NVT NV-413A Specsheet

Model NV-413A

4-Channel Video Transceiver

Features:

• Four passive transceiver channels in one product

• Full-motion CCTV video at distances up to 750ft (225m) when used
with a passive NVT transceiver or hub

• Up to 3,000 feet (1,000 m) with a DigitalEQTMHub or active receiver

• Up to 1,500 feet (460m) shall be supported by any NVT StubEQTMHub

• Supports pluggable screw terminal or RJ45 connections

• No power required

• Exceptional interference rejection

• Built-in transient protection

• Supports “up-the-coax” type control signal up to 750ft (225m)

• Compatible with qualified UTP cameras

• Two NV-413As may be rack mounted using the NV-RM8/10 Rack Panel Kit

• Limited lifetime warranty

The NVT Model NV-413A 4-channel Video Transceivers is a passive (non-amplified) device that allows
the transmission of real-time monochrome or color video over Unshielded Twisted-Pair (UTP) telephone
wire. Baseband (composite) signals of any type are supported.

“Up-the-coax” type signal may be sent over the same wire pair. Used as a receiver, the NV-413A is fully
compatible with qualified cameras that are equipped with an NVT twisted-pair output.

The unparalleled interference rejection and low emissions of the Model NV-413A allow video signals to
co-exist in the same wire bundle as telephone, datacom, or low-voltage power circuits. This allows the
use of a shared or existing cable plant. With built-in transient protection, damaging voltage spike prob­lems are eliminated.

Network Video Technologies

4005 Bohannon Drive • Menlo Park, CA 94025 • USA

(+1) 650.462.8100 • 800.959.9870 • FAX [phone]

nvt.com • [e-mail]

-51-

1+
2

-

3+
4

-

5+
6

-

7+
8

-

Ch. 1

Ch. 4

Ch. 3

Ch. 2

Model NV-413A

4-Channel Video Transceiver

Technical Specifications

V I D E O

Frequency response DC to 5 MHz
Attenuation 0.5 dB typ
Common-mode / Differential-mode rejection

15 KHz to 5 MHz 60 dB typ

Impedance

Coax, female BNC 75 ohms
UTP, Screw terminal block or RJ45 100 ohms

W I R E T Y P E

Network Wiring One Unshielded Twisted Pair

(for each video signal)

24-16 AWG (0,5-1,31mm)
Category Type 2 or better
Impedance 100 ± 20 ohms
DC Loop Resistance 52 ohms per 1,000ft

(18 ohms per 100m)

Differential Capacitance 19 pF/ft max

(62 pF/m max)

Typical Application

Passive to Passive Application up to 750ft (225m)

C O N N E C T O R S

Use either terminal or RJ45 (not both)

P O W E R

No external power required

E N V I R O N M E N TA L

Ambient ambient temperature -22 to +167 °C (-30 to +75 °C)
Humidity (non-condensing) 0 to 95%
Transient Immunity per ANSI / IEEE 587 C62.41

M E C H A N I C A L

Dimensions, excluding brackets and connectors

7.3 x 2.35 x 1.65in (184 x 60 x 41mm)
Weight 12.0oz (340g)
Material Black ABS
Mounting Two 0.175 in (4,4mm) diameter holes

6.75in (171,5mm) apart
Two NV-413As can be mounted to an NV-RM 8/10 Rackmount
Panel

Specifications subject to change without notice.

NV-208A-M

Punch

block
(IDF)

Backbone

Punch

block
(IDF)

NV-413A

Monitor

DVR / NVR

IP

Network Video Technologies

4005 Bohannon Drive • Menlo Park, CA 94025 • USA

(+1) 650.462.8100 • 800.959.9870 • FAX [phone]

nvt.com • [e-mail]

-52-

Copyright © 2009 NVT, Inc.

411-763-1-H