Numark Industries TT1910 User Manual

Download

Professional Disc Jockey Products

TT1910 Direct-Drive Turntable

OWNER’S MANUAL

NUMARK INDUSTRIES

11 Helmsman Road, North Kingstown, RI 02852

http://www.numark.com

TT1910

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK

DO NOT REMOVE ANY COVER. NO USER- SERVICEABLE PARTS

INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL

The lightning flash with arrowhead symbol within the

equilateral triangle is intended to alert the user to the presence

of un-insulated “dangerous voltage” within the product’s

enclosure that may be of sufficient magnitude to constitute

a risk of electric shock to persons.

The exclamation point within the equilateral triangle is intended

to alert the user to the presence of important operating and

maintenance (servicing) instructions in the literature

FOR USA & CANADIAN MODELS ONLY

TO PREVENT ELECTRIC SHOCK DO NOT USE THIS (POLARIZED)

PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHER

OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

ONLY.

accompanying this appliance.

CAUTION

PREVENT BLADE EXPOSURE.

5. Water and Moisture - This product should be kept away from direct contact with liquids.

6. Heat - Avoid placing this product too close to any high heat sources such as radiators.

7. Power Sources - This product should be connected to a power supply only of the type described in these operating instructions, or as marked on the unit.

8. Power Cord Protection - Power supply cords should be routed so that they are not likely to be walked upon or pinched by items placed on or against them. When removing the cord from a power outlet be sure to remove it by holding the plug attachment and not by pulling on the cord.

9. Object and Liquid Entry - Take care that objects do not fall into and that liquids are not spilled into the inside of the mixer.

10. Damage Requiring Service - This product should be serviced only by qualified personnel. If you have any questions about service please contact Numark at the number(s) shown on the back cover of this manual.

SAFETY INSTRUCTIONS

1. Read Instructions - All the safety and operating instructions should be read before this product is connected and used.

2. Retain Instructions - The safety and operating instructions should be kept for future reference.

3. Heed Warnings - All warnings on this product and in these operating instructions should be followed.

4. Follow Instructions - All operating and other instructions should be followed.

11. Grounding or Polarization - Precautions should be taken so that the grounding or polarization means built into the mixer is not defeated.

NOTE: This apparatus does not exceed the Class A/Class B (whichever is applicable) limits for

radio noise emissions from digital apparatus as set out in the radio interference regulations of the Canadian Department of Communications.

WARNING: To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture. Electrical equipment should NEVER be kept or stored in damp environments.

Please record the serial number of your unit as shown on the back of the chassis as well as the name of the dealer from whom you purchased the unit. Retain this information for your records. Please return the warranty card enclosed to register your mixer with us.

MODEL: TT1910 PURCHASED FROM:_________________________ SERIAL NUMBER:__________________ DATE OF PURCHASE:________________________

Numark - The Proven Leader in DJ Technology

TT1910

CONGRATULATIONS!

You have just purchased the Numark TT1910 Professional Direct Drive Turntable. This unit has been design to provide years of reliable operation in an easy to use design. Thank you for purchasing a Numark Product and enjoy the

mix......

TABLE OF CONTENTS

Safety Information Page 2 Product Registration

Introduction Page 3 Diagram and Parts Description Page 4 Assembly Page 4 Operating Instructions Page 7 Specifications Page 7 Warranty and Service Page 8

Contents of this package

1. Main Unit 1

2. Turntable platter 1

3. Turntable mat 1

4. Dust cover 1

5. 45-rpm adaptor 1

6. Counterweight 1

7. Headshell 1 (cartridge attached on cetain models)

8. Operating instructions 1

9. Registration Card 1

Numark - The Proven Leader in DJ Technology

TT1910

http://www.numark.com

TT1910 DIAGRAM...

