Nuband i-Touch NU-G0018 User Manual

-1 -

FCC Statement

This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions:

(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference
that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.

- 2 -

QUICK START GUIDE

COMPATIBILITY

The Nuband i-Touch smart wristband only supports the following selected
mobile devices:
iOS version (iOS 8.0 upwards): iPhone 5 onwards, iPod touch 5th Gen onwards,
iPad mini 2 onwards, iPad Air onwards
Android Phones (Android 4.4 upwards): Samsung Galaxy S4 onwards, Samsung

Note 3 onwards or other smartphone

1. You should charge your Nuband for 1-2 hours prior to use. Remove module as
diagram shown below and plug into USB charge socket in either a computer or a
USB plug. The indicating light flash when it is being charged.

Time: (Portrait) (Landscape)
Steps :
Search Radar:
Off:
Date:
Find Your Phone:

Week:
Sleep Monitor:
Message Notification:
Portrait/Landscape Switching:
Sedentary Reminder:
Remote Camera Control:

Calories:
Bluetooth Connection:
Function Setting:
Alarm Clock:
Call ID display:

-3 -

2. Install Free App: Go to App store or Play store, download this App: “Nuband
Flash HR” and install it. To use the App, make sure your mobile device is
connected to the Internet via Wi-Fi or 3G/4G.

3. Account Set-up: Open the “Nuband Flash HR” App. Set your personal
information to start.

4. Nuband Operation Instruction:

You can use the band by “Wrist turning” or “Touch screen”.
It is convenient to check the time by “Wrist turning”.
You need to turn on “Palming gestures” on the Nuband Flash HR App under device
setting state.

Keep the band screen horizontally.

The time will display

on the screen automatically.

Turn wrist over.

- 4 -

Touch Screen

Function

Starting-up

Hold finger on the screen for 10 seconds.
0000 a code will apper. This is your Nuband i-Touch
code. Note and use when binding device.

Touch the screen or turn the wrist over.

Swipe left and right.

Tap the screen.

Press and hold.

Swipe left or right to , find then hold and press to swtich off.

Swipe left or right to , press and hold until the band vibrates once.

Light up

the screen

Shutdown

Level directory

Secondary
directory

Phone finder

Enter sport mode

Confirm

Operation

Press and hold , then your phone will give off the alarm.
(This function is only available when phone is set to ringing mode and
is connected with the band.)

-5 -

Swipe left or right to , then swipe to . Press and hold until the
band vibrates once.

Function

Confirm

sport mode

Enter

sleep mode

Landscape or
portrait orientation

:Running/walking, :Yoga, :Rope Jump, :Basketball, :Cycling.
Swipe to the above modes, press and hold until the smartband vibrates
once to select the sport. The sport icon will flash when the chosen sport
mode is activated.
(Different sports can be chosen from the App. Walking is the default
setting, up to 4 additional sports can be added and monitored.)

Operation

Swipe left or right to , then swipe to and hold until appears.
will appear on the time screen or activate the auto-sleep mode in
device setting state of the App “Sleep monitor”.

PS: Function may be changed and upgraded according to the band firmware’s update.

- 6 -

Home Display

Nuband i-Touch comes with an OLED display with touch functionality.
The home screen is the time screen. It will display: date, time, week, battery
level and connection status.
There are two display modes of the time screen: portrait and landscape.

Using Nuband i-Touch in Wet Condition

Nuband i-Touch is splash-proof.
Nuband i-Touch is NOT fully water resistant. Please DO NOT wear it in the
shower or bath. Please remove the band before participating in any aquatic
sports.

Date

Time

Week

Battery level

Connection status

Portrait Display

Date

Time

Week

Battery level

Connection status

Landscape Display

-7 -

5. Pairing

Keep your phone with Bluetooth and WiFi “on” for this step. Keep the screen lit
and your Nuband i-Touch will show a radar icon .

There would be a bluetooth icon instead of the radar icon
in the device after successful connection.

Login to the App 【Device】 to
search for the device.
Select “Device” page, click
“Blinding device”

Tap the band ID icon for pair. If pair
success, press “PAIR” on request.

- 8 -

When successfully connected, a
Bluetooth icon will appear instead
of the radar icon on the Home

display of the band.

Trouble shooting:

If the connection between the band and
the App is unsuccessful, follow the steps
below:

Switch to the time screen on Nuband,
check the connection status: Bluetooth
or radar .

If Bluetooth icon displays on the screen:
Go to Bluetooth in phone settings and
forget the device. Disconnect the band
from other Bluetooth devices and the
phone system, and start the syncing
process until successful.

If radar icon displays on the screen:
Turn off the Bluetooth on your mobile
device for 3-5 minutes. Then turn on
Bluetooth and enter the App to search
and bind the band. Please keep the
screen of the band on during the
searching process.

Please connect the band and the App via
the App “Nuband Flash HR” instead of the
phone Bluetooth. If the connection is only
displayed in the Bluetooth function in the
mobile device system, such connection is
not completed.

IOS Device:

【Bluetooth Pairing Request】 will

pop up, click “Pair”, and finish
pairing.