NXP Semiconductors UM11055 User Manual

UM11055

NXP USB PD shield board user manual

Rev. 1.0 — 9 February 2018 User manual

Document information

Information Content

Keywords OM13588, USB Type-C, PD (power delivery), Alt-mode-DP, Host, Dock

Abstract This user manual presents demonstration / application kit capability of power,

data delivery through single USB Type-C cable between a shield board used
in conjunction with a Kinetis KL27Z FRDM Board and a USB-PD capable
device or Power source.

NXP Semiconductors

UM11055

NXP USB PD shield board user manual

UM11055 All information provided in this document is subject to legal disclaimers. © NXP B.V. 2018. All rights reserved.

User manual Rev. 1.0 — 9 February 2018

2 / 12

Revision history

Revision history

Rev Date Description

v.1.0 20180209 Added note to section 3.1

v.0.3 20170619 Minor corrections to text

v.0.2 20170608 Updated document information keywords

v.0.1 20170501 Initial version

NXP Semiconductors

UM11055

NXP USB PD shield board user manual

UM11055 All information provided in this document is subject to legal disclaimers. © NXP B.V. 2018. All rights reserved.

User manual Rev. 1.0 — 9 February 2018

3 / 12

1 Introduction

The main purpose of this user’s manual is to illustrate USB-PD operation for a Type C
port using PTN5110 PD PHY and KL27 PD controller.

PTN5110 is a 1-port TCPC compliant USB Power Delivery (PD) PHY IC that implements
Type-C Configuration channel interface and USB PD Physical layer functions to a Type­C Port Manager that handles PD Policy management. It complies with USB PD, Type-C
and TCPC specifications and relevant ECNs/ECRs. This IC is targeted primarily for use
in system platforms.

PTN5110 is a USB PD TCPC PHY IC, in HX2QFN16 2.6 mm x 2.6 mm x 0.35 mm, 0.4
mm pitch package.

The demo kit is intended to demonstrate the power, USB data delivery through single
USB Type-C cable between a shield board mounted on a KL27Z FRDM Board and any
USB PD capable device or power adaptor. It also has the power swap, high/low power
request capability between the shield board and connected PD Source or Sink.

This document describes the user manual of NXP USB PD Shield board,

• Overall PCB connectors, jumpers, and power supplies.

• Setup Information for USB-PD operation

• Setup Information for USB TypeC operation using simple CC Logic

1.1 Purposes

• For customers to evaluate NXP USB Type-C Power Delivery PHY and protocol IC

PTN5110 and DP Alternate Mode features through single USB Type-C connection.

– Power swap between the shield board and any connected SRC/SNK.
– Power delivery between the Shield and any connected SRC.
– Power delivery selection between 5V or 9V.
– CC logic and PD control through Kinetis KL27Z residing on the Freedom board.
– Transfer power, data through USB Type-C cable between the shield board and any

connected device or power adaptor.

NXP Semiconductors

UM11055

NXP USB PD shield board user manual

UM11055 All information provided in this document is subject to legal disclaimers. © NXP B.V. 2018. All rights reserved.

User manual Rev. 1.0 — 9 February 2018

4 / 12

2 General description

2.1 Block diagram

2.1.1 USB-PD shield board schematic block diagram

shieldboardBD

PTN5110

ARDUIN

O

HEADERS

ARDUINO
HEADERS

9VPowerJac

k

USB3.0A

Receptacle

TypeCconnector

NX5P329

0

NX20P509

0

PTN3604

3

5

V

Regulato

r

PTN

5150A

NX20P

509

0

V

B

U

S

U

S

B

3

,U

SB

2

C

C

1

I2C, INT, CROS

S

C

C

2

A

100

6

I

2C

3.3

V

Regulato

r

1.8

V

Regulator

Figure 1. USB PD shield board block diagram