MODERNIZATION TO IP MADE SIMPLE
Fast Ethernet and PoE+
over Coax with up to
4,000ft (1,220m) Reach
NVT PHYBRIDGE
EC-BASE EXTENDER
DATA SHEET
EC-EXTENDER KITS
EC-Base Extender Solution
The NVT Phybridge EC Extender Solution is designed to supercharge the
downlink ports of a standard Ethernet switch delivering 10/100Mbps
symmetrical (full duplex) and PoE over Coax infrastructure with distances up
to 4,000ft (1,220m). That’s 12X the reach of standard Ethernet switches, thus
removing the costs and disruptions associated with multiple IDF closet
requirements.
With the EC Extender Solution, IP IoT devices can be connected to the
existing Coax cabling infrastructure, delivering optimal performance, while
saving cost, time, and environmental e-waste. Furthermore, the cost savings
realized by using EC Extender Solution can enable system designers to
transfer budget and resources towards higher-quality, applications and
IEEE-compliant IoT devices, including IP-enabled phones, cameras, access
control, speakers, and even facilities lighting.
Extend the reach of standard PoE switches with the
EC Extender Solution
EC-Base Paired with the EC-Link Enable 1 IP endpoint from a single long run
Coax cable with up to 30W of power
Standard PoE Switch
3 51 9 117 15 1713 21 2319 27 2925 33 3531 39 4137 45 4743
4 62 10 128 16 1814 22 2420 28 3026 34 36
32 40 4238 46 4844
NV-ECLK-BSE
SFP 1
SFP+1
EC-Base
Long Reach PoE over Coax
SFP+2
SFP 2
Local Power
Coax Cable
up to 2,000ft (610m)
Local Power
NV-LNK-02
IP ENDPOINT
Each EC Extender Kit is conveniently
packaged and includes an EC-Link+ or
EC4 Adapter, an EC-Base Extender,
and an external power supply.
1-Port EC Extender Kit
NV-ECLK-PLS-XKIT
• Extend reach of standard PoE switch
• Single port coax extender solution
enabling 1 endpoint from a single
long run Coax cable
• 10/100Mbps symmetrical (full duplex)
and PoE+ (up to 50W) with up to
4,000ft (1,220m) reach
• Up to 50W of power available for the
endpoint
• Adapters can be locally powered
• Includes: EC-Base Extender, EC-Link+
Adapter, and 60W, 55V external
power supply
• EN 50121-4 Standard for Railway/
Subway environments
4- Port EC Extender Kit
NV-EC-04-XKIT
*EC-Base Paired with the EC-Link+ Enable 1 IP endpoint from a single long run
Coax cable with up to 50W of power
Standard PoE Switch
3 51 9 117 15 1713 21 2319 27 2925 33 3531 39 4137 45 4743
4 62 10 128 16 1814 22 2420 28 3026 34 36
32 40 4238 46 4844
NV-ECLK-BSE
SFP 1
SFP+1
EC-Base
Long Reach PoE over Coax
SFP+2
SFP 2
Local Power
up to 4,000ft (1,220m)
Coax Cable
Local Power
NV-ECLK-PLS
+
EC-Link
Long Reach PoE over Coax
IP ENDPOINT
*EC-Base Paired with the EC4 Enable 4 IP endpoints from a single long run Coax
cable with up to 50W of power per port
NV-ECLK-BSE
Standard PoE Switch
3 51 9 117 15 1713 21 2319 27 2925 33 3531 39 4137 45 4743
4 62 10 128 16 1814 22 2420 28 3026 34 36
32 40 4238 46 4844
Long Reach PoE over Coax
Local Power
Coax Cable
up to 2,000ft (610m)
Local Power
SFP 1
SFP+1
EC-Base
SFP+2
SFP 2
*Pairing options available in conveniently packaged EC-Extedner Kits
NV-EC-04
IP ENDPOINT
IP ENDPOINT
IP ENDPOINT
IP ENDPOINT
• Extend reach of standard PoE switch
• Single port coax extender solution
enabling 4 IP endpoints from a single
long run Coax cable
• 10/100Mbps symmetrical (full duplex)
and PoE+ (up to 30W) with up to
2,000ft (610m) reach
• Delivers up to 30W of power per
downlink port
• Adapters can be locally powered
• Includes: EC-Base Extender, EC4,
Adapter, and 110W, 55V external
power supply
• EN 50121-4 Standard for Railway/
Subway environments
by NVT Phybridge
EC Adapter Options
There are three media converter options available to pair with the EC-Base Extender and extend PoE over Coax. The
EC-Link and EC Link+ are single endpoint solutions and the EC4 enables 4 IP endpoints from a single long Coax cable.
EC-Link
EC4EC4EC-Link+
EC-Link EC-Link+ EC4
Power
• Maximum 30W, delivered on 2pairs (spare pairs)
• Local power option
• Does not negotiate power
requirements with IP device
• Device should be IEEE 802.3 af/at
compliant
• Maximum 50W (If locally powered
and 30W if power provided from
switch) delivered on 4 pairs
• Local power option
• Adapter is IEEE 802.3af/at
compliant and will negotiate power
requirements with IP device.
• Maximu
m 50W, delivered on 4 pairs
(local power required)
• Local power option to support
greater power delivery to IP devices
• Does not negotiate power
requirements with IP device
• Device must be IEEE 802.3 af/at
compliant.
