NXP Semiconductors JN5179M0 User Manual
UM10983
ZigBee PRO and IEEE802.15.4 JN5179-001-M00 module
Rev. 1.0 — 9 March 2016 User manual
Document information
Info Content
Keywords JN5179, ZigBee, module
Abstract JN5179-001-M00 module user manual
NXP Semiconductors
UM10983
ZigBee PRO and IEEE802.15.4 JN5179-001-M00 module
Revision history
Rev Date Description
1.0 20160309 Initial version
Contact information
For more information, please visit: http://www.nxp.com
For sales office addresses, please send an email to: salesaddresses@nxp.com
UM10983 All information provided in this document is subject to legal disclaimers. © NXP Semiconductors N.V. 2016. All rights reserved.
User manual Rev. 1.0 — 9 March 2016 2 of 23
NXP Semiconductors
ZigBee PRO and IEEE802.15.4 JN5179-001-M00 module
UM10983
1. General description
The JN5179-001-M00 module family provides designers with a ready-made component
that provides a fully integrated solution for applications, using the IEEE802.15.4 standard
in the 2.4 GHz - 2.5 GHz ISM frequency band, including ZigBee Sma rt Ener gy a nd Hom e
Automation and can be quickly and easily included in product designs. The module
integrates all of the RF components required, removing the n eed to perform expensive RF
design and test. Products can be designed by simply connecting sensors and switches to
the module IO pins. The module uses NXP’s single chip IEEE802.15.4 wireless
microcontroller, allowing designers to make use of the extensive chip development
support material. Hence, this module allows designers to bring wireless applications to
market in the minimum time with significantly reduce d de ve lopm en t effort and co st.
JN5179-001-M00 module has FCC and Industry Canada modular approval. it is also CE
compliant and subject to a Notified Body Opinion.
1.1 FCC and Industry Canada identification
Table 1. FCC and Industry Canada identification
Module name Description FCCID Industry Canada
JN5179-001-M00 Standard power, integrated antenna XXMJN5179M0 8764A-JN5179M0
1.2 Regulatory approvals
The JN5179-001-M00 has been tested against the requirements of the following
European standards.
• Radio EN 300 328 v 1.9.1
• EMC, EN 301 489-17 v 2.2.1, EN 62479 2010, EN 301 489-1 v 1.9.2
• Basic Safety Assessment (BSA) EN 60950-1:2006
A Notified Body statement of opinion for this standard is available on request.
Additionally, the module has received FCC “Modular Approval”, in compliance with CFR
47 FCC part 15 regulations and in accordance to FCC public notice DA00-1407. The
modular approval notice and test report are available on request.
The module is compliant to Industry Canada RSS210 (Issue8 Annex8) and has Industry
Canada modular approval.
2. Features and benefits
2.1 Benefits
• Microminiature module solutions
• Ready to use in products
• Minimises product development time
• No RF test required for systems
• Compliant with:
UM10983 All information provided in this document is subject to legal disclaimers. © NXP Semiconductors N.V. 2016. All rights reserved.
User manual Rev. 1.0 — 9 March 2016 3 of 23
NXP Semiconductors
2.2 Features: module
•
• Integral antenna
• 16 mm 30 mm PCB size
• TX power 8.5 dBm/10 dBm
• Receiver sensitivity –96 dBm
• TX current 22.5 mA at 10 dBm
• TX current 19.6 mA at 8.5 dBm
• RX current 14.8 mA at maximum input level 10 dBm
• RX current 12.7 mA at maximum input level 0 dBm
• 2.0 V to 3.6 V battery operation
• 3.6 V to 10 V operation with internal switched mode power supply
UM10983
ZigBee PRO and IEEE802.15.4 JN5179-001-M00 module
– FCC 47CFR Part 15C
– ETSI EN 300-328 V1.9.1
– EN 301-489-17 V2.2.1
– EN60950-1-2006
– Temperature range: 40 C to +85 C
– Lead-free and RoHS compliant
2.4 GHz IEEE 802.15.4, ZigBee Smart Energy and Home Automation compatible
2.3 Features: microcontroller
• ARM Cortex-M3 CPU with debug support
• JN5179: 512 kB/32 kB/4 kB (Flash/RAM/EEPROM)
• OTA firmware upgrade capability
• 32 MHz clock selectable down to 1 MHz for low-power operation
• Dual PAN ID support
• Fail-safe I
2
C-bus interface. operates as either master or slave
• 8 Timers (6 PWM and 2 timer/counters)
• 2 low-power sleep counters
• 2 UART supporting DALI and DMX512, one with flow control
• SPI-bus master and slave port, 2 simultaneous selects
• Variable instruction width for high coding efficiency
• Multi-stage instruction pipeline
• Data EEPROM with guaranteed 100 k write operations
• ZigBee PRO stack with Smart Home, Smart Lighting and Smart Energy profiles
• Supply voltage monitor with 8 programmable thresholds
• Battery voltage and temperature sensors
• 6-input 10-bit ADC
• Analog comparator
UM10983 All information provided in this document is subject to legal disclaimers. © NXP Semiconductors N.V. 2016. All rights reserved.
