAMMA GAMMA1
Move cursor to set FOCUS SPEED, press ENTER key to FOCUS SPEED
SELECTING menu, then Press UP or DOWN key to select MIN, +1, +2, +3, MAX (5
steps adjustable).
Page 4 MAIN MENU
4.24 GAMMA
GAMMA SELECTION
SETUP MENU [4/5]
DEFAULT CANCEL
FREEZE OFF
FREEZE MODE FIELD
ZOOM SPEED +3
FOCUS SPEED MIN
GAMMA →GAMMA1
Move cursor to set GAMMA menu, press ENTER key to select GAMMA mode , then
Press UP or DOWN key to select GAMMA1 or GAMMA2.
GAMMA1 = 0.45
GAMMA2 = 1.0
Page 4 MAIN MENU
4.25 ZOOM + AF
ZOOM TRIGGER AUTO FOCUS
SETUP MENU [5/5]
→ZOOM+AF OFF
AF SLEEP OFF
SCALE OFF
LANGUAGE ENGLISH
WINKER OFF
MISC
Move cursor to set ZOOM+AF mode, press ENTER key into select ZOOM+AF menu.
Press UP or DOWN key to select ON/OFF.
Page 5 MAIN MENU
4.26 AF SLEEP
AUTO FOCUS SLEEP (WORK IN AUTO FOCUS ON MODE)
SETUP MENU [5/5]
ZOOM+AF OFF
→AF SLEEP OFF
SCALE OFF
LANGUAGE ENGLISH
WINKER OFF
MISC
Move cursor to AF SLEEP, press ENTER key to enter AF SLEEP ON/OFF menu.
Press UP or DOWN key to select ON/OFF.
The image change less than auto focus range in five minutes; the auto focus will
sleep in AF SLEEP ON mode. Then the image change more ±6dB than auto focus
range, the auto focus will wake up.
Page 5 MAIN MENU
- 14 -
Page 16
______________________________________________________________________
4.27 SCALE
ZOOM SCALE DISPLAY
SETUP MENU [5/5]
ZOOM+AF OFF
AF SLEEP OFF
→SCALE OFF
LANGUAGE ENGLISH
WINKER OFF
MISC
Move cursor to SCALE, press ENTER key to enter SCALE ON/OFF menu.
Press UP or DOWN key to select ON/OFF.
The zoom scale will be display on right-down of the screen in SCALE ON mode.
Note: The zoom scale is non-linear approximate value. It’s a reference
value for user.
Page 5 MAIN MENU
4.28 LANGUAGE
OSD LANGUAGE SELECTION
SETUP MENU [5/5]
ZOOM+AF OFF
AF SLEEP OFF
SCALE OFF
→LANGUAGE ENGLISH
WINKER OFF
MISC
Move cursor to LANGUAGE, press ENTER key to enter LANGUAGE selecting
menu.
Press UP or DOWN key to select ENGLISH, DEUTSCH or ITALIANO language.
Page 5 MAIN MENU
4.29 WINKER
WINKER
SETUP MENU [5/5]
ZOOM+AF OFF
AF SLEEP OFF
SCALE OFF
LANGUAGE ENGLISH
→WINKER OFF
MISC
Move cursor to WINKER, press ENTER key to enter WINKER selecting menu.
Press UP or DOWN key to select WINKER ON or OFF.
Page 5 MAIN MENU
4.30 MISC
SETUP MENU [5/5]
ZOOM+AF OFF
AF SLEEP OFF
SCALE OFF
LANGUAGE ENGLISH
WINKER OFF
→MISC
Move cursor to MISC, press ENTER key to enter MISC menu.
