NXP Semiconductors JN5169M0V2, JN5169M6V2 User Manual
UM11016
ZigBee PRO and IEEE802.15.4 JN5169-001-M0x-2 modules
Rev. 1.0 — 15 June 2016 User manual
Document information
Info Content
Keywords JN5169, Zigbee, module
Abstract JN5169-001-M0x-2 modules user manual
NXP Semiconductors
UM11016
ZigBee PRO and IEEE802.15.4 JN5169-001-M0x-2 modules
Revision history
Rev Date Description
1.0 20160613 Initial version
Contact information
For more information, please visit: http://www.nxp.com
For sales office addresses, please send an email to: salesaddresses@nxp.com
UM11016 All information provided in this document is subject to legal disclaimers. © NXP Semiconductors N.V. 2016. All rights reserved.
User manual Rev. 1.0 — 15 June 2016 2 of 24
NXP Semiconductors
1. General description
The JN5169-001-M0x-2 (with x = 0, 3 or 6) module family provides designers with a
ready-made component that provides a fully integr ated solution for applications, using the
IEEE802.15.4 standard in the 2.4 GHz - 2.5 GHz ISM frequency band, including ZigBee
Smart Energy, Home Automation and ZigBee 3.0 and can be quickly and easily included
in product designs. The modules integrate all of the RF components required, removing
the need to perform expensive RF design and test. Products can be designed by simply
connecting sensors and switches to the module IO pins. The module uses NXP’s single
chip IEEE802.15.4 wireless microcontroller, allowing designers to make use of the
extensive chip development support material. Hence, these modules allow designers to
bring wireless applications to market in the minimum time with significantly reduced
development effort and cost.
3 variants are available: JN5169-001-M00-2, JN5169-001-M03-2 and
JN5169-001-M06-2.
UM11016
ZigBee PRO and IEEE802.15.4 JN5169-001-M0x-2 modules
The variants available are described in the Table 1
.
1.1 Variants and identifications information
Table 1. Variants and identifications information
Type number Description FCCID IC ID ANATEL ID
JN5169-001-M00-2 Standard power, integrated printed antenna XXMJN5169M0V2 8764A-JN5169M0 <tbd>
JN5169-001-M03-2 Standard power, FL connector XXMJN5169M3V2 8764A-JN5169M3 <tbd>
JN5169-001-M06-2 High power, FL connector XXMJN5169M6V2 8764A-JN5169M6 <tbd>
1.2 Regulatory approvals
The JN5169-001-M0x-2 has been tested against the requirements of the following
European standards.
• Radio EN 300 328 v 1.9.1
• EMC, EN 301 489-17 v 2.2.1, EN 62479 2010, EN 301 489-1 v 1.9.2
• Basic Safety Assessment (BSA) EN 60950-1:2006
A Notified Body statement of opinion for this standard is available on request.
The High-power module with M06 suffix is not ap proved for use in Europe.
All module types have received FCC “Modular Approval”, in compliance with CFR 47 FCC
part 15 regulations and in accordance to FCC public notice DA00-1407. The modular
approvals notice and test reports are available on request.
Additionally, all module types have also received ANATEL “Modular Approval”
2. Features and benefits
2.1 Benefits
• Microminiature module solutions
UM11016 All information provided in this document is subject to legal disclaimers. © NXP Semiconductors N.V. 2016. All rights reserved.
