N-Tron 604MFX-ST, 608MFXE-ST-15, 604MFXE-ST-80, 608MFXE-ST-80, 608MFXE-ST-40 User Manual

...
600 Series Industrial
Ethernet
Switches
Installation
12/15/05
Hardware
Guide
1
Industrial Ethernet Switch Installation Guide
604MFX-ST 604MFXE-ST-15 604MFXE-ST-40 604MFXE-ST-80 608MFX-ST 608MFXE-ST-15 608MFXE-ST-40 608MFXE-ST-80
12/15/05
2
Copyright, © N-TRON Corp., 2002 820 S. University Blvd., Suite 4E Mobile, AL USA 36609
All rights reserved. Reproduction, adaptation, or translation without prior written permission from N-TRON Corp. is prohibited, except as allowed under copyright laws.
Ethernet is a registered trademark of Xerox Corporation. All other product names, company names, logos or other designations mentioned herein are trademarks of their respective owners.
The information contained in this document is subject to change without notice. N-TRON Corp. makes no warranty of any kind with regard to this material, including, but not limited to, the implied warranties of merchantability or fitness for a particular purpose. In no event shall N-TRON Corp. be liable for any incidental, special, indirect, or consequential damages whatsoever included but not limited to lost profits arising out of errors or omissions in this manual or the information contained herein.
Warning
Do not perform any services on the unit unless qualified to do so. Do not substitute unauthorized parts or make unauthorized modifications to the unit.
Do not operate the unit with the top cover removed, as this could create a shock or fire hazard.
Do not block the air vents on the sides or the top of the unit.
Do not operate the equipment in the presence of flammable gasses or fumes. Operating electrical equipment in such an environment constitutes a definite safety hazard.
12/15/05
3
Safety Warnings
ELECTRICAL SAFETY
WARNING: Disconnect the power cable before removing the
enclosure top.
WARNING: Do not operate the unit with the top cover removed.
WARNING: Do not work on equipment or cables during periods of
lightning activity.
WARNING: Do not perform any services on the unit unless qualified to do so.
WARNING: Do not block the air vents.
WARNING: Observe proper DC Voltage polarity when installing
power input cables. Reversing voltage polarity can cause permanent damage to the unit and void the warranty.
LASER SAFETY (604/608MFXE Version Only)
WARNING: CLASS 1 Laser Product.
WARNING: Do not stare into the Laser Beam.
12/15/05
4
600 Series Industrial Ethernet Switch
The N-TRON 600 Series are product derivatives of the OSM/ESM family jointly manufactured by Siemens and N-TRON. The N-TRON 600 Series switches supports high speed layer 2 switching between ports, and is housed in a ruggedized steel enclosure, and can withstand industrial temperatures, as well as high shock & vibration, and caries an MTBF in excess of 1M hours.
The 604MFX (608MFX) is a 4 (8) port ruggedized Ethernet switch that is capable of auto negotiating 10/100 Mb and half/full duplex communications on 2 (6) copper ports, and contains two 100BaseFX Fiber Optic ports.
The 604/608MFX are managed switches that supports SNMP management software, as well as configuration by a CLI (Command Line Interface – Serial Port), Telnet, and/or Web based browsers.
The 600 Series Switches can also serve as a redundancy managers, detect faults in ring topologies and allow high-speed ring network healing, thus providing media redundancy for mission critical control applications.
Key Features
Full Managed Solution
Supports Web Based Management
802.1P QOS (Quality of Service) Supported
Port Mirroring supported
Supports Media Redundant Fiber Ring Topology
Full IEEE 802.3 & 100BASE-FX Compliance
Extended Environmental Specifications
Support for Full/Half Duplex Operation
Auto Sensing Speed and Flow Control
Industry Standard 35mm DIN-Rail Enclosure
Fully Redundant Isolated DC Power Inputs
12/15/05
5
PACKAGE CONTENTS
Please make sure the Ethernet Switch package contains the following items:
1. 600 Series Ethernet Switch
2. This Installation Guide
Contact your carrier if any items are damaged.
INSTALLATION
Read the following warning before beginning the installation:
WARNING
The FXE units contain a class 1 laser. Do not stare into the laser beam (fiber optic connector) when installing or operating the product.
Never install or work on electrical equipment or cabling during periods of lightning activity. NO USER SERVICABLE PARTS INSIDE.
Disconnect the power cable before removing the enclosure top. Do not operate the unit with the top cover removed
UNPACKING
Remove all the equipment from the packaging, and store the packaging in a safe place.
File any damage claims with the carrier.
12/15/05
6
600 Series Hazardous Location Installation Requirements
1. WARNING! Do not disconnect while circuit is live, unless area is
known to be non-hazardous.
2. WARNING! Install only in accordance with Local & National
Codes of .Authorities Having Jurisdiction.
3. Class I, Div 2 installation requires that all devices connected to this
product must be approved for the area in which it is installed.
4. Only hazardous location approved wiring with temperature ratings
greater than 80 C permitted for Class I, Div 2 installations operating at temperatures up to 60 C ambient.
Personnel Qualification Requirements
Only qualified personnel should be allowed to install and work on this equipment. Qualified personnel are defined as individuals who are familiar with the installation, assembly, startup, and operation of this product and who possess the relevant qualifications for their work e.g.:
Training in or authorization for connecting up, grounding, or
labeling circuits and devices or systems in accordance with current standards in safety technology.
Training in or authorization for the maintenance and use of suitable
safety equipment in accordance with current standards in safety technology.
First aid qualification.
DIN-Rail Mounting
Install the unit on a standard 35mm Din-Rail. When installing the unit in an enclosed cabinet, recess it to allow at least 3” of clearance for fiber optic cable bend radius, and 2 inches for TX cables and power connections. Please note the 600 Series units must be installed in the vertical orientation for cooling purposes. In this orientation, the power connector is at the top of the unit, and the signal cables exit from the bottom of the unit.
19” Rack Mounting
19” Rack mount kits are available. Please consult with your local sales representative for price & availability. Order part number: 900-RM
12/15/05
7
Loading...
+ 15 hidden pages