PARTS DESCRIPTION

(1) 45-rpm Adaptor (2) Anti-static slip mat (3) Center Spindle (4) Stroboscope (5) Start/Stop Button (6) Speed Select Button (7) Strobe Dots (8) Target light (9) Power Button (10) Headshell

(11) Pitch Control Slider (12) Tonearm (13) Arm Rest (14) Cueing Lever (15) Anti-skating Knob (16) Counterweight (17) 12V BNC Light Connector (18) Hinge For Dust Cover

Numark - The Proven Leader in DJ Technology

TT1910

CENTER SPINDLE

ASSEMBLY

1. Remove the main unit with the packing from the box and take off the packing material. DO NOT DISCARD ANY PACKING MATERIAL. The headshell, counterweight, and other parts are contained within the packing material.

2. Set the 45-rpm adaptor on the main unit.

3. Set the voltage selector switch to the 110-127 or 220-240V position according to the voltage of power supply. (This unit has been preset for 110-127V AC).

4. Insert the turntable platter onto the center spindle.

6. Set the turntable mat on the platter.

7. Installing the cartridge: When installing a cartridge, refer to the operating instructions of that cartridge.

During installation, attach the stylus protector to guard the stylus tip from damage. If you have purchased a unit with the cartridge included then that cartridge is already installed on the headshell (You may skip to line 8).

(1) Connect the lead wires to the cartridge terminals. The terminals of most cartridges are color coded. Connect each lead wire to the terminal of the same color.

White (L+) Left channel+ Blue (L-) Left channel Red (R+) Right channel+ Green (R-) Right channel

(2) Install the cartridge to the headshell and tighten it with screws provided with the cartridge.

8. Insert the headshell into the front end of the tonearm, then turn the locking nut clockwise with the head shell firmly held horizontally.

Numark - The Proven Leader in DJ Technology

TT1910

Release tab

9. Slide counterweight onto the rear of the tonearm. Twist it lightly and it will screw onto the rear shaft of the tonearm.

10. Adjustment of horizontal zero (O) balance with stylus pressure and anti-skating :

(1) Remove the stylus protector, do not touch the stylus tip during the adjustment. (2) Set the cueing lever to the lower position so it does not effect tone arm height. (3) Release the arm clamp and lift the tonearm from the arm rest so it moves freely. (4) Rotate the counterweight until the tonearm is approximately balanced horizontally (floats freely).

(5) Refasten the tonearm with the arm clamp.

Tonearm

Counterweight

(6) Hold the counterweight stationary with one hand and rotate only the stylus-pressure ring to bring the number "O" of the ring into alignment with the center line on the tonearm rear shaft.

(7) Rotate the counterweight with scale ring clockwise to the correct stylus pressure following the manufacture's recommendation.

(8) Set the anti-skating control knob to the same value as the stylus pressure unless your manufacturer specifies otherwise

11. Install the dust cover to the main unit. This lid is not designed for continual removal. If you need to remove the lid press both release tabs at the same time.

CONNECTIONS

1. Connect the power cord to the power outlet.

2. Connect the unit's output terminals from the rear of the unit to the PHONO jack of your DJ mixer or home amplifier/receiver.

Output terminals Phono input of mixer L (White) --------------> L Channel

R (Red) ----------------> R Channel GND (Spade) --------> GND

•Notes: Be sure to connect the ground terminal firmly to the amplifier or receiver. If this

connection is not made or is loose, a power source "HUM" may result.

Numark - The Proven Leader in DJ Technology

indicator and the strobe-illuminator will light up.

record with a large center hole, place the 45-rpm adaptor on the center spindle.

rotate.

descend slowly onto the record and play begins.

tonearm to the arm rest, secure the tonearm with the arm clamp .

push the power button to turn off the power.

tip during play. Push the target light button, the target light will be raised into position for illuminating the stylus tip.

When not in use, keep the target light lowered through depression.

observe the strobe dots, if the strobe dots appear to the right, the pitch is slower than the rated speed, if flow to the

left, the pitch is faster than the rated speed, if the strobe dots appear stationary, which means the platter is in normal

turntable speed. Move the pitch control slider up or down to adjust the speed.