User manual Rev. 1.0 — 15 June 2016 3 of 24
NXP Semiconductors
• Ready to use in products
• Minimises product development time
• No RF test required for systems
• Compliant with:
• Temperature range: 40 C to +85 C
• Lead-free and RoHS compliant
2.2 Features: modules
• 2.4 GHz IEEE 802.15.4, ZigBee Smart Energy and Home Automation compatible
• JN5169-001-M00-2
• JN5169-001-M03-2
• JN5169-001-M06-2
UM11016
ZigBee PRO and IEEE802.15.4 JN5169-001-M0x-2 modules
– FCC 47CFR Part 15C
– ETSI EN 300-328 V1.9.1
– EN 301-489-17 V2.2.1
– EN60950-1-2006
– ANATEL
– Dimensions: 16 mm 30 mm
– Integrated printed antenna
– TX power 8.5 dBm/10 dBm
– Receiver sensitivity –96.5 dBm
– TX current 27.2 mA at 10 dBm
– TX current 23.6 mA at 8.5 dBm
– RX current 17.8 mA at maximum input level 10 dBm
– RX current 16.2 mA at maximum input level 0 dBm
– 2.0 V/3.6 V operation
– Dimensions: 16 mm 21 mm
– Fl connector
– TX power 8.5 dBm/10 dBm
– Receiver sensitivity –96.5 dBm
– TX current 27.2 mA at 10 dBm
– TX current 23.6 mA at 8.5 dBm
– RX current 17.8 mA at maximum input level 10 dBm
– RX current 16.2 mA at maximum input level 0 dBm
– 2.0 V/3.6 V operation
– Dimensions: 16 mm 30 mm
– Fl connector
– TX power 21 dBm
– Receiver sensitivity –100 dBm
UM11016 All information provided in this document is subject to legal disclaimers. © NXP Semiconductors N.V. 2016. All rights reserved.
User manual Rev. 1.0 — 15 June 2016 4 of 24
NXP Semiconductors
2.3 Features: microcontroller
•
• Variable instruction width for high coding efficiency
• Multi-stage instruction pipeline
• 512 kB Flash
• 32 kB RAM
• 4 kB EEPROM
• Data EEPROM with guaranteed 100 k write operations
• ZigBee PRO stack with Home Automation and Smart Energy profiles
• 2-wire I
• 5 PWM (4 timers, 1 timer/counter)
• 2 low-power sleep counters
• 2UARTs
• SPI-bus Master and Slave port, 3 selects
• Supply voltage monitor with 8 programmable thresholds
• 6-input 10-bit ADC, comparator
• Battery and temperature sensors
• Watchdog and Supply Voltage Monitor (SVM)
• Up to 20 Digital IO (DIO) pins
ZigBee PRO and IEEE802.15.4 JN5169-001-M0x-2 modules
– TX current 181 mA at 21 dBm
– RX current 22.8 mA
– 2.0 V/3.6 V operation
32-bit RISC CPU; 1 MHz to 32 MHz clock speed
2
C-bus compatible serial interface; can operate as either master or slave
UM11016
3. Applications
• Robust and secure low-power wireless applications
• ZigBee Smart Energy networks
• ZigBee Home Automation networks
• ZigBee 3.0 networks
• Toys and gaming peripherals
• Energy harvesting - for example, self-powered light switch
4. Overview
The JN5169-001-M0x-2 family is a range of ultra-low power, high performance surface
mount modules targeted at IEEE 802.15.4, ZigBee Smart Energy, Home Automation and
ZigBee 3.0 networking applications, enabling users to realize pro ducts with minimum time
to market and at the lowest cost. It removes the need for expensive and lengthy
development of custom RF board designs and test suites. The module uses NXP’s
JN5169 wireless microcontroller to provide a comprehensive solution with large memory,
high CPU and radio performance and all RF components included. All that is required to
UM11016 All information provided in this document is subject to legal disclaimers. © NXP Semiconductors N.V. 2016. All rights reserved.
User manual Rev. 1.0 — 15 June 2016 5 of 24
NXP Semiconductors
develop and manufacture wireless control or sensing products is to connect a power
supply and peripherals such as switches, actuators and sensors, considerably simplifying
product development.
