T2FAM-EX Wiring Diagram
AM/FM
Modern Rock
Drift-Follow Th
Living For
MENU
3:09 pm
OK
Concerto EZ Port
Model NV-I8GEZP
Device 2 Device 3
Device 1
Device 4 Device 5 Device 6
Connect to
NV-I8GM
NuVo Technologies LLC He bron , Kentu cky USA
www.nuvotechnolog ies .com
USE NV-T2 DAA WITH
OPTION AL NV-T2 FXC
AND SIRI US ANTEN NA
IN
L
OUTPUT POWER
20W/6OHM X2
L
R
SOURC E INPUT S
TUNE R A
ANTE NNA
VARIABL E
OUTPUT
TIP=L
RING=R
FIXED
OUTPUT
ZONE 1
1 2 3 4 5
L
R
1 2 3 4 5
AUDI O
ZONE 2
R
VARIABL E
OUTPUT
TIP=L
RING=R
FIXED
OUTPUT
L
R
OUTPUT POWER
6
6
20W/6OHM X2
CONNEC T TO
NV-I8X
USE NV-SL C1
CABLE
SOURC E LINK
L
TUNE R B
ZONE 3
AUDI O
VARIABL E
OUTPUT
TIP=L
RING=R
FIXED
OUTPUT
R
OUTPUT POWER
20W/6OHM X2
1
4
SOURC E STATUS INP UTS
NuVoNe t
SYST EM
2 3
ZONE 5
VARIABL E
OUTPUT
TIP=L
RING=R
FIXED
OUTPUT
RS 232
www.nuv otech nolog ies.c om
VARIABL E
OUTPUT POWER
20W/6OHM X2
4
8
OUTPUT
OUTPUT POWER
TIP=L
20W/6OHM X2
RING=R
FIXED
OUTPUT
ZONE 6ZONE 6
1 2 3
4
EMITT ER OUTP UTS DIGITA L LINK
SUM1
SUM2
5
6
EXT. MUTE
SYSTE M
SYS ON
R
T
E
E
T
N
I
3033118
VARIABL E
OUTPUT
TIP=L
RING=R
OUTPUT
ZONE 7& 8
K
CM
FIXED
CONNEC T TO
NV-I8EZ P1
USE NV-NC 1
NETWO RK
CONFORMS TO UL
STD.6006 5 CERTIF IED
TO CAN/CSA STD .
C22.2 No.6 0065:0 6
CABLE
RoHS
RS-23 2
PROGR AM
CONNEC T TO
NV-I8X
USE NV-SL C1
CABLE
IR INPU T
VARIABL E
OUTPUT
OUTPUT POWER
20W/6OHM X2
TIP=L
RING=R
FIXED
OUTPUT
ZONE 4
2
3
1
5
6
5 6 7
ZONE TR IGGER O UTPUT S
Model N V-T2FAM -EX
Dual SIR IUS Rea dy AM/FM Tun er
NuVo Techn ologi es LLC Hebron, KY US A •
0728
USE CNLY WITH 250V FUSE
MODEL NV-I8DM
SIX SOURCE EIG HT ZONE
AUDIO DISTRI BUTIO N SYSTE M
120V 60Hz 50 0W
FUSE:T5 A
NuVo Technolog ies Cin cinna ti Ohio U SA
www.nuvot echno logie s.com
CONFORM S TO
R
UL STD.650 0
US
C
CERTIFIE D TO
CAN/CSA ST D.E60 065
3033118
Diagram shown using the Grand Concerto System
T2FAM-EX Quick Setup Guide for Use With NuVoNet
The T2FAM-EX Dual Tuner is the perfect broadcast music solution for whole-home audio. The internal NuVoNet capability of the
T2FAM-EX allows it to easily communicate in real time with the NuVo Grand Concerto and Essentia E6G Control Pads. The following
is a step-by-step guide for setting up and installing the T2FAM-EX for use with the Grand Concerto and Essentia NuVoNet Suites.
Step 1: Upon unpacking your T2FAM-EX Tuner, establish what audio inputs, 1-6, the T2’s A and B audio outputs will represent. Plug
the T2 into an AC power source.
Step 2: Attach the audio outputs A and B of the Tuner to the appropriate numbered inputs on the Grand Concerto or Essentia
System.
Step 3: Connect the CAT5 from the NuVoNet output on the rear panel of the Tuner to one of the Device inputs on the Grand Concerto
EZ Port or the Essentia Allport. This will enable communication to the System’s Control Pads. Note that a single CAT5 connection
provides information from both tuners A and B. A final CAT5 Connection should then be made to the NuVoNet CAT5 input on the
back panel of the Grand Concerto or Essenita main amplifier for the NuVoNet RJ45 on the Grand Concerto EZ Port or the Essentia
Allport. This completes the necessary connection for the NuVoNet communication.
2
Step 4: Complete the antenna connection on the back panel of the Tuner using standard RG6 coaxial cable. Quad shielded cable is
recommended. When the antenna is connected, the Tuner will begin receiving a signal for both Tuners A and B.
Step 5: When the Tuner is plugged into an AC power source the front panel display will move through a boot procedure. When this
procedure is complete a message, Uninitialized State Detected will appear.
Step 6: Following the prompt from the display, touch the OK button on the Tuner’s front panel control. This will display a regional
tuning selection, USA and Canada, Western Europe, Australia, and New Zealand. Make to appropriate selection to match the Tuner s
geographic location.
Step 7: Touching OK on the front panel controls will prompt a second screen on the display. This will read, Set Tuner A Mode,
Standalone, Source 1, Source 2, Source 3, Source 4, Source 5, and Source 6. The top selection, Standalone, will be highlighted. This
choice is used for any purpose that is not NuVoNet communication. Using the down arrow on the far right of the front panel
controls, scroll to the desired source input number, and touch OK to select. The display will automatically go to Tuner B setup.
Repeat the steps for setting Tuner A. If NuVoNet is not connected or all available sources have been assigned, then the source
selections will be grayed out.
Step 8: When the desired source number is selected, the display will return to the first screen. Both outputs A and B will display
the lowest AM band frequency by default. At this point full tuning capability can be done from the Tuner’s front panel, or an
addressed NuVo Control Pad.
Step 9: When both Tuner outputs are set, make sure the NuVoNet CAT5 connection between the Tuner s back panel and the
system EZ Port is complete.
The T2FAM-EX Tuner is now ready for NuVoNet communication with either the Grand Concerto or Essentia E6G distributed audio
systems.
Please see the complete installation guide for understanding the full use of your T2FAM-EX Tuner.
3
Loading...