Model NV-4PS13-PVD
Power Supply Passive Receiver Hub
Front
Rear
Features:
• Provides Class 2 SELV camera power while receiving video transmission and
delivering P/T/Z telemetry all over a single 4-pair Cat5e cable
• Standard telecom/datacom structured cabling pinouts per EIA/TIA 568B
• Independently selectable 24VAC-OFF-28VAC with 1 Amp per channel
• Automatic-reset fault protection; transient protection
• Individually floating outputs ensure total ground-loop immunity
• Diagnostic LEDs show load/no load, miswires, and overload conditions
• Use with the NV-216A-PV, NV-218A-PVD or the NV-226J-PV transceiver at the camera
• Power cameras via UTP over significant distances (see Power Distance Chart)
• 1U high x 8” deep wall, desk or desk rack-mountable
• Limited lifetime warranty
The 4-channel NV-4PS13-PVD is a key hybrid component that consolidates all CCTV system cabling
using standard EIA/TIA 568B structured building wiring. Designed for installation in the IDF/Telecom
Closet or MDF/Equipment Room, the Power Supply Passive Video Receiver Hub has independently
selectable 24VAC-OFF-28VAC outputs that can support at-distance camera loads up to 1 Amp per channel. Use with NVT’s PVDTMtransceivers for cable runs under 750ft (225m). A built-in passive receiver hub
allows connection to DVR or an encoder for IP transmission. Per-channel diagnostic LEDs display load
/no-load, miswires, or fault conditions at a glance. Automatic-reset fault protection, transient protection,
and ground loop free individually floating outputs.
Network Video Technologies
4005 Bohannon Drive • Menlo Park, CA 94025 • USA
(+1) 650.462.8100 • 800.959.9870 • FAX (+1) 650.326.1940
nvt.com • info@nvt.com
-35-
Model NV-4PS13-PVD
Power Supply Passive Receiver Hub
Technical Specifications
WIRE DISTANCE (Power Distance Charts)
Supply voltage, wire resistance and minimum camera operating
voltage determine the maximum camera distance. Examples
assume a minimum 21 VAC at the 24 VAC camera:
CAMERA POWER
Each camera is powered by a fully isolated (floating) Class 2 SELV
output, individually switchable 24VAC / OFF/ 28VAC at up to 1 Amp.
Each output is individually thermistor protected.
POWER INPUT
Power inlet IEC with molded power cord (included)
On-off switch Rear panel
Voltage 115 / 230 VAC
Current 1.25 / 0.625 Amps
Frequency 50 / 60 Hz
Protection 2.5A slo-blo 8x20mm fuse and thermal shutdown
Wattage 125 Watts
Heat (power supply only) 50 BTU/hour
(power supply with cameras) 420 BTU/hour
FRONT-PANEL LEDs
Blue LED System power on
Per-channel LED indicates: Off No load connected
Green Load connected and working
Amber Mis-wiring detected
Red Overload shutdown condition
ENVIRONMENTAL
Ambient Temperature -4 to 122 °F (-20 to +50 °C)
Minimum airflow 4 ft3/min (0,1m3/min)
Humidity (non-condensing) 0 to 95%
Transient Immunity per ANSI 587 C62.41
Notes: Wire should be Cat5 or better/ low voltage camera power, video and RS-422
or RS-485 data may reside within the same wire bundle, however do not run 24 or
28VAC within the same wire bundle as other telecom or datacom signals.
VIDEO
Frequency response DC to 5 MHz
Attenuation 0.5 dB typ
Common-mode / Differential-mode rejection
15 KHz to 5 MHz 60 dB typ
Impedance
Coax, female BNC 75 ohms
UTP, RJ45 100 ohms
Network Wiring One four-pair Cat5 or better per channel
Network Video Technologies
4005 Bohannon Drive • Menlo Park, CA 94025 • USA
(+1) 650.462.8100 • 800.959.9870 • FAX (+1) 650.326.1940
nvt.com • info@nvt.com
MECHANICAL
Dimensions 9.25in wide, 1.75in high, 7.25in deep
including connectors: (235mm wide, 44,5mm high, 184mm deep)
Weight 7lb (3,2kg)
Mounting Wall, or desk mount
REGULATORY
Specifications subject to change without notice.
-36-