NVT NV-16PS10-PVD Specsheet

Model NV-16PS10-PVD

Power Supply Cable Integrator Hub

Front

Rear

Features:

• Provides Class 2 SELV camera power and pass-through video and telemetry data
connectivity for up to 16 cameras, each via a single RJ45 4-pair UTP cable

• Standard telecom/datacom structured cabling pinouts per EIA/TIA 568B

• Independently selectable 24 or 28VAC with 1 Amp max per channel*

• Automatic-reset fault protection; transient protection

• Individually floating outputs ensure total ground-loop immunity

• Diagnostic LEDs show load/no load, miswires, and overload conditions

• Use with the NV-216A-PV or NV-218A-PVD transceivers or the NV-226J-PV transmitter at the camera

• Power cameras via UTP over significant distances (see Power Distance Chart)

• 1 U high; 12” deep; wall, desk, or rack-mountable

• Limited lifetime warranty

The NVT model NV-16PS10-PVD combines a 1 Amp/channel*† power supply with pass through video
and telemetry data, for up to 16 cameras, all over UTP wire. Designed for installation in the wiring/IDF
telecom closet, or at the Control/MDF room, the NV-16PS10-PVD consolidates connectivity via stan­dard 4-pair RJ45 EIA/TIA 568B compliant premises wiring and pinouts.

At the camera, Power, Video and Data connections are made using a PVDTMtransceiver via an RJ45
connector and a single 4-pair cable. Control/MDF room connections are achieved with a single 4-pair
RJ45 cable for each group of four cameras. Consolidated P/T/Z telemetry data, if required, passes through
the NV-16PS10-PVD’s data path, and is connected to the controller via another 4-pair RJ45 cable.

*10 Amps, aggregate to comply with CB / IEC 60065

Network Video Technologies

4005 Bohannon Drive • Menlo Park, CA 94025 • USA

(+1) 650.462.8100 • 800.959.9870 • FAX [phone]

nvt.com • [e-mail]

-32-

Model NV-16PS10-PVD

Power Supply Cable Integrator Hub

Technical Specifications

W I R E D I S T A N C E (Power Distance Charts)

Supply voltage, wire resistance and minimum camera operating
voltage determine the maximum camera distance. Examples
assume a minimum 21VAC at the camera:

Notes: Wire should be Cat5 or better/ low voltage camera power, video and RS-422
or RS-485 data may reside within the same wire bundle, however do not run 24 or
28VAC within the same wire bundle as other telecom or datacom signals.

V I D E O

Frequency response DC to 5 MHz
Attenuation 0.5 dB typ
Common-mode / Differential-mode rejection

15 KHz to 5 MHz 60 dB typ

Impedance

Coax, female BNC 75 ohms
UTP, RJ45 100 ohms

Network Wiring One four-pair Cat5 or better per channel

C A M E R A P O W E R

Each camera is powered by a fully isolated (floating) Class 2 SELV
output, individually switchable 24VAC / Off / 28 VAC at up to 1 Amp
(10 Amps aggregate). Each output is individually thermistor protected
for auto=reset after fault removal.

P O W E R I N P U T

Power inlet: IEC•with molded power cord (included)
On-Off Switch Rear panel
Voltage 115 / 230 VAC
Current 3.0 / 1.5 Amps
Frequency 50 / 60 Hz
Protection 5A slo-blo 8 x 20mm fuse and thermal shutdown
Wattage 325 Watts
Heat (power supply only) 125 BTU / hour

(power supply with cameras) 1,200 BTU / hour

F R O N T- PA N E L L E D s

Blue LED System power on
Per-channel LED indicates: Off No load connected

Green Load connected and working
Amber Mis-wiring detected
Red Overload shutdown condition

E N V I R O N M E N T A L

Ambient Temperature -4 to +122 °F (-20 to +50 °C)
Minimum airflow 4 ft

Humidity (non-condensing) 0 to 95%
Transient Immunity per ANSI 587 C62.41

3

/min (0,1m3/min)

M E C H A N I C A L

Dimensions including connectors: 19in wide, 1.73in high, 12in deep

Weight 22lb (10kg)
Mounting Wall, desk, or rack mount, brackets

(483mm wide, 44mm high, 305mm deep

A C C E S S O R I E S (included)

Mounting Rack mount “L” brackets for front,

Cables Molded IEC power inlet cord 7ft (200cm)

rear, or wall installations;

rubber feet for desk applications

R E G U L A T O RY

Specifications subject to change without notice.

Network Video Technologies

4005 Bohannon Drive • Menlo Park, CA 94025 • USA

(+1) 650.462.8100 • 800.959.9870 • FAX [phone]

nvt.com • [e-mail]

-33-