NVT NV-CLR-024-DEMO Installtion Instruction

QUICK INSTALL GUIDE - CLEER24

The CLEER (Coax Leveraged Ethernet Extended Reach) family of data switches
delivers Ethernet and Power over Ethernet over Coax cable with multiple times
the reach of traditional data switches. With the CLEER24 switch customers can
transform their existing Coax infrastructure for IP device deployment.

NOTE: Please see page 3 for important safety instructions

CLEER24

Optic Ports

Gbic 1

Gbic 2 GbE 2

2 10/100/1000 Base-T

Ethernet Ports

Management (MGMT) &

GbE 1

Removable Power Supply

RUN

ALARM

FAULT

Status LEDs

2 Mini-Gbic Fiber

Reset

Reset

Installation Details

System Grounding: See Page 5

Location and Regional Specifications:

The CLEER24 can be installed in any indoor location in all countries except in
Finland, Norway and Sweden, where, in these 3 Nordic countries, it must be
installed in a restricted access location.

CLEER24

Console Port

Mgmt

Console

24 BNC Female Connectors

5

3

1

4 6 8

2

1

2

7

9

10

109876543

11

Network Infrastructure

BNC Port

CLEER24 kan installeres overalt indendørs undtagen i Finland, Norge og

Sverige, hvor i disse tre nordiske lande den skal installeres på et sted med
begrænset adgang.

11

12

13

12

24 Downlink
Status LEDs

13

14

15

14

15

16

17

18 20

19

2019181716

EC-LINK

21

22

2221

CLEER Package Includes:

23

24

23

24

1 x Rackmount Bracket Kit

1 x Console Cable

1 x Quick Install Guide

EC-Link Package Includes:

Ethernet Side

RJ45 Port

1 x CLEER24 Unit

1 x Power Cable

2 x EC-Links

CLEER24 kan installeras på valfri plats inomhus i samtliga länder utom Finland,
Norge och Sverige; i dessa nordiska länder måste den installeras på en plats
med begränsad åtkomst.

CLEER24 kan installeres innendørs i alle land unntatt Finland, Norge og Sverge.

I disse tre nordiske landene må den installeres på et sted med begrenset
tilgang.

Space Requirements:

1. Select a standard 19" equipment rack or, for a standalone installation, a flat, stable surface capable of supporting the size and weight of the CLEER24, its
installable components and cabling.

2. Ensure that you have enough rack space for all equipment. Shelves and rear supporting brackets are not mandatory.

Location Requirements:
Power - The CLEER24 switch must be placed within 6 feet of an available power source. Do not use an extension cord to connect the equipment to a power
outlet.
Ventilation - To ensure proper ventilation of the CLEER24, leave at least 2 inches of unobstructed space on all sides of the unit. If the fans are blocked, the unit
could overheat.
Downlink – The EC-Link adapters should be installed a minimum of 6 feet away from the CLEER24 switch.

Installation procedures will be trouble‐free if you ensure that the following items are available before you begin:

• The CLEER24 switch, all cables and accessories you received in the CLEER package.

• All EC-Link required for connecting the IP endpoint devices, provided with the product package according to the quantity ordered.

• SFP transceiver modules for the Gbic uplink trunks if connecting over fiber.

• Fiber optic LAN cables for the Gbic uplink trunks (user-supplied) if connecting over fiber.

• Standard CAT5e copper LAN cables for the GbE uplink trunks (user‐supplied).

• Coax cable for the downlink ports (user-supplied).

• Serial console cable for the CONSOLE port, provided with the product package.

• Standard CAT5e copper LAN cable for the MGMT port (optional). Only needed if out-of-band management is required (user‐supplied).

HARDWARE TOPOLOGY AND INSTALLATION OVERVIEW

1. Remove the CLEER24 switch and all accompanying accessories.

2. Install the rackmount brackets for rack mounting. Unit fits in standard 19” racks.

3. Install the protective grounding conductor (please refer to the System Grounding

section of this guide).

4. Remove all legacy cameras or phones from the Coax cable.

Note: It is extremely important that non-IP, non-PoE cameras are not connected
when you power on the CLEER24.

