NVT NV-16PS13-PVD Specsheet

Model NV-16PS13-PVD

Power Supply Passive Video Receiver Hub

Front

Rear

Features:

• Provides Class 2 SELV camera power while receiving video transmission
and delivering P/T/Z telemetry all over a single 4-pair Cat5e cable

• Standard telecom/datacom structured cabling pinouts per EIA/TIA 568B

• Independently selectable 24VAC-OFF-28VAC with 1 Amp per channel*

• Automatic-reset fault protection; transient protection

• Individually floating outputs ensure total ground-loop immunity

• Diagnostic LEDs show load/no load, miswires, and overload conditions

• Use with the NV-216A-PV, NV-218A-PVD, or NV-226J-PV transceiver at the camera

• Power cameras via UTP over significant distances (See Power Distance Chart)

• 1U high; 12" deep; wall, desk, or rack-mountable, 2ft (60cm) BNC Cables included

• Limited lifetime warranty

The 16-channel NV-16PS13-PVD is a key hybrid component that consolidates all CCTV
system cabling using standard EIA/TIA 568B structured building wiring. Designed for installation in the
IDF/Telecom Closet or MDF/Equipment Room, the Power Supply Passive Video Receiver Hub has
independently selectable 24VAC-OFF-28VAC outputs that can support at-distance camera loads up to
1 Amp per channel (10 Amps aggregate). Use with NVT’s PVDTMtransceivers for cable runs under 750ft
(225m). A built-in passive receiver hub allows connection to DVR or an encoder for IP transmission. Per­channel diagnostic LEDs display load/no-load, miswires, or fault conditions at a glance. Automatic-reset
fault protection, transient protection, and ground loop free individually floating outputs.

*10 Amps, aggregate to comply with CB1IEC60065

Network Video Technologies

4005 Bohannon Drive • Menlo Park, CA 94025 • USA

(+1) 650.462.8100 • 800.959.9870 • FAX [phone]

nvt.com • [e-mail]

-41-

Model NV-16PS13-PVD

Power Supply Passive Video Receiver Hub

Technical Specifications

W I R E D I ST A NC E (Power Distance Charts)

Supply voltage, wire resistance and minimum camera operating
voltage determine the maximum camera distance. Examples
assume a minimum 21VAC at the camera:

Notes: Wire should be Cat5 or better/ low voltage camera power, video and RS-422
or RS-485 data may reside within the same wire bundle, however do not run 24 or
28VAC within the same wire bundle as other telecom or datacom signals.

C A M E R A P O W ER

Each camera is powered by a fully isolated (floating) Class 2
SELV output, individually switchable 24VAC / Off / 28 VAC
at up to 1 Amp (10 Amps aggregate). Each output is individually
thermistor protected for auto-reset after fault removal.

P O W E R

Power inlet IEC with molded power cord (included)
Voltage 115 / 230V
Current 3.0 / 1.5 Amps
Protection 5x20mm type T fuse 5Amp 250V
Wattage 325 Watts
Heat (power supply only) 125 BTU / Hour

(power supply with cameras) 1,200 BTU / Hour

F R O N T PA NE L L E D s

System Power: Blue LED
Per-channel LED Indicates:

Off No load connected
Green Load connected and working
Amber Mis-wiring detected
Red Overload fault condition

E N V I R O N M E NT A L

Ambient Temperature -4 to +122 °F (-20 to +50 °C)
Minimum airflow 20ft3/min (0.5m3/ min)
Humidity (non-condensing) 0 to 95%
Transient Immunity per ANSI / 587 C62.41

V I D E O

Frequency response DC to 5 MHz
Attenuation 0.5 dB typ
Common-mode / Differential-mode rejection

15 KHz to 5 MHz 60 dB typ

Impedance

Coax, female BNC 75 ohms
UTP, RJ45 100 ohms

Network Wiring One four-pair Cat5 or better per channel

Network Video Technologies

4005 Bohannon Drive • Menlo Park, CA 94025 • USA

(+1) 650.462.8100 • 800.959.9870 • FAX [phone]

nvt.com • [e-mail]

M E C H A N I C A L

Dimensions, including connectors

19in wide, 1.73in high, 12in deep

43cm wide, 4,5cm high, 20cm deep

Weight 24.9lb (11,3kg)

A C C E S S O R I ES (included)

Mounting Rack mount “L” brackets for front,

rear, or wall installations;

rubber feet for desk applications

Cables Sixteen 2ft (60cm) coax jumpers

Molded IEC•power inlet cord 7ft (200cm)

O P T I O N A L E Q UI P M E N T

Mounting NV-RMBK2 Rear Mount Support Kit

(designed for use with thinner

metal equipment racks)

NV-WMBK2 Wall Mount Bracket Kit (heavy duty)

R E G U L A T OR Y

-42-