Page 5 MAIN MENU
- 15 -
Page 17
______________________________________________________________________
4.30.1 H-REVERS
Horizontal Reverse (Mirror) Function
MISC
H-REVERS →OFF
V-REVERS OFF
POSI/NEGA POSI
PRIORITY AGC
MASK A OFF
MASK B OFF
4.30.2 V-REVERS
Vertical Reverse (Up-side Down) Function
MISC
H-REVERS OFF
V-REVERS →OFF
POSI/NEGA POSI
PRIORITY AGC
MASK A OFF
MASK B OFF
4.30.3 POSI/NEGA
Positive or Negative Picture Function
MISC
H-REVERS OFF
V-REVERS OFF
POSI/NEGA →POSI
PRIORITY AGC
MASK A OFF
MASK B OFF
4.30.4 PRIORITY
Selecting IR SW INT Detecting Signal
MISC
H-REVERS OFF
V-REVERS OFF
POSI/NEGA POSI
PRIORITY →AGC
MASK A OFF
MASK B OFF
Move cursor to H-REVERS, press ENTER key to enter FREEZE ON/OFF menu.
Press UP or DOWN key to select ON/OFF.
MISC MENU
Move cursor to V-REVERS, press ENTER key to enter FREEZE ON/OFF menu.
Press UP or DOWN key to select ON/OFF.
MISC MENU
Move cursor to POSI/NEGA, press ENTER key to enter POSI/NEGA menu.
Press UP or DOWN key to select POSI/NEGA.
Move cursor to PRIORITY, press ENTER key to enter PRIORITY menu.
Press UP or DOWN key to select AGC/SENSE UP.
MISC MENU
MISC MENU
- 16 -
Page 18
______________________________________________________________________
4.30.5 MASK A / B
MASKING AREA SETTING
MISC
H-REVERS OFF
V-REVERS OFF
POSI/NEGA POSI
PRIORITY AGC
MASK A →ON.
MASK B OFF
MASK A / B
H-POSITION →032
V-POSITION 064
H-SIZE 048
V-SIZE 032
CONNECTED OFF
Move cursor to MASK A/B, press ENTER key to enter MASK A/B menu.
Press UP or DOWN key to select ON/OFF.
Then press ENTER key to enter MASK A/B SETTING menu.
MISC MENU
Move cursor to H-POSITION, V-POSITION, H-SIZE or V-SIZE press ENTER key to
enter NUMBER SETTING menu.
Press UP or DOWN key to adjust number (Adjusting H-POSITION, V-POSITION,
H-SIZE or V-SIZE).
CONNECTED set OFF, MASK will be fixed.
CONNECTED set ON, MASK will be connected with zoom.
MASK A / B SETING MENU
4.31 Camera Address ID Setting
Push [ENTER] + [ESC] key 3 sec. to get into the OSD COMM menu.
COMM
→COMM ID 001
COMM MODE 1:1
Move cursor to COMM ID, press ENTER key to enter COMM ID SELECTING menu,
then Press UP or DOWN key to select COMM ID 001~239.
(COMM MODE must set at 1:1)
COMM SETING MENU
5. Control Methods
5.1 PC Control
For window 95/98/2000
1. Execute KB350SP_V.exe.
2. A virtue keypad icon will display on screen.
3. Use mouse to point the icons for on-screen-display setting.
4. Another methode,user can use RS-485 protocol to command zoom camera.
** To control camera via PC, RS-485 converter will be required to convert RS-232C protocol
to RS-485 protocol.
5.2 Controller
The keyboard controller can control most of the camera functions. (reference circuit).
Screwless type Terminal (REMOTE) Pin Assignment
- 17 -
Page 19
______________________________________________________________________
A
A
I
FZ
+12V
GND
03 1211100908070605040201
R3
1K
1
0
2
LARM
1
FAR
2
NEAR
1
2
1
FOCUS
2
RS485
IRIS
MOTION-H OUTPUT
2
WIDE
1
ZOOM
Correct Reference Circuit
DO
2
1
DI
OPEN
SW8
CLOSE
SW9
TELE
1 2
R2
1K
1 2
01 Iris + 07 RS485 +
02 Iris - 08 RS485 03 Focus + 09 Motion out
04 Focus - 10 GND
05 Zoom + 11 Alarm in
06 Zoom - 12 GND
IRIS+
IRIS-
+12V
MDET-H
ZOOM+
ZOOMFOCUS+
FOCUS-
+12V
+12V
LARM
R1
1K
+12V
- 18 -
Page 20
______________________________________________________________________
6. RS-485 Control
** For using RS-485 serial control, camera address ID must be set before connecting to the chain
system, please refer to 4.31 Camera Address ID Setting (p.23).
