NVT NV-16PS42-PVD Specsheet
Model NV-16PS42-PVD
16-Channel Power Supply StubEQTMActive Receiver Hub
Front
Rear
Features:
• Provides Class 2 SELV 28 VAC with up to 1 Amp/channel while receiving video transmission
and delivering P/T/Z telemetry, all over a single 4-pair Cat5 cable for each camera
• Built-in distribution amplifier with 2 video outputs per channel
• Full motion CCTV video at distances up to 1,500ft (460m) when used with any passive
NVT transceiver
TM
• Adaptive StubEQ
time, no manual adjustments required
fully automatic 2-band equalization provides adjustment free equalization every
• Automatic-reset fault protection; transient protection
• Individually floating power outputs and differential video inputs ensure total ground-loop immunity
• Diagnostic LEDs show load/no load, miswires, overload conditions, and video status
• Limited lifetime warranty
The 16-channel NV-16PS42-PVD is a key hybrid component that consolidates all CCTV system cabling using standard
EIA/TIA 568B structured building wiring. Designed for installation in the IDF/Telecom Closet or MDF/Equipment Room, Power
Supply StubEQ
Amp per channel for cable runs up to 1,500ft (460m). A built-in StubEQ
TM
Active Receiver Hubs have individual floating 28VAC outputs that support at-distance camera loads up to 1
TM
video receiver hub ensures a zero loss video signal for connection into a DVR or IP encoder. Standard features include: automatic-reset fault protection, transient protection,
ground loop free individually floating outputs and power and video diagnostics. All NVT products are UL and cUL listed, are
compliant with CE, RoHS, WEEE, and come with NVT’s lifetime warranty.
Model NV-16PS42-PVD
Fixed Camera 24VAC only, used with NV-216A-PV
Power Supply Voltage
Minimum Voltage at Camera
789ft (240m)
994ft (303m)
393ft (120m)
495ft (151m)
262ft (80m)
331ft (101m)
1,840ft (561m)
2,320ft (707m)
916ft (279m)
1,155ft (352m)
612ft (186m)
771ft (235m)
B&W Camera, 2.4 W
2-pair 24 AWG
2-pair 23 AWG
Color Camera, 4.8 W
2-pair 24 AWG
2-pair 23 AWG
Color Camera, 7.2 W
2-pair 24 AWG
2-pair 23 AWG
24 VAC
21 VAC
28 VAC
21 VAC
Fixed 12VDC Camera used with NV-226J-PV
Power Supply Voltage
1,586ft (748m)
1,999ft (609m)
795ft (242m)
1,002ft (306m)
2,220ft (677m)
2,799ft (853m)
1,113ft (339m)
1,403ft (428m)
B&W Camera, 2.4 W
2-pair 24 AWG
2-pair 23 AWG
Color Camera 4.8 W
2-pair 24 AWG
2-pair 23 AWG
24 VAC
28 VAC
P/T/Z 24VAC Camera used with NV-218A-PVD
Power Supply Voltage
Minimum Voltage at Camera
90ft (27m)
113ft (35m)
210ft (64m)
265ft (81m)
P/T/Z Camera, 21 W
2-pair 24 AWG
2-pair 23 AWG
24 VAC
21 VAC
28 VAC
21 VAC
Fixed Dual Voltage 24VAC/12VDC Camera with NV-216A-PV
Power Supply Voltage
Minimum Voltage at Camera
1,753ft (534m)
2,210ft (674m)
874ft (266m)
1,102ft (336m)
583ft (178m)
735ft (224m)
2,454ft (748m)
3,094ft (943m)
1,223ft (373m)
1,542ft (470m)
816ft (249m)
1,029ft (314m)
B&W Camera, 2.4 W
2-pair 24 AWG
2-pair 23 AWG
Color Camera, 4.8 W
2-pair 24 AWG
2-pair 23 AWG
Color Camera, 7.2 W
2-pair 24 AWG
2-pair 23 AWG
24 VAC
14 VAC
28 VAC
14 VAC
16-Channel Power Supply StubEQTMActive Receiver Hub
Technical Specifications
R E C O MM E N DE D W I R E DI S TA NC E
Supply voltage, wire resistance and minimum camera operating
voltage determine the maximum camera distance. Examples
assume a minimum 21VAC at the camera:
V I D E O
Frequency response DC to 10 MHz
Attenuation 0.5 dB typ
Common-mode / Differential-mode rejection
15 KHz to 5 MHz 60 dB typ
Impedance
Coax, female BNC 75 ohms
UTP, RJ45 100 ohms
Network Wiring One four-pair Category cable
C A M E RA P O WE R
Each camera is powered by a fully isolated (floating) 28 VAC Class 2
SELV output at up to 1 Amp. Each output is individually thermistor
protected for auto-reset.
P O W E R
Power inlet IEC with molded power cord (included)
Voltage 115 / 230V
Current 3.0 / 1.5 Amps
Protection 5x20mm type T fuse 5 Amp 250V
Wattage 500 Watts
Heat (NV-16PS42-PVD only) 275 BTU / Hour
(NV-16PS42-PVD with cameras) 2,000 BTU / Hour
E N V I RO N M EN T A L
Ambient Temperature -4 to +122 °F (-20 to +50 °C)
Minimum airflow 4ft3/min (0,1m3/min)
Humidity (non-condensing) 0 to 95%
Transient Immunity per ANSI / 587 C62.41
M E C H AN I C AL
Dimensions, including connectors
19in wide, 1.73in high, 12in deep
43cm wide, 4,5cm high, 30cm deep
Product Weight 23.5lb (10,66kg)
Packaged Weight 32lb (14,5kg)
Notes: Actual distance will depend on the camera’s inrush and operating current, minimum operating voltage, and the wire’s environmental temperature. Please consult NVT
Customer Support for further information.
Wire should be category rated Unshielded Twisted-Pair (UTP) cable, Low voltage camera
power, video, and RS-422 or RS-485 telemetry may be sent within the same wire bundle.
Do not run 24VAC or 28VAC in the same wire bundle with analog telecom signals. However
you may share the same wire/cable tray.
An online wire Power Distance Calcula tor is available at www.nvt.com under Product
Support.
A C C E SS O R IE S (included)
Mounting Rack mount “L” brackets for front,
rear, or wall installations;
rubber feet for desk applications
Cables Sixteen 2ft (60cm) coax jumpers
Molded IEC power inlet cord 7ft (200cm)
O P T I ON A L E Q U IP M E NT
Mounting NV-RMBK2 Rear Mount Support Kit
(designed for use with thinner
metal equipment racks)
NV-WMBK2 Wall Mount Bracket Kit (heavy duty)
R E G U LA T OR Y
Specifications subject to change without notice.
Loading...