5. Connect EC-Link to the Network jack on the IP endpoint and connect the BNC
Jack on the EC-Link to the Coax cable.

6. Connect the Coax cable to BNC connectors on the CLEER24 switch.

or Server

7. Connect the uplink cable from a Gigabit port to the NVR or network switch.
Note: This connection also permits in-band management over Ethernet when
bridged mode is disabled (non-default setting).

8. For power share, daisy chain CLEER24 switches using DC cables (see below).

9. Power up the CLEER24.

10. To revert back to factory defaults, hold the reset button for at least 10 seconds.
Note: In band management will be enabled after a factory reset. This can be

disabled using the pal-set-bridged outband command.

To NVR

CLEER24 Managed Switch

RUN

ALARM

FAULT

CAT5

1 357

GbE 1

Mgmt

Gbic 1

468

2

Console

Gbic 2 GbE 2

21

Reset

NVR

The Most Robust PoE Capabilities
on the Market

Four switches can be stacked together for power
sharing, load balancing and power redundancy. The
CLEER24 switch comes standard with PowerWISE
technology.

9 11 13

101214

109876543

15

17 192123

16

18 20

22 24

2019181716151413

24232221

1211

Coax Up to 600M
100MB With PoE

Copyright 2019 NVT Phybridge | 413-0001-F | Page 1888.901.3633 | [phone] | www.nvtphybridge.com

Endpoint

Endpoint

Endpoint

Endpoint

Endpoint

QUICK INSTALL GUIDE

POWER CAPABILITIES AND CONSIDERATIONS

CLEER24 switches come standard with a hot swappable PowerWise power supply for power/load sharing. The switch will support either an AC or DC power

source.

The switches are amongst the lowest power consuming switches in the industry.

For a redundant power configuration, daisy-chain multiple CLEER24 switches:

You can connect up to a maximum of 4 units for power/load sharing.

• Mount all CLEER24 switches in the same equipment rack, with no more than 1U space
between any two units.

Note: You can daisy-chain the units together while they are up and running or power them up
afterward.

• Facing the rear of the units, install the DC cables (available through NVT Phybridge) as follows:

Note: To fit properly, the DC cable must be inserted into the DC input/output connector with

its hairpin clip on top.

• For the top unit, insert the first cable into the DC input connector on the left until it clicks into

place. Bring the other end of the cable down to the next unit, and connect to the DC output
connector on the right.

• Continue in the same way for each pair of units, connecting the DC input (left) connector on

the upper unit to the DC output (right) connector on the lower unit.

Important: For the bottom unit, the last cable from the DC input (left) connector goes up to
the DC output (right) connector on the top unit. This is required to create a fully redundant

ring.

Note: If you need to move a cable to to a different DC connector on the CLEER24, press the

hairpin clip at the top of the DC cable and pull the cable out.

CONFIGURING THE CLEER24 (2 METHODS)

Connecting to the Admin GUI

Default IP Address:

• MGMT = 192.168.1.1

• GBE1 & GBE2 = 192.168.100.1

Default User Name & Password:

• User Name: admin

• Password: admin

Connecting to CLEER24:

1. Change the IP address of your PC or Laptop to

192.168.1.2

2. Connect your Ethernet port on the PC or Laptop to the
MGMT port on the CLEER24.

3. Open a web browser that is up to date and type in/go
to http://192.168.1.1

4. Login is “admin” password is “admin” (without quotes)

5. You are now in the Admin GUI.
NOTE: Change IP addresses to avoid conflict.

(Ethernet/Uplink Ports)

Steps to Change the IP Address:

1. Click on Ethernet menu option on the top bar.

2. Once Ethernet page is displayed select UPLINK
PORTS.

3. Type in new IP address in the IP Address section for IP
configuration.

4. Type in new Net Mask in the Net Mask section (e.g.

255.255.255.0).

5. Type in new IP address of the system default gateway

in the Default Gateway section.

6. Click Save Changes button to apply the modifications.

7. Refer to admin guide for more software details.

IN

IN

OUT

OUT

IN

IN

OUT

OUT

IN

OUT

IN

OUT

Steps to Change the IP Address:

1. Type in “pal-set-sys-ip GbE 192.168.9.1 255.255.255.0

192.168.9.255” Substitute the provided example IP
information for your own.
a. The usage is: pal-set-sys-ip GbE <IPADDRESS>
<NETMASK> <BROADCAST>

2. You will be prompted to confirm this information.

3. Refer to the CLI section of the administration guide for
more information.

Accessibility:

• Console cable connected directly to the console port.