1 0
5
4
3
2
1
1 0
5
4
3
2
1
1 0
5
4
3
2
1
PELCO-P 4800
1 0
5
4
3
2
1
KAMPRO 9600
Camera Function
1 0
5
4
3
2
1
PELCO-P 2400
1 0
5
4
3
2
1
KAMPRO 19200
1 0
5
4
3
2
1
PELCO-D 9600
1 0
5
4
3
2
1
KAMPRO 38400
1 0
5
4
3
2
1
PELCO-D 4800
1 0
5
4
3
2
1
KALATEL 9600
6.1 Protocol Select
PELCO-P 9600
PELCO-D 2400
6.2 Keyboard Functions
Camera is able to receive standard commands from universal keyboard.
To call /cancel preset functions of the camera, combination key of the keyboard will be designated for every individual
function. I.e. to call the OSD manual through remote keyboard controller, using the universal keyboard, to press “70” and
then “PRESET”
Relevant Function Key
ZOOM IN Zoom Wide (Z-)
ZOOM OUT Zoom Tele (Z+)
FOCUS+ Focus Near (F+)
FOCUS- Focus Far (F-)
CLOSE Iris Close (AIS / AES)
OPEN Iris Open (AIS / AES)
[1~64]+Preset Go To Preset Point
[70]+Preset Camera OSD Key ON. *
[71]+Preset Camera ID ON
[72]+Preset Position OSD ON
[73]+Preset Zoom Scale ON
[74]+Preset Sense UP ON (+4)
[75]+Preset AIS (Auto IRIS ON)
[76]+Preset BLC ON
[77]+Preset AGC Super (MAX)
[78]+Preset Day/Night (IR) Auto ON
[79]+Preset Manual Night Mode (B/W)
- 19 -
Page 21
______________________________________________________________________
[80]+Preset ATW
[81]+Preset Digital Zoom ON
[82]+Preset Auto Focus ON
[83]+Preset Zoom +AF ON
[84]+Preset Lens Initial ON
[85]+Preset Motion ON
[86]+Preset Freeze ON
[87]+Preset Mirror ON
[88]+Preset Up/Down ON
[89]+Preset Mask 1 ON
[90]+Preset Mask 2 ON
[99]+Preset Camera Address ID Display ON
* For OSD display, the commands are as follow ==> "70" + "PRESET" and to follow with "ENT" for the display of OSD
manual, when cancel display of OSD manual, combination key "70" + "SET" for disabling of OSD manual. Also when OSD
manual is activated, that joystick command of ZOOM OUT, ZOOM IN, FOCUS +, FOCUS - representing UP, DWN, ESC, ENT
respectively to the camera.
[1~64]+Set Set (Save) Preset Point
[70]+Set Camera OSD Key OFF
[71]+Set Camera ID OFF
[72]+Set Position OSD OFF
[73]+Set Zoom Scale OFF
[74]+Set Sense Up OFF
[75]+Set AES (Auto Iris OFF)
[76]+Set BLC OFF
[77]+Set AGC Normal (+4)
[78]+Set Day/Night (IR) Auto OFF
[79]+Set Manual Day Mode (Color)
[80]+Set AWB (Hold)