User manual Rev. 1.0 — 9 March 2016 4 of 23
NXP Semiconductors
• Digital monitor for ADC
• Watchdog timer and POR
• Standby power controller
• Up to 18 Digital IO (DIO) and 2 digital outputs pins
3. Applications
• Robust and secure low-power wireless applications
• Thread
• ZigBee 3.0
• Commercial Building and Home Automation
• ZigBee Smart Energy networks
• Smart Lighting and ZigBee Light Link networks
• Toys and gaming peripherals
• Energy harvesting, for example self-powered light switch
• Remote control
UM10983
ZigBee PRO and IEEE802.15.4 JN5179-001-M00 module
4. Overview
5. Marking
The JN5179-001-M00 is an ultra-low power, high performance surface mount module
targeted at IEEE 802.15.4, ZigBee Smart Energy , ZigBee LightLink and Home Automation
networking applications, enabling us er s to re aliz e pr od uc ts with minim u m tim e to mark e t
and at the lowest cost. It removes the need for expensive and lengthy development of
custom RF board designs and test suites. The module uses NXP’s JN5179 wireless
microcontroller to provide a comprehensive solution with large memory, high CPU and
radio performance and all RF components included. All that is required to develop and
manufacture wireless control or sensing products is to connect a power supply and
peripherals such as switches, actuators and sensors, considerably simplifying product
development.
The module includes an integrated antenna.
JN5179-001-M00
FCC ID:XXMJN5179M0
IC: 8764A-JN5179M0
0081
aaa-022128
Fig 1. JN5179-001-M00 package marking (top view)
UM10983 All information provided in this document is subject to legal disclaimers. © NXP Semiconductors N.V. 2016. All rights reserved.
User manual Rev. 1.0 — 9 March 2016 5 of 23
NXP Semiconductors
Table 2. Marking code
Line number Marking code
Line 1 NXP Logo: B&W outline logo
Line 2 part ID: JN5179-001-M00
Line 3 FCC ID: XXMJN5179M0
Line 4 IC ID: 8764A-JN5179M0
Line 5 European notified body number
The JN5179-001-M00 module meets the requirements of Directive 2002/95/EC of the
European Parliament and of the Council on the Restriction of Hazardous Substance
(RoHS) and of the Chinese RoHS requirements SJ/T11363-2006 which came into force
on 1st March 2007.
6. Block diagram
UM10983
ZigBee PRO and IEEE802.15.4 JN5179-001-M00 module
10 V to 3.6 V
SWITCHED MODE
POWER SUPPLY
XTAL
MANAGEMENT
Fig 2. Block diagram
2.4 GHz
RADIO
INCLUDING
DIVERSITY
POWER
WATCHDOG
TIMER
VOLTAGE
BROWNOUT
O-QPSK
MODEM
IEEE802.15.4
MAC
ACCELERATOR
128-BIT AES
ENCRYPTION
ACCELERATOR
RAM
ARM Cortex-M3
EEPROM
FLASH
SPI-BUS MASTER
AND SLAVE
2
C-BUS MASTER
I
AND SLAVE
6 x PWM
PLUS TIMER
2 x UART
DIO
SLEEP COUNTER
6 CHAN
10 BIT ADC
SUPPLY AND
TEMP SENSORS
aaa-015434
UM10983 All information provided in this document is subject to legal disclaimers. © NXP Semiconductors N.V. 2016. All rights reserved.
User manual Rev. 1.0 — 9 March 2016 6 of 23
NXP Semiconductors
7. Pinning information
7.1 Pinning
DIO2
ADC0
DIO0
DIO1
DIO3
DIO4
DIO10
DIO9
DIO8
UM10983
ZigBee PRO and IEEE802.15.4 JN5179-001-M00 module
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
(1)
SPIMISO
SPIMOSI
SPI_CS
Transparent top view
DIO17
SPICLK
DIO11
SS
V
DD(SMPS)
V
ADC1
27
26
DIO18
DIO15
25
24
RESET_N
23
DIO14
22
DIO13
DIO12
21
20
n.c.
DIO5
19
18
DD
V
aaa-022129
(1) SPI_CS = SPISEL0 on the JN5179.
Fig 3. Pin configuration
7.2 Pin description
Table 3. Pin description
Symbol Pin Type
DIO2 1 IO DIO2 (I) pull-up DIO2 — digital input/output 2
ADC0 2 I
[1]
Default at reset/
during boot
Default internal
pull-up/pull-down
Description
ADC5 — ADC input 5
2
SDA — I
C-bus master/slave SDA
input/output (push-pull output)
RXD1 — UART 1 receive data input
TIM0CAP — Timer0 capture input
RFRX — radios receiver control output
VAUX_SENSE — auxiliary voltage sense
input
[2]
ADC0 — ADC input 0
UM10983 All information provided in this document is subject to legal disclaimers. © NXP Semiconductors N.V. 2016. All rights reserved.
User manual Rev. 1.0 — 9 March 2016 7 of 23
Loading...