Console Port Serial Settings:

• 115200/8/N/1

Default User Name & Password:

• User Name: admin

• Password: admin

Connecting to the Command Line Interface (CLI)

Connect to the Console Port:

1. Connect the RJ45 end of the serial cable to the console
port of the CLEER24. Connect the serial end of the
serial cable to the serial port of your PC.

2. Configure your serial port to 115200/8/N/1.

3. Login is “admin”, password is ”admin” (without quotes)

4. You are now connected to the CLI via the console port.

Changing Management Port Default IP Address

The Mgmt IP default address of 192.168.1.1 may conflict with other CLEER24s. To prevent this from happening, you must change the IP address of the Mgmt Port to an IP which
will never be used on the network. For example, if your network belongs to the “192.168.X.X” subnet, change the Mgmt Port IP to “10.10.1.1”.

Steps to Change the Management Port IP Address:

1. Log into the unit via the serial console port (115200,8,N,1,None).

2. Type in “pal-set-sys-ip mgmt 10.10.1.1 255.255.255.0 10.10.1.255”
Substitute the provided example IP information for your own.
a. The usage is: pal-set-sys-ip mgmt <IPADDRESS> <NETMASK> <BROADCAST>

3. You will be prompted to confirm this information.

4. Refer to the CLI section of the administration guide for more information.

Copyright 2019 NVT Phybridge | 413-0001-F | Page 2888.901.3633 | [phone] | www.nvtphybridge.com

QUICK INSTALL GUIDE

NOTE THE FOLLOWING:

All of the above instructions provide basic installation information necessary for the proper and safe functioning of this equipment. Persons installing or maintaining
this product must read all of the safety instructions and the parts of system grounding, which are applicable to the system being maintained. Only trained, qualified
service personnel shall install or maintain this product.

WARNINGS

FAILURE TO FOLLOW ALL INSTRUCTIONS MAY RESULT IN IMPROPER EQUIPMENT OPERATION AND/OR RISK OF ELECTRICAL SHOCK.

ANY CONNECTION TO AN OUTSIDE PLANT LEAD, AN OFF-PREMISE APPLICATION, OR ANY OTHER EXPOSED PLANT APPLICATION MAY
RESULT IN A FIRE OR SHOCK HAZARD, AND/OR DEFECTIVE OPERATION, AND/OR EQUIPMENT DAMAGE.

Keep these instructions with the equipment.
Do not attempt to install or service this equipment unless you are skilled in the installation and maintenance of electronic telecommunications equipment and
have successfully completed specific training for this equipment.

SAFETY WARNINGS AND PRECAUTIONS

• Access to the interior of this unit shall be made only by a qualified technician.

• This unit may have more than one power input. To reduce the risk of energy or shock hazard, disconnect all power inputs before servicing.

• To ensure adequate cooling of the equipment, a 2-inch unobstructed space must be provided around all sides of the unit.

• The Power Socket shall be installed near the equipment and shall be easily accessible

• To prevent the risk of shock or fire hazard, replace fuse with same type and rating.
CAUTION: The ground lug is a main earth terminal that must be permanently connected to earth.

• Der Zugang ins Innere des Gerätes ist nur einem fachlich qualifizierten Techniker gestattet.

• Dieses Gerät kann mehr als eine Leistungsaufnahme. Um das Risiko von Energie oder Gefahr eines elektrischen Schlags zu reduzieren, trennen Sie alle Macht
Eingaben, bevor Wartungsarbeiten an der Einheit.

• Um die Kühlung des Gerätes nicht zu beeinträchtigen, ist es notwendig, an allen Seiten des Gerätes ca 5 cm Raum zu lassen.

• Stellen Sie das Gerät in der Nähe eines geerdeten Schutzkontaktsteckers so auf,dass der Stecker leicht erreichbar und zugänglich ist.

• Zur Vermeidung der Stromschlag‐und Feuergefahr beim Auswechseln Sicherungen des gleichen Typs und der gleichen Nennleistung einsetzen.