3 module variants are available:
• JN5169-001-M00-2 with an integrated printed antenna
• JN5169-001-M03-2 with a FL antenna connector
• JN5169-001-M06-2 with a FL antenna connector and also a power amplifier and
5. Marking
5.1 JN5169-001-M00-2 and JN5169-001-M03-2
UM11016
ZigBee PRO and IEEE802.15.4 JN5169-001-M0x-2 modules
LNA for extended range
JN5169-001-M0x-2
NNNNN
ZbHYWW
FCC ID:XXMJN5169MxV2
IC: 8764A-JN5169Mx
(1)
(1)
(1)
Fig 1. JN5169-001-M00-2 and JN5169-001-M03-2 packages marking (top view)
Table 2. Marking code
Line number Marking code
Line 1 NXP Logo: B&W outline logo
Line 2 part ID: JN5169-001-M0x-2
[1]
Line 3 serial number: NNNNN
Line 4 PMC code: ZbHYWW
Z: SSMC
b: SPIL
H: Halogen free
Y: year
WW: week
Line 5 FCC ID: XXMJN5169MxV2
Line 6 IC: 8764A-JN5169Mx
[1]
[1]
[1] With x = 0 or 3.
The JN5169-001-M0x-2 (with x = 0 or 3) family modules meet the requirements of
Directive 2002/95/EC of the European Parliament and of the Council on the Restriction of
Hazardous Substance (RoHS) and of the Chinese RoHS requirements SJ/T11363-2006
which came into force on 1st March 2007.
UM11016 All information provided in this document is subject to legal disclaimers. © NXP Semiconductors N.V. 2016. All rights reserved.
User manual Rev. 1.0 — 15 June 2016 6 of 24
NXP Semiconductors
5.2 JN5169-001-M06-2
Fig 2. JN5169-001-M06-2 package marking (top view)
Table 3. Marking code
Line number Marking code
Line 1 NXP Logo: B&W outline logo
Line 2 part ID: JN5169-001-M06-2
Line 3 serial number: NNNNN
Line 4 PMC code: ZbHYWW
Line 5 FCC ID: XXMJN5169M6V2
Line 6
ZigBee PRO and IEEE802.15.4 JN5169-001-M0x-2 modules
Z: SSMC
b: SPIL
H: Halogen free
Y: year
WW: week
IC: 8764A-JN5169M6
JN5169-001-M06-2
NNNNN
ZbHYWW
FCC ID:XXMJN5169M6V2
IC: 8764A-JN5169M6
UM11016
The JN5169-001-M06-2 module meets the re quirements of Directive 2002/95/EC of the
European Parliament and of the Council on the Restriction of Hazardous Substance
(RoHS) and of the Chinese RoHS requirements SJ/T11363-2006 which came into force
on 1st March 2007.
UM11016 All information provided in this document is subject to legal disclaimers. © NXP Semiconductors N.V. 2016. All rights reserved.
User manual Rev. 1.0 — 15 June 2016 7 of 24
NXP Semiconductors
6. Block diagram
UM11016
ZigBee PRO and IEEE802.15.4 JN5169-001-M0x-2 modules
integrated
antenna
external
antenna
external
antenna
CONNECTOR
CONNECTOR
µFL
Fig 3. Block diagram
µFL
PA/LNA
MATCHING
M00-2 option
MATCHING
M03-2 option
MATCHING
M06-2 option
XTAL
2.4 GHz
RADIO
INCLUDING
DIVERSITY
POWER
MANAGEMENT
WATCHDOG
TIMER
VO LTAGE
BROWNOUT
O-QPSK
MODEM
IEEE802.15.4
MAC
ACCELERATOR
128-BIT AES
ENCRYPTION
ACCELERATOR
RAM
32 kB
RISC CPU
EEPROM
32-BIT
4kB
FLASH
512 kB
SPI-BUS
MASTER AND SLAVE
2-WIRE SERIAL
(MASTER/SLAVE)
4 X PWM
PLUS TIMER
2 X UART
20 DIO
PLUS 2 DO
SLEEP
COUNTER
6 CHAN
10 BIT ADC
BATTERY AND
TEMP SENSORS
POWER
aaa-022823
UM11016 All information provided in this document is subject to legal disclaimers. © NXP Semiconductors N.V. 2016. All rights reserved.
User manual Rev. 1.0 — 15 June 2016 8 of 24
Loading...