NVT NV-8PS13-PVD Specsheet
Model NV-8PS13-PVD
Power Supply Passive Video Receiver Hub
Front
Rear
Features:
• Provides Class 2 SELV camera power while receiving video transmission
and delivering P/T/Z telemetry all over a single 4-pair Cat5e cable
• Standard telecom/datacom structured cabling pinouts per EIA/TIA 568B
• Independently selectable 24VAC-OFF-28VAC with 1 Amp per channel
• Automatic-reset fault protection; transient protection
• Individually floating outputs ensure total ground-loop immunity
• Diagnostic LEDs show load/no load, miswires, and overload conditions
• Use with the NV-216A-PV, NV-218A-PVD, or NV-226J-PV transceiver at the camera
• Power cameras via UTP over significant distances (see Power Distance Chart)
• 1U high; 8" deep; wall, desk, or rack-mountable, 2ft (60cm) BNC Cables included
• Limited lifetime warranty
The 8-channel NV-8PS13-PVD is a key hybrid component that consolidates all CCTV system cabling
using standard EIA/TIA 568B structured building wiring. Designed for installation in the IDF/Telecom
Closet or MDF/Equipment Room, the Power Supply Passive Video Receiver Hub has independently
selectable 24VAC-OFF-28VAC outputs that can support at-distance camera loads up to 1 Amp per channel. Use with NVT’s PVDTMtransceivers for cable runs under 750ft (225m). A built-in passive receiver hub
allows connection to DVR or an encoder for IP transmission. Per-channel diagnostic LEDs display load
/no-load, miswires, or fault conditions at a glance. Automatic-reset fault protection, transient protection,
and ground loop free individually floating outputs.
Network Video Technologies
4005 Bohannon Drive • Menlo Park, CA 94025 • USA
(+1) 650.462.8100 • 800.959.9870 • FAX (+1) 650.326.1940
nvt.com • info@nvt.com
-38-
Model NV-8PS13-PVD
Power Supply Passive Video Receiver Hub
Technical Specifications
W I R E D I S T A N C E (Power Distance Charts)
Supply voltage, wire resistance and minimum camera operating
voltage determine the maximum camera distance. Examples
assume a minimum 21VAC at the camera:
C A M E R A P O WE R
Each camera is powered by a fully isolated (floating) Class 2 SELV
output, individually switchable 24VAC / OFF/ 28VAC at up to 1 Amp.
Each output is individually thermistor protected.
P O W E R I N P UT
Power inlet IEC•with molded power cord (included)
Voltage 115 / 230VAC
Current 2.5 / 1.25 Amps
Protection 5x20mm type T fuse 2.5Amp 250V
Wattage 250 Watts
Heat (power supply only) 100 BTU / Hour
(power supply with cameras) 900 BTU / Hour
P O W E R O U T PU T
Each camera is powered by a fully isolated (floating) Class 2 SELV
ouput, individually switchable 24VAC / off / 28VAC at up to 1 Amp.
Each output is individually thermistor protected for auto-reset after
fault removal.
F R O N T P A N E L L E D s
System Power: Blue LED
Per-channel LED Indicates:
Off: No load connected
Green: Load connected and working
Amber: Mis-wiring detected
Red: Overload fault condition
Notes: Wire should be Cat5 or better/ low voltage camera power, video and RS-422
or RS-485 data may reside within the same wire bundle, however do not run 24 or
28VAC within the same wire bundle as other telecom or datacom signals.
V I D E O
Frequency response DC to 5 MHz
Attenuation 0.5 dB typ
Common-mode / Differential-mode rejection
15 KHz to 5 MHz 60 dB typ
Impedance
Coax, female BNC 75 ohms
UTP, RJ45 100 ohms
Network Wiring One four-pair Cat5 or better per channel
E N V I R O N ME N TA L
Ambient Temperature -4 to +122 °F (-20 to +50 °C)
Minimum airflow 20ft
Humidity (non-condensing) 0 to 95%
Transient Immunity per ANSI / 587 C62.41
3
/min (0,5m3/ min)
M E C H A N I CA L
Dimensions, including connectors
Weight 14lb (6,35kg)
19in wide, 1.73in high, 12in deep
43cm wide, 4,5cm high, 20cm deep
A C C E S S O RI E S (included)
Mounting Rack mount “L” brackets for front,
Cables Eight 2ft (60cm) coax jumpers
Molded IEC•power inlet cord 7ft (200cm)
rear, or wall installations;
rubber feet for desk applications
O P T I O N A L EQ U I P M E N T
Mounting NV-RMBK2 Rear Mount Support Kit
NV-WMBK2 Wall Mount Bracket Kit (heavy duty)
(designed for use with thinner
metal equipment racks)
R E G U L AT O R Y
Network Video Technologies
4005 Bohannon Drive • Menlo Park, CA 94025 • USA
(+1) 650.462.8100 • 800.959.9870 • FAX (+1) 650.326.1940
nvt.com • info@nvt.com
-39-
Loading...