Page 1
HVP-KV31F120M
Quick Start Guide
Freescale Controller Card
High–Voltage
Development
Platform
Page 2
2
HVP-KV31F120M
High-Voltage Development Platform
The Freescale High-Voltage Development Platform is a set of software and
hardware tools for evaluation and development of high-voltage motor control
and power conversion algorithms. It is ideal for rapid prototyping of highvoltage microcontroller-based applications.
Quick Start Guide
Get to Know the HVP-KV31F120M
Figure 1: HVP-KV31F120M
MKV31F120M
MCU
Isolated Power
Supply
USB Mini for Communication,
Debugging and Power Supply
Open SDA
Primary
Interface
SWD Isolator
Main Board
Interface
OpenSDA
JTAG
Target Reset/
Bootloader
Enable
Page 3
3
freescale.com
Introduction to HVP-KV31F120M
High-Voltage Development Platform
The HVP-KV31F120M controller card is a development platform for the Kinetis KV3x
family which in combination with one of HVP-MC3PH High-Voltage Development
Platform provides ready-made software and hardware development for high- voltage
motor control and power conversion applications.
This Quick Start Guide will teach you to:
• Easily program precompiled examples for the KV31 MCU
• Learn about HVP-MC3PH high voltage motor control development platform
• Spin the 3-phase PMSM motor of the HVP-MC3PH module while monitoring
the motor with the FreeMASTER tool
HVP-KV31F120M Controller Card Features
• Accommodates Target MCU MKV31F120MVLF7 MCU (ARM® Cortex®-M4 120 MHz,
512 KB flash, 2x16-bit ADCs, 3x FlexTimer, 100 LQFP)
• SWD isolation up to 5KV
• Programmable OpenSDA1 debug interface with Micro USB connector and virtual serial port
• Galvanic Isolation
• Design optimized for low noise
• On-board isolated power supply, allowing safe debugging
• Controller card allows stand-alone operation
Tools Required
• IAR Embedded Workbench V7.20.5.7624 or higher
• Freescale FreeMASTER for real-time debug monitoring and data visualization
1
Refer to the OpenSDA User Guide available at freescale.com
Page 4
Quick Start Guide
Step-by-Step Installation Instructions
2
Install the Software
and Tools
• Download and install the IDE toolchain
IAR Embedded Workbench® for ARM®
v7.20.5 or later, 30-day free evaluation
license, at iar.com/Freescale.
• Download and install the PEMicro
Windows® USB Drivers at pemicro.
com/OpenSDA.
• Download and install the free debug
monitoring and data visualization tool
Freescale FreeMASTER, v1.4 or later, at
freescale.com/FreeMASTER.
3
Program a Precompiled
Example Using the
OpenSDA MSD Application
1) Plug the USB mini cable into HVPKV46F120M. Windows will detect
a new HVP-KV31F120M drive and
automatically install the required drivers.
2) Program a Precompiled Example
“LED_demo” for the KV31
In the HVP-KV31F120M drive, copy
LED_demo.SREC file from the
Precompiled Examples folder of the
Quick Start Package. Demo will start
automatically when the download
is complete. It is not necessary to
disconnect the USB cable.
3) User LED on the controller card will blink.
4
Download Software
and Tools
Download installation
software and documentation
under “Jump Start
Your Design” at
freescale.com/HVP.
1
Page 5
5
freescale.com
Step-by-Step Installation Instructions
4
Debug Motor Control
Project in IAR with HVPMC3PH High-Voltage
Development Platform
1) Configuring Hardware
• Plug the controller card HVPKV31F120M into 64-pin PCI connector
located at HVP-MC3PH.
• Configure jumpers at HVP-MC3PH
as is shown in the table below:
Option Setting
J1 1–2, 2–3
J3 1–2, 2–3
• Close the lids.
• Connect the servo motor leads to output
connector J13. (Applications are tuned
for Servo motor type: Mige 60CSTM01330 or Maxsine 60MSLO1330FC)
• Connect mini USB cable between
daughter card and your computer.
Windows will detect a HVP-KV31F120M
debug port, mass storage device and
CDC serial port.
Page 6
6
Quick Start Guide
Step-by-Step Installation Instructions
5
Loading the PMSM Motor
Demo Software
• Launch IAR EWARM v7.20.5 and Build
the “PMSM_Sensorless_FOC”. Open
the IAR project file PMSM_Sensorless_
FOC.eww following the path build\iar\
kv31\PMSM_Sensorless_FOC\ in the
Quick Start Package.
Note: To warranty your project compatibility with the hardware
tool, select the Options: Freescale MKV31F512xxx12 as
Target Device, 512KB_Pflash.icf as Linker configuration file,
PE micro as Debug Driver, FlashKVx32K.board as Flashloader
configuration file and OpenSDA-USB as PE Micro Hardware
Interface Type.
Clean the project before selecting the action Rebuild All.
Note: The compilation may return warning messages without
consequence.
• Run IAR EWARM v7.20.5 Debug Mode
and Download and Debug the “PMSM_
Sensorless_FOC” project.
• Connect a line-isolated, current-limited
110 V DC or 90 V AC power supply to
the power input module with the IEC
connector. The power supply current
limit should be set for less than 3 amps.
The DC power supply’s polarity does
not matter. Regardless whether DC or
AC power is used, the power is always
applied to the input power connector
located on the rear panel.
• Start the debug session by selecting
the GO option from the toolbar. To spin
motor and set motor speed, continue to
following section.
Page 7
7
freescale.com
Step-by-Step Installation Instructions
6
Monitor the Project
with FreeMASTER
• Launch Freescale FreeMASTER v1.4 or
later from the Windows Start menu.
• Open the FreeMASTER project file
PMSM_FOC_KV3x.pmp following the
path freemaster\PMSM_Sensorless_
FOC in the Quick Start Package. The
PMSM Sensorless Application interface
will appear in FreeMASTER to monitor
and control the speed, the voltage and
the current consumption of the motor.
• In the Project Options, set the COM
port affected as the OpenSDA -CDC
Serial Port (information available in
Device Manager) and set the baud
rate/speed to 19200 bps (check the
option Do Not Open Port at Startup to
avoid error messages at FreeMASTER
startup).
• From the toolbar, select the action Start
the Communication.
• Select in FreeMASTER speedometer;
the requested speed and the motor will
spin automatically.
Page 8
Support
Visit freescale.com/support for a list of phone
numbers within your region.
Warranty
Visit freescale.com/warranty for complete
warranty information.
Get Started
Download installation software and documentation under
“Jump Start Your Design” at freescale.com/HVP.
For more information, visit freescale.com/HVP,
freescale.com/Kinetis, or
freescale.com/Kinetis/VSeries
Freescale, the Freescale logo and Kinetis are trademarks of Freescale
Semiconductor, Inc., Reg. U.S. Pat. & Tm. Off. Tower is a trademark of
Freescale Semiconductor, Inc. ARM and Cortex are registered trademarks
of ARM Limited (or its subsidiaries) in the EU and/or elsewhere. All rights
reserved. All other product or service names are the property of their
respective owners. © 2015 Freescale Semiconductor, Inc.
Doc Number: HVPKV31F120MQSG REV 0
Page 9
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
Freescale Semiconductor:
HVP-KV31F120M
Loading...