PLACEMENT

•Do not place the unit in a location where it will be exposed to direct sun light or near a heating appliance.

•Do not place the unit in a location where there is high humidity or a lot of dust.

•Cartridge may pick up slight sound pressure or vibrations of the speakers coming along the floor or through the air resulting in howling. Find a location which is very

stable and free vibration.

•The legs have functions for adjusting the height of the unit itself. Adjust the legs to stabilize the main body

horizontally.

MAINTENANCE

•Clean the stylus periodically with a soft brush to prevent the accumulation of dust.

•When the sound becomes distorted or noisy, check the stylus. If worn out, replace it with a new one.

•From time to time, the dust cover and turntable cabinet should be wiped with a soft, dry cloth. Any volatile

materials as alcohol,thinner, benzine, etc.,may remove the paint or damage the luster, should not be used.

SPECIFICATIONS

Turntable section Type 2-speed, full manual Driving method Direct drive

Motor 8pole,2phase,

brushless DC motor

Turntable platter Aluminum diecast 330mm dia. Turntable speed 33-l/3 and 45 rpm Starting torque more than 600g-cm

Braking System Electronic Brake Wow and flutter Less than 0.20%

S/N ratio 55dB (DIN-B)

Tonearm section Type Universal s-shaped tubular arm

Effective length 220mm General

Power supply AC110-127V/220-

240V,50/60Hz

Power consumption 20 Watts Dimension(WxDxH) 450 x 350 x 148 mm

17 3/4” x 13 3/4” x 5 7/8”

Weight 7.5 Kgs 16 lbs

Specifications and design may be changed without notice

for improvement.

Numark - The Proven Leader in DJ Technology

TT1910

Professional Disc Jockey Products

Warranty and Service Information

Numark Industries, LLC and Numark International, Inc. (hereafter “Numark”) warrants each new product manufactured and/or supplied by it to be free from defects in material or workmanship under conditions of normal use and service for 360 days, beginning on the date of purchase from an authorized Numark Dealer, but not to exceed 2 years from date of shipment by Numark.

The Numark obligation under this warranty is limited to repairing or replacing, at its option, the product or part(s) therein; which upon examination by Numark shall appear to be defective or not up to factory specifications; providing the Numark product is returned (transportation prepaid) to Numark.

Numark shall not be liable for any damages, consequential or otherwise, resulting from the use and operation of this product and makes no other warranty(s) either express or implied on this product, including any warranty of merchantability.

This warranty does not extend to any of our products which have been subjected to misuse, neglect, accident, incorrect wiring not our own, improper installation, or use in violation of instructions furnished by us, nor extended to units which have been repaired or altered outside of our factory, nor to cases where the serial number thereof has been removed, defaced, or changed, nor to accessories used therewith not of our own manufacture. Numark reserves the right to make changes or improvements in its products, during subsequent production, without incurring the obligation to install such changes or improvements on previously manufactured equipment.

To place this warranty into effect, the enclosed WARRANTY REGISTRATION CARD must be returned to Numark Industries, LLC within thirty (30) days after date of purchase.

This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

Some states do not allow the exclusion or limitation of incidental or consequential damages so the above limitation or exclusion may not apply to you.

EQUIPMENT TRANSPORT

A Return Authorization number should be obtained from Numark through the addresses or phone numbers below.

It is the customer’s obligation, when returning faulty equipment, to properly pack the Numark equipment in its original packaging. Failure to do so may inadequately protect the equipment in transit and, therefore, jeopardize the customer’s warranty. The defective Numark equipment should be sent, FREIGHT PREPAID with Return Authorization number to:

NUMARK INDUSTRIES 11 Helmsman Road North Kingstown, RI 02852 U.S.A.

Attention: Service Department

Telephone: +1 (401) 295-9000 Fax: +1 (401) 295-5200

E-mail: numark@numark.com

Numark Industries TT1910 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual