Numark Industries CM-100 User Manual

Professional Disc Jockey Products

CM-100

PROFESSIONAL DJ MIXER

USER’S MANUAL

CM100

Safety Information

SAFETY INSTRUCTIONS

a) Read Instructions - All the safety and operating

instructions should be read before this product is connected and used.

b) Retain Instructions - The safety and operating instructions

should be kept for future reference.

c) Heed Warnings - All warnings on this product and in these

operating instructions should be followed.

d) Follow Instructions - All operating and other instructions

should be followed.

e) Water and Moisture - This

product should be kept away from direct contact with liquids.

f) Heat - Avoid placing this

product to close to any high heat sources such as radiators.

g) Ventilation - The appliance should be situated so that it’s

location or position does not interfere with it’s proper ventilation. For example, the appliance should not be situated on a bed, sofa, rug, or similar surface that may block the ventilation opening; or, placed in a builtinstallation, such as bookcase or cabinet that may impede the flow of air through the ventilation openings.

h) Power Sources - This product should be connected to a

power supply only of the type described in these operating instructions, or as marked on the unit.

i) Power Cord Protection - Power supply cords should be

routed so that they are not likely to be walked upon or pinched by items placed on or against them. When removing the cord from a power outlet be sure to remove it by holding the plug attachment and not by pulling on the cord.

j) Object and Liquid Entry - Take care that objects do not fall

into and that liquids are not spilled into the inside of the mixer.

k) Cleaning – The appliance should be cleaned only as

recommended by the manufacturer.

Non-use Periods – The power cord of the appliance should be unplugged from the outlet when left unused for long

periods of time.

m) Damage Requiring Service -

Only qualified personnel should service this product. If you have any questions about service please contact Numark at the number(s) shown on the back cover of this manual.

n) Grounding or Polarization - Precautions should be taken

so that the grounding or polarization means built into the CD player is not defeated.

o) Internal/External Voltage Selectors - Internal or external

voltage selector switches, if any, should only be reset and re-equipped with a proper plug for alternative voltage by a qualified service technician. Do not attempt to alter this yourself.

WARNING: To reduce the risk of fire or electrical shock, do not expose this appliance to rain or moisture. Electrical equipment should NEVER be kept or stored in damp environments.

- The Leader in DJ Technology

CM100

VERY IMPORTANT

Please read this entire manual before connecting this unit to your system

For optimum performance:

• The crossfader is a user replaceable item and subject to wear. Excessive force can wear out the fader quickly. This is not a

warranted item.

•

Never use spray cleaners on the slide controls . Residues cause excessive dirt build-up and this will void your warranty. In normal use slide controls can last for many years. If they malfunction (usually because of a dirty or dusty environment) consult a

professional technician.

• Always make sure that AC power is OFF while making any connections.

• Use appropriate cables throughout your system. Do not use excessively long cables (i.e. over 50ft/14m) Be sure plugs and jacks

are tightly mated. Loose connections can cause hum, noise or intermittents that could easily damage your speakers. Make the input and output connections with readily available low-capacitance stereo cables. Quality cable makes a big difference in audio fidelity and punch. See your Numark dealer or an electronics or audio specialist store if you are not sure which cables to get.

• Never attempt to make any adjustments or repairs other than those described in this manual. Take the unit to your dealer or to an

authorized Numark Service Center.

• ALWAYS remember: “TURN AMPS ON LAST AND OFF FIRST”. Begin with master faders or volume controls on minimum

and the amplifier gain/input control(s) down. Wait 8 to 10 seconds before turning up the volume. This prevents transients which may cause severe speaker damage.

• Use restraint when operating controls. Try to move them slowly. Rapid adjustments could damage speakers due to amplifier

clipping.

• Avoid amplifier “clipping” at all costs: this occurs when the red LEDs (usually on the front panel of most professional power

amplifiers) start flashing. “Clipping” is when the power amplifier is distorting and working beyond it’s limits. Amplifier distortion is THE major cause of speaker failure.

• To prevent fire or shock hazard, do not expose the unit to rain or moisture. Never place cans of beer, soda, glasses of water or

anything wet on top of the unit!

Product Registration

Please record the serial number of your unit as shown on the back of the chassis as well as the name of the dealer from whom you purchased the unit. Retain this information and your original purchase receipt for your records. Please return the enclosed warranty card to register your unit with us.

MODEL: __________________________ PURCHASED FROM:_________________________ SERIAL NUMBER:__________________ DATE OF PURCHASE:________________________

- The Leader in DJ Technology

CM100

PROFESSIONAL DJ MIXER

CONGRATULATIONS!

You have purchased the CM100 Stereo Mixer by . This mixer has been designed to provide

dependable control over your input and output sources. Whether you install this piece in a permanent environment or take it on the road, you are sure to utilize the features of the CM100. The CM100 features all new circuitry and the latest in manufacturing and design technology to give you greater quality and better reliability than ever before. The fader-start technology is designed to work with fader-start CD players as well as other popular brands. The CM100 brings to you the finest quality of DJ equipment available today.

Thank you for buying Numark DJ products!

FEATURES...

• 8 line, 3 phono, 2 mic inputs

• Fader-Start Crossfader with front panel controls

• Split/blend cue options

• Panning on master fader with stereo/mono switch

• 5-band ±6/±12dB EQ with rear panel defeat

• Master balanced XLR outputs with Stereo/Mono controls

• Cues on each channel with cue/send rear output for sampling and booth cue monitor

• Channel gain control with PFL meter

• Neutrik™ “Combo” connector (1/4” or XLR plug) for DJ Mic

• Auto-talkover mic input with bass, treble

• Tape Out for direct recording

• Front panel BNC light connector

• Zone output

- The Leader in DJ Technology

+ 8 hidden pages