[81]+Set Digital Zoom OFF
[82]+Set Auto Focus OFF
[83]+Set Zoom +AF OFF
[84]+Set Lens Initial OFF
[85]+Set Motion OFF
[86]+Set Freeze OFF
- 20 -
Page 22
______________________________________________________________________
[87]+Set Mirror OFF
[88]+Set Up/Down OFF
[89]+Set Mask 1 OFF
[90]+Set Mask 2 OFF
[99]+Set Camera Address ID Display OFF
** For keyboard not containing “CLEAR” key, following commands cannot be executed.
[1~64]+Clear Clear Preset Point
[69]+Clear One Push Auto focus
[90]+Clear Zoom Speed MIN
[91]+Clear Zoom Speed +1
[92]+Clear Zoom Speed +2
[93]+Clear Zoom Speed +3
[94]+Clear Zoom Speed MAX
[95]+Clear Focus Speed MIN
[96]+Clear Focus Speed +1
[97]+Clear Focus Speed +2
[98]+Clear Focus Speed +3
[99]+Clear Focus Speed MAX
7. Color / Monochrome Auto Change
The camera provides auto change function between color picture and monochrome (IR
filter removable function), The vivid color picture output on daytime, while under minimal
lighting around IR INT. level, the picture turned into monochrome automatically, in order
to reduce the color noise and obtain a easy identify playback picture quality after VCR
recording.
8. Low Light Performance and Infrared
Under minimal lighting environment, this camera has much better sensitivity and picture
performance than any others conventional camera does. Especially good for
applications that not allow for IR illumination. A normal color camera cannot obtain a
clear picture un der IR illumination. This camera has been specially designed with the
capability to accept both IR LED and IR lamp projection to have a clear black and white
picture under even completely dark area.
The range of Infrared wavelength is from 800 Nm to 1050 Nm.
The focus may slightly vary with IR wavelength due to lens diffraction to long-wave,
while installing the camera with IR projector, please check the focus under IR
illumination and normal light condition, and find an adequate focusing position.
It is recommended to close lens aperture one or two stops to increase the depth of filed
in order to compensate the lens diffraction.
- 21 -
Page 23
______________________________________________________________________
9. Specifications
MODEL NO. SZX23-1480 SZX23-1480P
Signal System NTSC PAL
Image Sensor 1/4-inch SUPER HAD CCD Image sensor
Picture Elements 795(H) x 596(V) / 811(H) x 508(v)
Scanning System 625lines, 2:1 Interlace / 525lines, 2:1 Interlace
Sync System Internal / External
Minimum Illumination
IR-Cut Filter Auto switching / Manu
Day-Night Change Level ADJ. 0.02 ~ 15 Lux Adjustable
Day-Night Change Delay Time 5 ~ 8 sec.
Diagonal Angle 58°(W) ~ 2.8°(T)
Zoom Speed 4.2 s
Resolution 480 TVL
S / N Ratio Over 50dB
White Balance ATW 2800ºK ~ 7500 ºK Preset / Manual
White Balance Range 2800 ~ 7500 ºK
B.L.C. Function Auto on/off
Gamma Correction 0.45 or 1
AGC Super AGC 0~36dB
ALC Auto / Fix
Electronic Shutter
Sense Up OFF, 2x ~ 64x (option)
Lens
Motor- Zoom / Focus / Iris 800,000 times life
Zoom 230x (23x optical & 10x electronic zoom)
Focus Auto / Manual
Position
Video Output Composite output 1.0Vp-p at 75 ohm
External Control RS-485 Control or controller
Function Option & Digital zoom, Focus, Iris, Gain, White balance
Protocol Type PELCO-P, PELCO-D, KAMPRO, KALATEL
Communication Baud Rate 2400, 4800, 9600, 19200, 38400 BPS
Operation Temperature -10 ºC TO 50 ºC
Storage Temperature -20 ºC TO 70 ºC
Operation Humidity 10%~ 85% RH
Power Supply
Dimensions 70 mm (H) × 63.6 mm (W) × 123.5 mm (D)
Weight 390g
The specifications and appearance of the product may change without notice.
www.okiusa.com
0.5Lux Color, IR-cut on/0.1Lux B/W, IR-cut off (Super had)
0Lux under IR illumination
1/50 ~ 1/100,000 sec. Flicker less / 1/60 ~ 1/100,000 sec.
Flicker less
Canon 23x Optical Zoom Lens
(F1.6~3.8,f =3.6~82.8 mm)
64 Position (Zoom，Focus)
DC12V ±1V / 2.8W(Max)
- 22 -
Loading...