Casing Plastic Metal Plastic
EN 50121-4
Standard
Yes – approved to operate in a railway/subway environment
EC-Base Technical Specifications
Model Number
Part Number
Dimensions
Weight
Interface: Network Infrastructure side (CLEER)
Interface: IEEE Side (IP Device)
Power Supply
DC IN
(Barrel Connector)
Power Consumption
Operating Temperature
Mean Time Before Failure
Humidity
(MTBF)
EC-Base
NV-ECLK-BSE
10.09cm x 5.03cm x 2.57cm (LxWxH);
3.97” x 1.98” x 1.01” (LxWxH)
108g (3.81oz.)
1 BNC port: Coax cable (RG59, RG6, RG11)
(For General/PoE Switch)
1 RJ45 port: supports negotiation with IEEE 802.3 af/at switches
PoE from standard PoE switch, or external power supply; maximum 50W if locally powered.
Optional (sold separately)
48V – 56VDC via an external AC/DC Power Adapter (IEC Class II isolated only)
NOTE 1: Local power supply used must have its output isolated from Earth potential.
NOTE 2: If voltage of local power supply is lower than the power voltage provided from the PoE switch, then power on the PoE switch
should be turned off.
1W
-58°F to +158°F (-50°C to +70°C)
Tests conducted against international safety standard at maximum ambient temperatures of 60ºC at 30W and 55ºC at 50W
20+ years
10% to 95% (non-condensing) at 35° C
For more information, visit: www.nvtphybridge.com
NV-ECLK-BSE-6.25.2018
EC Adapters Technical Specifications
Model Number
Part Number
Dimensions
Weight
Interface: Network
I
nfrastructure side (CLEER)
Interface: IEEE Side (IP
D
evice)
Power Supply
DC IN
(Barrel Connector)
Power Consumption
Operating Temperature
Mean Time Before Failure
(MTBF)
Humidity
EC-Link EC-Link+ EC4
NV-LNK-02 NV-ECLK-PLS NV-EC-04
8.8cm x 3.2cm x 2.1cm (LxWxH);
3.46” x 1.23” x 0.83” (LxWxH)
42g (1.48oz.) 108g (3.81oz.) 96g (3.38oz.)
1 BNC port: Coax cable (RG59, RG6, RG11) 1 BNC port: Coax cable (RG59, RG6, RG11) 1 BNC port: Coax cable (RG59, RG6, RG11)
1 RJ45 port; device should be IEEE 802.3 af/at
compliant
PoE from the CLEER / EC switch or local power
from EC-Base, maximum 30W (over 2-pairs)
Optional (sold separately)
48V – 56VDC via an external AC/DC Power
Adapter with phoenix connector (IEC Class II
isolated only)
NOTE 1: Local power supply used must have its
output isolated from Earth potential.
NOTE 2: If voltage of local power supply is lower
than the power voltage provided from the PoE
switch, then power on the PoE switch should be
turned off.
0.9W 1.1W 1W
-58°F to +158°F (-50°C to +70°C)
Tests conducted against international safety standard
at maximum ambient temperatures of 50ºC
20+ years 20+ years 20+ years
10% to 95% (non-condensing) at 35° C 10% to 95% (non-condensing) at 35° C 10% to 95% (non-condensing) at 35° C
10.09cm x 5.03cm x 2.57cm (LxWxH);
3.97” x 1.98” x 1.01” (LxWxH)
1 RJ45 port; adapter is IEEE 802.3af/at compliant
and will negotiate power requirements with IP
end device.
Maximum 50W (If locally powered and 30W if
power provided from switch) delivered on 4
pairs.
Optional (sold separately)
48V – 56VDC via
Adapter (IEC Class II isolated only)
NOTE 1: Local power supply used must have its
output isolated from Earth potential.
NOTE 2: If voltage of local power supply is lower
than the power voltage provided from the PoE
switch, then power on the PoE switch should be
turned off.
-58°F to +158°F (-50°C to +70°C)
Tests conducted against international safety standard
at maximum ambient temperatures of 60ºC at 30W
and 55ºC at 50W
an external AC/DC Power
11cm x 7cm x 2.5cm (LxWxH);
4.3” x 2.75” x 0.98” (LxWxH)
4 RJ45 ports: device must be IEEE 802.3 af/at
compliant, 10/100Mbps connection to IP end
device
PoE from the CLEER / EC switch, or external
power supply; maximum 50W (over 4-pairs) each
port
Optional (sold separately)
48V – 56VDC via an external AC/DC Power
Adapter (IEC Class II isolated only)
NOTE
1: Local power supply used must have its
output isolated from Earth potential.
NOTE 2: If voltage of local power supply is lower
than the power voltage provided from the PoE
switch, then power on the PoE switch should be
turned off.
-58°F to +158°F (-50°C to +70°C)
Tests conducted against international safety standard
at maximum ambient temperatures of 50ºC
CLEER Family Compliance and Agency Approval
EMC
Safety
Environment RoHS Directive 2011/65
Emissions: FCC Part 15, ICES-003, EN 55032:2012, EN 50121-4:2015 Class A (EC-Link, EC4, EC10 and CLEER24), Class B (EC-Link+ and EC-Base)
Immunity: EN 55024:2010 ,EN 50121-4:2015
UL 60950-1 2nd Ed 2014-10-14, CAN/CSA C22.2 No. 60950-1-07 2nd Ed 2014-10
IEC 60950-1:2005+A1+A2, EN 60950-1:2006+A1+A2+A11+A12
For more information, visit: www.nvtphybridge.com
NV-ECLK-BSE-6.25.2018
Loading...