Oceanic IR3030 Corner, IR3030 Parallel, IR3030 L Shape, IR4030 Assembly Manual

Sauna & Steam

Oceanic Ltd, Pountney Street, Wolverhampton, WV2 4HX

Phone: [phone] [e-mail] www.oceanic-saunas.co.uk

Infrared Sauna

Assembly Manual

Sauna & Steam

Oceanic Saunas 01902 450 550 [e-mail]

2

Infrared Sauna Assembly

Table of contents

1. Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

2. General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

3. Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

4. Base . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

5. Fix Corner Panels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

6. Add Door -

Important: Wear goggles and gloves at all times whilst handling the door. . . . . . . . . .5

7. Add Roof . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

8. Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

9. Audio Input (AUX) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

10. Bench Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

11. Fix the bench end rails. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

12. Fix the bench . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

13. Back Rest Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

14. Fix the back rest . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

15. Internal Trim . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

16. External Trim . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

17. Floor Matt Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

18. Connection to Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

19. Keypad functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

20. Keypad Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Sauna & Steam

Oceanic Saunas 01902 450 550 [e-mail]

3

Infrared Sauna Assembly

1. Safety Precautions

Please read these precautions before entering the sauna. If you have any questions or concerns
ask a member of sta before using the sauna.

• Do not wire this sauna on a multi plug or multi socket extension lead.

• Read operating instructions before turning on the sauna.

• Do not cover the heaters as this could cause a re.

• Do not touch the heaters, they are very hot while the sauna is on.

• Do not use back rests as arm rests as you could touch the heater with the side of your arm.

• Elderly persons, pregnant women, or these suering heart disease, high blood pressure, diabetes or
not in good health are advised to seek medical opinion before using a sauna room.

• Do not smoke in the sauna room;

• Avoid using the sauna room immediately after strenuous exercise;

• Do not use the sauna room when under the inuence of alcohol;

• Leave the sauna room at once if you feel sleepy, sick or uncomfortable;

• Ensure there is good ventilation for the sauna room

• We do not recommend this product is used by children under 16years old unless they are supervised
by an adult

• This appliance is not intended for use by persons including children with reduced physical, sensory
or mental capabilities or lack of experience unless they have been given supervisor or instruction
concerning the use by a person responsible for their safety

• Commercial operators should post a notice of these precautions in a prominent position.

Sauna & Steam

Oceanic Saunas 01902 450 550 [e-mail]

4

Infrared Sauna Assembly

4. Base

i. Lay out the 32 x 32mm base section as shown below with the correct 9mm spacings.
ii. Check the base drawing on the parts list supplied
iii. Check the base with a spirit level, you may need to use packers to get a level base.
iv. Use a set square or measure corner to corner with a tape measure to ensure the base is square.
v. To make the following stages easier we recommend that you x the base to the oor, this is

completely optional and is not required for the structural integrity of the cabin.

2. General

Important Notice: Unless you ordered a “low height wiring kit” it is not possible to install our Infra­Red Sauna Cabins with a height lower than 2200mm as the wiring is all done above the sauna.

Before you begin the assembly work we recommended that you read through these instructions
completely in order to familiarise yourself with the procedure.
Each model of sauna has it’s own dedicated parts list, make sure you locate this before continuing.

This sauna cabin is for indoor use only.

Infrared Saunas can be erected onto a level oor that can be vinyl, ceramic, concrete, or wood, but
preferably not carpet.

3. Requirements

You will require the following items:­i. The easiest and fastest way to trim this cabin is to use a brad nailer, electric, gas or air all are ok.

The brads we supply are straight 18 gauge 25mm and 40mm length. If you don’t have a nailer

you can pilot & screw or break the individual brads o the strips and use a hammer.
ii. A powered drill/screw driver with drill bits, PH2 and PZ2 driver bits
iii. 4mm drill and countersink tool
iv. Spirit level
v. Hammer
vi. Hand Saw or an electric mitre or cross cut saw is advised for cutting trim to give a professional

nish.
vii. Sand Paper
viii. Window packers or alternatively make some using cross cut saw from spare timber.
ix. Optional: - if it is possible to x the unit to the oor you will need a hammer drill and raw plugs

Sauna & Steam

Oceanic Saunas 01902 450 550 [e-mail]

5

Infrared Sauna Assembly

5. Fix Corner Panels

i. Find the oor plan in the parts list for the cabin you are building, this will indicate where each

panel needs to go.
i. Start by xing the corners together, pre drill 4 holes using a 4mm counter sink & drill.
ii. Fix using the 80mm screws provided

6. Add Door - Important: Wear goggles and gloves at all times whilst handling the door.

i. The door is the same size as the full sizes panels so it can be moved around in most cabins. We will show

the dierent ways to join the door with the panels in the following points.

ii. If you are working alone we advise that you remove the glass from the hinges and set to one side.

iii. To install the door as shown in the 2D image below (on the corner against the end of the side panel).

