Page 1
Hole Punch Kit (P/N 42872902)
Technician’s Installation Guide
1. Unpack the Hole Punch Kit and check the
contents:
2. Remove the packing tape, blue spacers and
any other packing materials from the Hole
Punch Unit.
3. Turn off the printer.
4. On the back of the finisher/ inverter unit,
1
unplug the inverter power cord (
2
connecting cord (
) to the finisher.
) and the
[1] Hole Punch Unit
2
]Safety Labels
[
[
3
] Screw (for securing hole punch unit to finisher:
see step 14)
[
4
]Orange Cable (4 leads)
[
5
] Purple Cable (5 leads)
Page 2
5. Push in on the finisher release lever and slide
the finisher away from the inverter.
6. Open the finisher front cover.
8. Remove the internal cover:
a. Remove the two screws behind the cover.
b. Remove the two screws holding the side of
the cover in place.
7. Squeeze the white locking tabs on the blue
knob and pull it out of the finisher.
c. Pull off the internal cover.
2
Page 3
9. Remove the screws securing the rear cover
(two on the left side [
side [
b
]), then remove the rear cover.
a
] and one on the right
a
a
10. Remove the two screws at either end of the
hole punch blank.
b
11. Swing up the finisher top cover (
2
out the punch blank unit (
).
1
) and lift
3
Page 4
12. Remove the top of the blank unit: you need
this to install the hole punch unit. Store the
bottom of the blank in case you ever remove
the hole punch from the finisher.
13. Align the pins at either end of the hole punch
unit with the holes in the finisher housing,
then slide the hole punch unit into place.
15. Open the finisher top cover and snap the top
of the blank into place on the hole punch
unit.
16. Close the top cover and secure the hole
punch unit in place with two screws at either
end.
14. Secure the hole punch unit in place: use two
1
of the screws (
the screw (
) you removed earlier, plus
2
) supplied with the hole punch
accessory.
4
Page 5
17. Insert the orange cable (4 leads) into the
connector on the hole punch unit board.
18. Insert the purple cable (5 leads) into the
connector on the hole punch unit board.
20. Plug the orange cable into the connector on
the main board.
21. Plug the purple cable into the connector on
the main board.
19. Snap open the four cable harnesses, then
thread the two cables through the harnesses
and snap each one shut.
5
Page 6
22. Reinstall the back cover and secure it in
place: two screws on the left side
one screw on the right side (
(a
) and
b
).
a
a
23. Reinstall the internal front cover and secure
it with four screws.
b
6
Page 7
24. Push the blue knob back into place.
26. Apply the appropriate language safety label:
27. Slide the finisher back into the inverter. Make
sure it locks in place.
25. Close the finisher front cover.
28. Reattach the cable between the finisher and
inverter and the finisher power cable.
29. Turn on the printer.
7
Page 8
30. Test the operation of the hole punch unit:
a. With a suitable document open in a
software application, select
[File]
→
[Print].
b. Select the appropriate Oki printer, then
click [Properties].
c. Click the [Job Options] tab.
d. Under [Finisher], [Output Bin], select
[Finisher(Face-up)] or
[Finisher(Face-down)] from the drop-down
list.
e. Under [Finisher], [Staple], select
[Punch(Long-Edge)] or
[Punch(Short-Edge)], then click [OK].
f. Print the document.
31. Demonstrate how to empty the punch
collection box:
a. Push in on the finisher release lever and
slide the finisher away from the inverter.
b. Remove the punch collection box from the
finisher.
c. Empty it, then put it back into the finisher.
d. Slide the finisher back into the inverter.
Make sure it locks in place.
© 2005 Oki Data Americas, Inc. 58372901
Loading...