PROFESSIONAL GRADE
TRACTOR
T
L4500
Easily change belts, blades
and service front tires
Tractor Lift can be used out of the box on most Zero-Turn
brands available through major retailers.
Maintenance
Store in a clean dry place.
Recommended tire pressure - 30 PSI.
Before each use:
Always check tire pressure.
Always inspect unit for damage.
Always check fasteners for tightness.
Tools required for assembly:
1. 9/16” wrench and/or socket
2. Adjustable wrench
3. Pliers
LIFT
If there are any missing parts, or if you have any
*Patent Pending
WARNINGS
• Always use the stabilizer bar provided when using tractor lift.
• Make sure stabilizer bar is properly in place before starting any work on
tractor.
• Read and understand all safety and operating instructions before using
the tractor lift. Never allow anyone unfamiliar with these instructions to
use the tractor lift.
• Read and understand all safety and operating instructions provided by
the tractor's manufacturer before using tractor lift.
• Never lay under the tractor or mowing deck.
• When using lift, keep all bystanders, including children, away.
• This tractor lift must be only used for lifting and lowering to and from a
level and stable surface.
• Never use in wet conditions.
• Do not attempt to lift the front and back of the tractor at the same time.
• Do not use tractor lift as an automotive lift, or for any other use for which
it is not intended or designed.
• If tractor lift is bowing while lifting or lowering your tractor, which
indicates an overload condition, remove the tractor immediately.
• Do not attempt to lift or lower any power equipment while motor is
running.
• Never engage blades while using tractor lift.
• Always disconnect spark plug wire from tractor before beginning any
work on tractor.
• Do not exceed the rated capacity of the tractor lift - 275 lbs.
• Failure to follow these warnings may result in property damage and/or
serious bodily injury.
questions on assembly, operation, maintenance or
safety, please call 800-652-2321
SAFETY INSTRUCTIONS
• Be sure to read and follow all safety instructions and warnings. Failure to
follow these instructions may result in damage to the product and/or
serious personal injury.
• Danger of serious personal injury exists. Serious personal injury can
occur when using a lifting device.
• Never attempt to ride any vehicle up or down the tractor lift.
• Do not climb onto tractor while tractor is in the elevated position.
• When working on the front of the tractor always place wheel chocks in
back of the rear wheels/tires.
• Always raise and lower tractor lift in a controlled fashion; do not allow
the tractor to drop too quickly, damage could occur.
• Make sure lifting arms are aligned and set to the proper distance apart
so that the equipment being loaded is well balanced on the lift.
• Do not remove warning decals from product.
• Before each use, always check for any worn, loose, or damaged parts on
the tractor lift. If any damage is present, DO NOT USE THE TRACTOR LIFT.
• Periodically check the fasteners to make sure they are still tight and in
place.
• Keep lift surface clean by occasionally cleaning with water and any mild
detergent.
• Do not add to or try to modify the tractor lift in any way. Any modifications will void any warranties.
• Failure to abide by the warnings and read the safety instructions may
result in loss of load, damage to lift and/or property, serious personal
and/or fatal injury.
Made in China
6000161-REV B 4/09
11
3
8
2
1
5
4
TOOLS REQUIRED FOR ASSEMBLY
9/16" Wrench and/or Socket
Adjustable wrench
Pliers
10A
MAINTENANCE
Store unit in a clean dry place.
Recommended tire pressure - 30 PSI.
Before each use:
Always check tire pressure.
Always inspect unit for damage.
Always check fasteners for tightness.
Page 2
HARDWARE CONTENTS
22
40
HARDWARE CONTENTS
23
25
39
24
30
Page 3
Assemble Tractor Lift
Attach Lift Tubes to Angle Frame
Attach receiver tubes ( 4 ) to angle frame ( 1 ) using bolts ( 22 ), flat washers ( 24 ), split lock
•
washers ( 23 ) and hex nuts ( 25 ).
Slide lift tubes (5) into receiver tubes (4) secure with ring grip pins (30).
•
Note:
Over-tightening receiver bolts ( 22 ) could cause damage to lift tubes ( 4 ).
adjustable width
1
22
30
24
23
4
NOTE:
5
Tractor lift has adjustable widths
25
Page 4
Assemble Tractor Lift
Attach Handle to Angle Frame
Step 1. Attach handle bottom ( 3 ) to angle frame ( 1 ) using hex bolt ( 22 ),
flat washer ( 24 ), split lock washer ( 23 ) and hex nut (25 ).
Step 2. Insert ring grip pin ( 30 ), plugs ( 38) and grips (37) as shown.
Step 3. Insert handle top ( 2 ) into handle bottom ( 3 ). Secure with hex
bolts ( 40 ), and split lock washers ( 23 ).
Step 4. Slide stabilizer bar (8) onto Foot Bar Tube. Insert hex bolt (22)
and flat washer (24) through side of handle top (2). Tighten
using split lock washer (23) and hex nut (25).
Step 5. Align hole in stabilizer bar (8) with hex bolt (22).
Tighten using wing nut (39).
Foot Bar Tube
22
38
24
40
23
22
30
24
23
3
25
1
8
39
2523
37
2
Page 5
Using the Tractor Lift
Center Tractor Lift in front of tractor.
•
Align lift tube claws with mowing deck and roll Tractor Lift
•
forward to engage.
Check that claws are securely hooked under the mowing deck.
•
Place foot onto foot bar and apply continuous forward pressure
•
with foot while pulling down on tractor lift handle.
Once lifted, the weight of the tractor will automatically force the
•
handle down into the correct position.
Page 6.
IMPORTANT: Stabilizer bar MUST be engaged
•
immediately after raising the tractor. See Step 3
on page 7 for instructions.
OPERATION
Using the Tractor Lift
Step 3. Engaging Stabilizer Bar
Stabilizer bar MUST be engaged immediately after raising the tractor.
WARNING
injury and or property damage.
•
•
•
•
: Failure to engage stabilizer bar may result in serious personal
Remove securing wingnut ( 39 ) from tube handle. Slide stabilizer bar
( 8 ) from foot bar tube.
Turn stabilizer bar 180 degrees as shown at bottom of Figure 1.
Position stabilizer bar under base of unit between wheels.
Slide stabilizer bar back onto foot bar tube as shown in Figure 2.
Tube Handle
Figure 1
39
Turn 180
Slide stabilizer bar
back onto foot bar.
8
Figure 2
Page 7.
Service Parts List
2
37
39
24
22
25
11
23
8
23
3
40
10A
38
1
25
30
22
20
9
30
20
23
30
24
24
22
21
23
25
5
4
Page 8
Loading...