NVT NV-4PS10-PVD Specsheet

Model NV-4PS10-PVD

NEW!

Power Supply Cable Integrator Hub

Front

Rear

Features:

• Provides Class 2 SELV camera power and pass-through video and telemetry data
connectivity for up to 4 cameras, each via a single RJ45 4-pair UTP cable

• Standard telecom/datacom structured cabling pinouts per EIA/TIA 568B

• Independently selectable 24 or 28VAC with 1 Amp max per channel

• Automatic-reset fault protection; transient protection

• Individually floating outputs ensure total ground-loop immunity

• Diagnostic LEDs show load/no load, miswires, and overload conditions

• Use with the NV-216A-PV, NV-218A-PVD or the NV-226J-PV transceiver at the camera

• Power cameras via UTP over significant distances (see Power Distance Chart)

• 1.75” high x 7.25” deep x 9.25” wide, wall or desk mount

• Limited lifetime warranty

The NVT Model NV-4PS10-PVD combines a 1 Amp/channel power supply with pass through video and
telemetry data, for up to 4 cameras, all over UTP wire. Designed for installation in the wiring/IDF tele­com closet, or at the Control/MDF room, the NV-4PS10-PVD consolidates connectivity vial standard
4-pair RJ45 EIA/TIA 568B compliant premises wiring and pinouts.

At the camera, Power, Video and Data connections are made using a PVDTMtransceiver via an RJ45
connector and a single 4-pair cable. Control/MDF room connections are achieved with a single 4-pair
RJ45 cable for each group of four cameras. P/T/Z telemetry data, if required, passes through the
NV-4PS10-PVD’s data path and is connected to the controller via a second 4-pair RJ45 cable.

Network Video Technologies

4005 Bohannon Drive • Menlo Park, CA 94025 • USA

(+1) 650.462.8100 • 800.959.9870 • FAX [phone]

nvt.com • [e-mail]

-29-

Model NV-4PS10-PVD

Power Supply Cable Integrator Hub

Technical Specifications

WIRE DISTANCE (Power Distance Charts)

Supply voltage, wire resistance and minimum camera operating
voltage determine the maximum camera distance. Examples
assume a minimum 21 VAC at the 24 VAC camera:

CAMERA POWER

Each camera is powered by a fully isolated (floating) Class 2 SELV
output, individually switchable 24VAC / OFF/ 28VAC at up to 1 Amp.
Each output is individually thermistor protected.

POWER INPUT

Power inlet IEC with molded power cord (included)
On-off switch Rear panel
Voltage 115 / 230 VAC
Current 1.25 / 0.625 Amps
Frequency 50 / 60 Hz
Protection 2.5A slo-blo 8x20mm fuse and thermal shutdown
Wattage 125 Watts
Heat (power supply only) 50 BTU/hour

(power supply with cameras) 420 BTU/hour

FRONT-PANEL LEDs

Blue LED System power on
Per-channel LED indicates: Off No load connected

Green Load connected and working
Amber Mis-wiring detected
Red Overload shutdown condition

ENVIRONMENTAL

Ambient Temperature -4 to 122 °F (-20 to +50 °C)
Minimum airflow 4 ft3/min (0,1m3/min)
Humidity (non-condensing) 0 to 95%
Transient Immunity per ANSI 587 C62.41

Notes: Wire should be Cat5 or better/ low voltage camera power, video and RS-422
or RS-485 data may reside within the same wire bundle, however do not run 24 or
28VAC within the same wire bundle as other telecom or datacom signals.

Network Video Technologies

4005 Bohannon Drive • Menlo Park, CA 94025 • USA

(+1) 650.462.8100 • 800.959.9870 • FAX [phone]

nvt.com • [e-mail]

MECHANICAL

Dimensions 9.25in wide, 1.75in high, 7.25in deep
including connectors: (235mm wide, 44,5mm high, 184mm deep)
Weight 7lb (3,2kg)
Mounting Wall, or desk mount

REGULATORY

Specifications subject to change without notice.

-30-