Firstly with 30mm screws evenly x the 4 at brackets down to the inside edge (30mm side) of the
door frame (hinge or handle side just rotate the frame 180

o

). Then x to the end of the side panel using

30mm screws. (see page 19 for trimming edge of panel and magnetic catch info)

Sauna & Steam

Oceanic Saunas 01902 450 550 [e-mail]

6

Infrared Sauna Assembly

iv. To x the door in between two panels or to the inside face of a side panel (as the 2D drawings below).

vi. If you want you can x the other front panel to the door now or later when xing the roof.

v. Pilot and counter sink 4 holes and use

50mm screws to x into the panel adjacent.

Sauna & Steam

Oceanic Saunas 01902 450 550 [e-mail]

7

Infrared Sauna Assembly

7. Add Roof

i. If you are installing the cabin with a restricted height (less than 2200mm) and have purchased

the “Low Height Kit” you will be supplied with an additional guide for xing the roof.
ii. If you have a height of 2200mm or above please use the following steps.
iii. Start with the back roof panel, start from the corners to square up the wall panels, pilot and

counter sink holes and use 60mm screws, don’t screw near the cable holes.
iv. Fix the roof panels to each other in the centres check they are ush on the inside face.
v. When you x above the door use 50mm screws so they don’t stick through top of the frame or

countersink and screw from underneath.

vi. If you levelled and squared the base properly

the door should open perfectly at this stage. If it
doesn’t you may need to pack the base up, use
a spirit level to make things easier.

vii. Fix the other side of the door if you haven’t

already done this at the previous stage.

Sauna & Steam

Oceanic Saunas 01902 450 550 [e-mail]

8

Infrared Sauna Assembly

8. Wiring

8.1. Keypad and Temperature Sensor

i. Do not turn any power on until the cabin

has been fully installed.

ii. Refer to the parts list for a wiring

schematic.

iii. Sit the control box on the roof in the

iv. Then pull out of the hole

on the inside.

v. To mount the heaters x

2 x 30mm the 2x 30mm
screws into the two
indicated holes. Leave
them protruding slightly so
you can hang the heaters
o them, similar to how
you would t a picture
frame or clock.

specied position.
iv. The temperature sensor and keypad will already be tted onto there panels, route these across

the roof, through the channels made in the frame to the control box connections and plug them

in.

8.2. Wall Heaters

i. For the heaters use the correct length of cable as shown on the schematic.
ii. Plug the one end into the control as shown below.
iii. Then route the other end down from the roof into the walls panels.

Sauna & Steam

Oceanic Saunas 01902 450 550 [e-mail]

9

Infrared Sauna Assembly

vi. Plug the heater wire in.

vii. Then mount the heater onto

the wall. (Don’t remove grill)

viii. Fix at the bottom with 2 x

30mm screws.

8.3. Under Bench Heaters

i. Pilot drill and screw 2 x 30mm

screws at 700mm centres approx

200- 300mm from the oor, but

most importantly 40mm to the left

o the centre of the wire hole.

ii. Hang the heater onto the screws.

Sauna & Steam

Oceanic Saunas 01902 450 550 [e-mail]

10

Infrared Sauna Assembly

8.4. Lighting

i. Assemble the spot light(s) as shown and t into the ceiling hole(s).
ii. Install either standard or colour changing bulb(s) if supplied
iii. If you ordered the deluxe specication you will be supplied with a remote control to control the

lights, you can choose between many dierent colours, there is also a fade mode.

iii. Secure at the bottom with 1 x 30mm

screw.

iv. Finally Plug the pre wired light cable into the socket on the control box labelled “Light”

Note: It is possible to switch a second lighting circuit separately using the chromo input. This would
be useful if you wanted the option of both white and coloured lighting. Oceanic provides one pre
wired cable as standard.