VORSICHT: Die Erdungsöse ist einer der wichtigsten Erdungsklemme, die dauerhaft auf die Erde angeschlossen werden muss.

• Seul un spécialiste doit avoir accès l'appareil.

• Cette unité peut avoir plus d'une entrée d'alimentation. Pour réduire le risque de danger de l'énergie ou de choc, débranchez toutes les entrées
d'alimentation avant de réparer l'unité.

• Afin de ne pas nuire au processus de refroidissement, il est nécessaire de laisser un espace d'environ 5 cm de chaque côté de l'appareil.

• Placez l'appareil près d’une prise de courant facilement accessible.

• Afin d’éviter tout risque d’incendie ou d’électrocution, remplacez les fusibles par des fusibles de même type et de même ampérage.

ATTENTION: La cosse de terre est une borne de terre principale qui doit être connectée en permanence à la terre.

• El servicio de antenimiento y reparación de esta unitad solo puede ser realizado por técnicos autorizados por el fabricante.

• Esta unidad puede tener más de una entrada de energía. Para reducir el riesgo de peligro de descargas eléctricas o descargas eléctricas, desconecte todas las
entradas de alimentación antes de reparar la unidad.

• No bloquee las ranuras de ventilación del equipo, ya que los componentes podrian sobrecalentarse y sufrir daños.

• Para evitar el riesgo de choque electrico o de incendio, reemplace el fusible com otro del mismo tipo y capacidad nominal.

• Para su propia protección, cerciórese de que todas las conexiones eléctricas de los servicios públicos, incluyendo la puesta a tierra, las líneas telefónicas y el
sistema de tuberías de agua metálicas internas, si las hubiera, estén conectadas entre sí.

PRECAUCIÓN: El terminal de tierra es un terminal de tierra principal que debe estar permanentemente conectada a la tierra.

• L'accesso all'interno di questa unità `deve essere effettuata solo da un tecnico qualificato.

• Questo unisce possono avere più di un ingresso di potenza. Per ridurre il rischio di pericolo di energia o scosse, scollegare tutti gli ingressi di alimentazione
prima di.

• Per garantire un adeguato raffreddamento dell'apparecchiatura, uno spazio libero da 2 pollici deve essere fornita intorno a tutti i lati dell'unità.

• The Power Socket `deve essere installata vicino all'apparecchio e` devono essere facilmente accessibili

• Per evitare che la prevenzione del rischio di scossa o di pericolo di incendio, sostituire il fusibile con lo stesso tipo e valore.

ATTENZIONE: Il capocorda è mano che il terminale di terra deve essere collegato a terra in modo permanente.

• Достъп до вътрешността на този уред трябва да се извършва само от квалифициран техник.

• Това устройство може да има повече от един вход. За да намалите риска от опасност от електрически или токов удар, изключете всички входове за
захранване преди извършване на сервиз.

• За да се осигури подходящо охлаждане на оборудването, трябва да се осигури 2-инчово свободно пространство около всички страни на устройството.

• Захранващият щепсел ще бъде инсталиран в близост до оборудването и ще бъде лесно достъпен

• За да предотвратите опасност от удар или пожар, сменете предпазителя със същия тип и квалификация.

ВНИМАНИЕ

: Заземената ухо е основна заземяваща клема, която трябва да бъде постоянно свързана към земята.

• Juurdepääs interjööri selle üksuse tehakse ainult kvalifitseeritud tehnik.

• See üksus võib olla rohkem kui üks võimsustoide. Et vähendada energia või elektrilöögi vältimiseks lahutage kõik sisendvõimsus Enne hooldamist.

• Jahutuse tagamiseks seadme, 2-tolline vaba ruum peab olema ümber kõik küljed üksus.

• Pistikupesa peab olema seadme lähedal ning olema kergesti ligipääsetavad

• Selleks, et vältida riski ning tulekahjuoht, vaheta kaitse sama tüüpi ja hinnang.

ETTEVAATUST: Maapind kõrv on peamine Maa terminal peab olema püsivalt ühendatud maaga.

Copyright 2019 NVT Phybridge | 413-0001-F | Page 3888.901.3633 | [phone] | www.nvtphybridge.com